Sharp XV-Z201E (serv.man29) Service Manual ▷ View online
29
XV-Z200U/E, XV-Z201E
DT-300
DT-300
Note:
Do not put checkmark the "Continuous Flash Mode" and "Notify On Completion" boxes, but put checkmark the
"Reset Target After Download" box, all in Options.
Put checkmark the "Flash" box in Modes.
Do not put checkmark the "Continuous Flash Mode" and "Notify On Completion" boxes, but put checkmark the
"Reset Target After Download" box, all in Options.
Put checkmark the "Flash" box in Modes.
8. Click on "Flash".
The above screen shows up to get ready to write the program.
30
XV-Z200U/E, XV-Z201E
DT-300
DT-300
9. Now connect the AC power cord, and the program will be written. Wait for 4 minutes or so until the writing is
completed.
Do not disconnect the AC cord by at this time . Below windows is underwriting.
Do not disconnect the AC cord by at this time . Below windows is underwriting.
With the writing complete, the following screen shows up.
Click on "Close", and the upgrading ends.
The set may or may not get started itself. But disconnect and reconnect the AC power cord, and get the set started.
After up grade, OSD is in Japanese, Background is set None and Eco mode is ON.
So, change OSD is Englis, Background is set to SHARP and Eco mode is off, (Or, set to "SS5". However, lamp time
is also in this case.)
The set may or may not get started itself. But disconnect and reconnect the AC power cord, and get the set started.
After up grade, OSD is in Japanese, Background is set None and Eco mode is ON.
So, change OSD is Englis, Background is set to SHARP and Eco mode is off, (Or, set to "SS5". However, lamp time
is also in this case.)
31
XV-Z200U/E, XV-Z201E
DT-300
DT-300
TROUBLESHOOTING TABLE
Yes
No
Checking of Basic Operation
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
Yes
No
Does the digital RGB input
operate normally?
operate normally?
Does the video input operate
normally?
normally?
Is the component input acting
normally?
normally?
Is the analog RGB input acting
normally?
normally?
Is the user menu displayed?
Does the cooling fan rotate and
does the lamp light up?
does the lamp light up?
Go to "Checking of Power Unit".
Go to the "Check of IC2002 and
around I/O".
around I/O".
Go to "Checking of Lamp Lighting-up"
Check the formatter circuit and
its periphery.
its periphery.
Check of IC6004 (AD) or
IC3104 and check of analog
RGB input
IC3104 and check of analog
RGB input
Is there input signal at pins
(16), (18) and (20) of IC3104?
(16), (18) and (20) of IC3104?
Check of IC502 of the DVI-
TAN1 PWB and peripheral
circuits.
TAN1 PWB and peripheral
circuits.
Go to "Checking of Video
Input". Is the input signal of
IC3105 coming?
Input". Is the input signal of
IC3105 coming?
Check IC3102 and its
peripheral circuit.
peripheral circuit.
No
Check IC3104 and its
peripheral circuit.
peripheral circuit.
No
Check IC3105 and its
peripheral circuit.
peripheral circuit.
Does the POWER LED light up or
flicker in red or green?
flicker in red or green?
End
Does the set operate by the set's
key or the remote controller's
power key?
key or the remote controller's
power key?
32
XV-Z200U/E, XV-Z201E
DT-300
DT-300
Yes
No
Checking of Power Unit
Are connectors in the power unit
completely inserted?
completely inserted?
Yes
No
Is the lamp door closed
completely?
completely?
Close the lamp door completely by
screws.
screws.
Yes
No
Is the bimetal switch not cut?
Replace the bimetal switch or
press the red button to recover.
press the red button to recover.
Yes
No
Is AC voltage applied to AC input
both ends of D7001?
both ends of D7001?
Replace F7001.
Replace if any other damages, etc.
Replace if any other damages, etc.
Yes
No
Is DC voltage about 6V on C7105
both ends?
both ends?
Check around IC7003 of the
primary side and D7103.
Replace if any damages, etc.
primary side and D7103.
Replace if any damages, etc.
Yes
No
Is voltage about 360 V DC on the
cathode of D7004?
cathode of D7004?
Replace the ballast power
source side.
source side.
Yes
No
Is there rated voltage at the output
terminals of CN7101 and CN7102?
terminals of CN7101 and CN7102?
Check the secondly side circuit of
T7001, etc. Replace if any
damages, etc.
T7001, etc. Replace if any
damages, etc.
No
Check the primary side circuit of
IC7001, etc. Replace if any
damages, etc.
IC7001, etc. Replace if any
damages, etc.
Check the PWB circuits of relevant
output sides.
output sides.
Securely insert each connector.
Click on the first or last page to see other XV-Z201E (serv.man29) service manuals if exist.