DOWNLOAD Sharp XV-Z90E (serv.man31) Service Manual ↓ Size: 5.84 MB | Pages: 62 in PDF or view online for FREE

This projector is equipped with a reverse/invert image
function which allows you to reverse or invert the pro-
jected image for various applications.

1 Press MENU. The “Picture” menu screen appears.

2 Press 

/

 to display the “PRJ Mode” menu

screen.

3 Press  /  to select the desired projection mode.

4 Press ENTER to save the setting.

5 To exit the menu screen, press MENU.

• This function is used for the reversed image and ceiling-

mount setups. See page 23 for these setups.

2,3

1, 5

4

English is the preset language for the On-screen
Display; however, this can be changed to German,
Spanish, Dutch, French, Italian, Swedish, Portuguese,
Chinese, Korean or Japanese.

1 Press MENU. The “Picture” menu screen appears.

2 Press 

/

 to display the “Language” menu

screen.

3 Press  /  to select the desired language.

4 Press ENTER to save the setting. The On-screen

Display is now programmed to display in the
language selected.

5 To exit the menu screen, press MENU.

2,3

1, 5

4

ⳭFront

ⳭRear

Normal image

Inverted image

Reversed image

Reversed and inverted image

2,3

1,4

1

1

1 The “Advanced” menu appears when the buttons

are pressed in the order shown below.

 - 

 - 

 - 

 - 

 - 

 - 

2 Press  /  to select a specific adjustment item.

3 Press  /  to move the   mark of the selected

adjustment item to the desired setting.

4 To exit the menu screen, press MENU.

• To reset all adjustment items, “Reset” in the "Picture" menu

screen and press ENTER.

• Advanced adjustment values are stored in all modes.

For less contrast of red
colour

For less contrast of
green colour

For less contrast of blue
colour

For less brightness of
red colour

For less brightness of
green colour

For less brightness of
blue colour

 

 

For more contrast of red
colour

For more contrast of green
colour

For more contrast of blue
colour

For more brightness of red
colour

For more brightness of
green colour

For more brightness of
blue colour

All image adjustment items are returned to the factory
preset settings.

Detailed picture adjustments can be made in addition
to the adjustments on the normal menu screen.

1

2

• Blocked air intake.

• Clogged ventilative hole.

• Cooling fan breakdown.
• Internal circuit failure.

• Burnt-out lamp.
• Lamp circuit failure.

• Lamp has been used for

over 2,400 hours.

TEMPERATURE
WARNING indicator

LAMP REPLACE-
MENT indicator

The internal
temperature is
abnormally high.

The lamp does not
light up.

The lamp requires
replacement.

• Relocate the projector to an area with proper

ventilation.

• Clean the ventilative holes.

(See page 49.)

• Take the projector to your nearest Sharp

Authorised Projector Dealer or Service
Centre for repair.

• Carefully replace the lamp. (See page 46.)
• Take the projector to your nearest Sharp

Authorised Projector Dealer or Service
Centre for repair.

• The warning lights on the projector indicate problems

inside the projector.

• There are two types of warning lights: a TEMPERATURE

WARNING indicator that warns you when the projector
is too hot, and a LAMP REPLACEMENT indicator that
warns you when to change the lamp.

• If a problem occurs, either the TEMPERATURE

WARNING indicator or the LAMP REPLACEMENT
indicator will illuminate in red. After turning off the
power, follow the procedures given below.

• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has

cooled down completely before turning the power back on. (At least 5 minutes.)

• If the power is turned off and then turned on again, for example during a brief rest, the LAMP REPLACEMENT indicator may

be triggered, preventing the power from going on. Should this occur, unplug the power cord from the wall outlet and plug it
back in again.

TEMPERATURE
WARNING
indicator

POWER
indicator

LAMP
REPLACEMENT
indicator

TEMP.

LAMP

POWER

The lamp in this projector operates for approximately 2,500 cumulative hours, depending on the usage environ-
ment. (As the usage environment can vary significantly, the projector lamp may not operate for 2,500 hours.) It is
recommended that the lamp be replaced after approximately 2,400 cumulative hours of use or when you notice a
significant deterioration of the picture and colour quality. The lamp usage time can be checked with the On-screen
Display.

• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.

This function allows you to check the accumulated lamp
usage time.

1 Press MENU. The “Picture” menu screen appears.

2 Press  /  to display the “Options” menu screen.

The lamp usage time will be displayed in “Lamp
Timer”.

3 To exit the menu screen, press MENU.

• It is recommended that the lamp be replaced after

approximately 2,400 cumulative hours of use. See page 46
for lamp replacement.

• Lamp has been used for over 2,400

hours.

• Lamp has been used for over 2,500

hours.

• Purchase a replacement lamp unit

(lamp/cage module) of the current
type BQC-XVZ90+++1 from your
nearest Sharp Authorised Projector
Dealer or Service Centre.

• Replace the lamp. (See page 46.) If

you wish, you may have the lamp
replaced at your nearest Sharp
Authorised Projector Dealer or
Service Centre.

The LAMP REPLACEMENT
indicator illuminates in red, and
“LAMP” and “ ” will blink in yellow
in the lower-left corner of the image.

A significant deterioration of the
picture and colour quality occurs.

The power will automatically turn off
and the projector will enter standby
mode.

“LAMP” and “ ” will blink in red in
the lower-left corner of the image,
and the power will turn off.

1,3

2