DOWNLOAD Sharp XV-Z1E Service Manual ↓ Size: 740.03 KB | Pages: 42 in PDF or view online for FREE

)

(

)

(

»

1. Before replacing all the 3 LCD panels, project an image on the screen and bring it into focus.
2. Replace the panels with new ones.  But until the focus has been completely readjusted, be careful not to

change the distance between the set and the screen, nor to move the projection lens focus and zoom
rings.
If the focus is readjusted with a different positional relation, the relation between the projection distance
and the screen size is affected. In other words, a short-distance image (40 WIDE, for example) may get
out of the focus range, or a long-distance image (300 WIDE, for example) may come out of focus.

1. In adjusting the focus after replacement of one or two LCD panels, project an image on the screen and turn

the projection lens focus ring to get the non-replaced LCD panel into focus.

2. But until the focus has been completely adjusted for the new LCD panels, be careful not to change the

distance between the set and the screen, nor to move the projection lens focus and zoom rings.
(If the distance has been changed or the projection lens readjusted, repeat the above steps 1 and 2.)

1. Right-and-left focus adjustment (

θ

Y direction) .

Loosen the lock screws "b" and "c" and insert the eccentric screwdriver into the notch and hole "b".  Turn
the screwdriver until the right and left halves on the screen get into focus.
First get the right and left halves in balance.  Then improve the accuracy while making the adjustment 2
below.

2. Top-center-bottom focus adjustment (

θ

X and Z directions).

Loosen the lock screws "a" and "c" and insert the eccentric screwdriver into the notch and hole "a" or "c".
Turn the screwdriver until the top, center and bottom on the screen get into focus.  In adjusting this top-to-
bottom focus, temporarily tighten the lock screw "b" to fix the 

θ

Y direction adjustment.

3. Repeat the above steps 1 and 2 to finely adjust the focus.  Finally tighten up all the lock screws.

1

Carefully proceed with the focus adjustment because the adjusting directions are correlated.

2

In adjusting the convergence and focus, do not move the projection lens zoom and focus rings until the end
of all the adjustments.

»

The G-LCD panel has no convergence adjustment mechanism. Use this panel as convergence adjustment
reference.

»

Take the same procedure as for the G-LCD panel focus adjustment. Note that the adjustment range is small
in the Z direction. If the convergence is quite different between the B-LCD and G-LCD panels, roughly adjust
the convergence first and then the focus.

»

Use a crosshatch pattern signal for this adjustment.
Make the adjustment just for the G-colour and the relevant colour.
(1) Loosen the convergence lock screw "d".
(2) With the G-LCD panel’s screen center as reference, adjust the B-LCD panel in the X, Y and 

θ

Z directions.

(3) Finally tighten up the convergence lock screw "d".

X

Z

θ

Y

X

Y

θ

Z

X

Y

θ

Z

X

Z

θ

Y

Notch and hole "a"
(Use an eccentric
screwdriver.)

Notch and hole "b"
(Use an eccentric
screwdriver.)

Lock screw "b"
(

θ

Y direction)

G-LCD panel
mounting screws

 G adjusting plate

Notches and
holes "c"
(Use on eccentric
    screwdriver.)

Notches and holes "c"

Lock screws "c"

(Use an bladed screwdriver.)

Eccentric cam
(Y direction adjustment)

Eccentric cam
(X direction adjustment)

Eccentric cam
(

θ

Z direction adjustment)

Lock screw "d"
(convergence adjustment)

R•B adjusting plate

R•B-LCD

R•B-LCD panel
mounting screws

Lock screw "a"

FRONT

R-LCD

G-LCD

B-LCD

G-LCD

1

The eccentric cam is used for convergence adjustment. This means that the cam’s turning and the linear
movement are not always uniform.

2

This model is not equipped with the LCD image adjustment mechanism. This is because the dichroic prism
is used for image formation. When the LCD panels all get into the best focus, the images are almost
completely converged.

X direction

LCD right and left

Convergence Y direction

LCD top and bottom

θ

Z direction

Rotation around Z axis

LCD turning axis

Z direction

LCD optical axis

θ

X direction

Rotation around X axis

LCD top-to-bottom flapping

θ

Y direction

Rotation around Y axis

LCD right-to-left flapping

Specific

9DASPN-XGNV1U

Eccentric screwdriver Specific

9EQDRiVER-NV1A

General (redesigned)

9EQLNC-XGNV1U

General

9EQDRiVER-NV1B

General

           —

For M2.6 pan-head machine screw

0.5

85min

ø5

(ø3.5)

3.5

2

5

(16)

(R2)

(50)

CUT

100

80

Notch and hole "a"

Z and 

θ

X directions

Notch and hole "b"

θ

Y direction

Notch and hole "c"

Z, 

θ

X and 

θ

Y directions

X direction

±0.8mm Eccentric cam

Eccentric cam adjusting wrench

d

Hex wrench

Convergence

Y direction

±0.8mm Eccentric cam

Eccentric cam adjusting wrench

d

Hex wrench

θ

Z direction

±1°

Eccentric cam

Eccentric cam adjusting wrench

d

Hex wrench

Z direction

±0.8mm Notch and hole "a" & "c"

Eccentric screwdriver,

a, c

Phillips

Focus

θ

X direction

±1°

Notch and hole "a" & "c"

 Bladed screwdriver

a, c

 screwdriver

θ

Y direction

±1°

Notch and hole "b" & "c"

b, c

Z direction

±0.2mm

Focus

θ

X direction

±1°

Same as for R and B colours

θ

Y direction

±1°

With the top cabinet removed
(1) Remove the output shield.
(2) Disconnect the LCD flat cable from the output PWB connector.
(3) Remove the lock screws "b" and "c". Detach the R/B adjusting plate or the G adjusting plate together with the LCD

panel.

(4) Separate the LCD panel from the adjusting plate.
(5) Mount a new LCD panel in the reverse order of the above steps (1), (2), (3) and (4).

~

Readjust the convergence and focus. Note that the G LCD panel needs no convergence adjustment and has

a small adjustment range in the Z direction.

X

Z

θ

Y

X

Z

θ

Y

X

Y

θ

Z

X

Y

θ

Z

G-LCD panel
mounting screws

 G adjusting plate

Lock screws "c"

Lock screws "c"

Lock 
screws "c"

Lock 
screws "b"

R•B adjusting plate

R•B-LCD

R•B-LCD panel
mounting screws

FRONT

R-LCD

B-LCD

~

G-LCD

G-LCD

1

1

4

4

2

2

2

3

3

3

3