DOWNLOAD Sharp XV-Z201E (serv.man29) Service Manual ↓ Size: 10.33 MB | Pages: 116 in PDF or view online for FREE

1. Feed the NTSC VIDEO

75% gray scale signal.

2. Group: VIDEO
3. Subject: CB-Offset

  CR-Offset

4. Make sure to perform this

setting after the DVD
white balance adjustment.

1. Adjust the white balance to x=286 and y=314.
2. Write the respective settings of the CB-Offset and CR-

Offset into the CB-Offset and CR-Offset of DTV and
DVD.

1. Feed the XGA 75% color

signal for each of R, G, B,
W, Mg, Cy and Ye.

2. Make sure to perform this

setting after the DVD
white balance adjustment.

1. Feed the XGA 75% gray scale signal, and record the

values of x, y and Y.

2. Feed the XGA 75% green signal, and record the values

of x, y and Y.

3. Feed the XGA 75% red signal, and record the values

of x, y and Y.

4. Feed the XGA 75% blue signal, and record the values

of x, y and Y.

5. Feed the XGA 75% cyan signal, and record the values

of x, y and Y.

6. Feed the XGA 75% magenta signal, and record the

values of x, y and Y.

7. Feed the XGA 75% yellow signal, and record the

values of x, y and Y.

8. Through RS232C, send each measurement data to

PIXEL.

1. Feed the XGA 75% gray

scale signal.

2. Group: PIXEL

Subject: R-GAIN (R)
B-GAIN (B)
Input 2 RGB input
XGA or SVGA

1. Adjust the white balance by controlling R-GAIN and

B-GAIN.
(Adjust x=286 and y=314.)

1. Perform this setting after replacement of the DLP chip

or when the combination of the DLP chip and the
formatter PWB has been changed.

2. Rating B C D E

1. Read the voltage rating

shown on the DLP.

2. Make the switch setting

corresponding to the rating.
(Inside the formatter PWB)

1. Make sure that the video output is normal.

1. Receive the digital signal.

1. Select OFF in the process mode.

Make sure that the off-timer starts with 5-minute
display, counts 1 minute in 1 second, and turns the
set off upon 0-minute display.

1. Heat the thermistor using a

dryer.

1. Make sure the "TEMP" is displayed.

1. Make the following settings

Destination

Process adjustment Remote controller setting

Europe

SS3

Factory setting 3

North America

SS4

Factory setting 4

»

»

There are following two methods.

»

Press the S2002 on the MAIN PWB.

»

Press the following keys in this order.

Adj up

→

Adj up

→

Adj down

→

Adj down

→

Adj right

→

Adj left

→

Enter

      Group

Subject

1st layer

DTV

Pedestal

DVD

VERSION

VIDEO

SS

AD

TEMP

OUTPUT1

PATTERN

OUTPUT2

LAMP

OUTPUT3

LINE

VIDEO1

      Group

Subject

2nd layer

DTV

Contrast

Tint

Color

Sharpness

CTI-Level

LTI-Level

CB-Offset
CR-Offset

Bright

B-DRIVE
R-DRIVE

DVD

Contrast

Tint

Color

Sharpness

CTI-Level

LTI-Level

CB-Offset
CR-Offset

Bright

B-DRIVE
R-DRIVE

VIDEO

Contrast

N-Tint
P-Tint
S-Tint

N-Color
P-Color
S-Color

Sharpness

CTI-Level

LTI-Level

CB-Offset
CR-Offset

Bright

B-DRIVE
R-DRIVE

AD

R-Bright

R-Contrast

G-Bright

G-Contrast

B-Bright

B-Contrast

DLP

Index Delay

R-Bright

R-Contrast

G-Bright

G-Contrast

B-Bright

B-Contrast

VIDEO1

N-Contrast
P-Contrast
S-Contrast

Color

NT3.58 Delay
NT4.43 Delay

PAL Delay

SECAM Delay

PIXEL

R-GAIN
B-GAIN
G-GAIN

Pedestal

R-Bright

R-Contrast

G-Bright

G-Contrast

B-Bright

B-Contrast

VERSION

Build

Boot Code

Config

Rom Code

GUI

ARM
ARM

SS

SS2

SS3 EU
SS4 US

SS5 JPN

SS6 CHIN

TEMP

Temp1
Temp2
Temp3
Temp4

OPTION

PW365 Gamma

DLP Gamma

PATTERN

Color Bar

Gray Scale

LAMP

Current Time

Histry1

History2
History3
History4

TOTAL TIME

LINE

OFF

LED

1) Prepare the RS232C cross cable and conversion cable at hand.

1. Connections

Connect the RS232C cross cable to a computer (Windows98 and higher OS), and the conversion cable to the
set.

2. Do not connect the AC power cord yet at this time.

2) Upgrading procedure

1. For upgrading the XV-Z200U/DT-300/XV-Z200E/XV-Z210E, use the "Flash Upgrader" program.
2. Decompress the attached file, and a folder is created.
3. Double-click on "FlashUpgrader.exe", and the following window appears

4. Click on the "Choose" button, and the following window appears.

5. Click on the arrow mark shown above, and select the decompressed folder.

6. Select "pwSDK.inf" in the folder.

7. Double-click on "pwSDK.inf".