DOWNLOAD Sharp XG-PH50X (serv.man15) Service Manual ↓ Size: 15.84 MB | Pages: 127 in PDF or view online for FREE

- Turn on the power (lamp on state) and wait for 15 minutes for aging.
- Enter the adjustment process mode with S3602 (tact switch) on the main board.

In case that top cabinet covered S3602, you can enter by pushing key continuously in sequence.

key pad

On -> Up -> Down -> Up -> Down -> Enter -> Enter -> Menu

Remote controler On -> Vol up -> Vol down -> Vol up -> Vol down -> Enter -> Enter -> Menu

* You can exit from factory mode by same method.(Or select "EXIT" in the process mode to exit.)

- Select the group to adjust with the DOWN key or the UP key,  and enter the adjustment item with the ENTER

key on the remote control or key pad.

- Select the adjustment item with the DOWN  key or the UP key.
- Use the LEFT  key or the RIGHT  key for adjustment.
- To return from the adjustment item to the adjustment group, use the UNDO key or the MENU key.
- Change internal test pattern and input signal with the MUTE key

1. Turn on the power (the

lamp lights up) and warm
up the system for 15 min-
utes.

2. Select the following group

and subject.
Group: SSS
Subject: S2

1. Press S3602 to enter the process mode.
2. Execute the S2 command on the SSS menu.

*With the S2 command, all the circuit boards than
the PC board will be initialized.

(Note)

Since the PC I/F unit is initialized with S1, do not
carry out S1.
The PC I/F unit is already adjusted.
When the PC I/F unit must be adjusted, in such
case as S1 is carried out by mistake, adjust it
according to the "PC I/F adjustment method" at
the end of this document.

3. Wait approximately 30 seconds and when "IN-

PUT1" appears, turn off the power.

4. After all the fans stop, turn the power back on.

1. Signal input: 64 STEP color

bar signal.

2. Select the following group

and subjects.
Group : DLP
Subject : CW-INDEX

1. Feed the signal to INPUT 1.
2. Select subject and make adjustment so that the uni-

formity should be smooth.

1. Read a sticker which is written mac address on main

board.

2. Write MAC address by 232c serial cable.(For the pro-

cedure, refer to the attachment.)

1. SRead voltage rank of DLP

description.

2. Select the following group

and subjects.
Group : DLP
Subject : DMD-BIN

1. Adjust DMD-BIN  corresponding to the rank which

has been read. (on the main board)

      Rank / setting value
          B    /   0
          C    /   1
          D    /   2
          E    /   3
*Carry out adjustment when DLP chip or PC board has

been replaced

R

G

B

1. Select the following group

and subject.
Group   : VIDEO
Subject : BRIGHT

1. Check that the value is 115.

1. Select the following group

and subject.
Group   : VIDEO
Subject : PICTURE-SUB

1. Feed the color difference

signal(480i) to INPUT1
: Y 0% brightness,
Cb and Cr 0% white pat-
terns.

2. Select the following group

and subject.
Group   : COMPO
Subject : COMPO-AUTO

1. After signal input, select COMPO-AUTO for automatic

adjustment.

1. Check that the value is 96.

1. Feed the color difference

signal(480i) to INPUT1
: Y 0% brightness,
Cb and Cr 0% white pat-
terns.

2. Select the following group

and subject.
Group   : COMPO
Subject : G-BRIGHT

1. Make adjustment so that some bits should be miss-

ing in the picture.
* refer to the following photo image

1. Feed the 50% gray pattern

signal (XGA, 60 Hz) to IN-
PUT1.

2. Select the following group

and subject.
Group     :DLP
Subjects : R1-GAIN (Red)

B1-GAIN (Blue)

1. Adjust R-1 GAIN and B1-GAIN so that x-value should

be 290 ± 3 and y-value 310 ± 3.

1. Feed the 50% gray pattern

signal (XGA, 60 Hz  to IN-
PUT1

2. Select the following group

and subject.
Group     : DLP
Subjects : S-G1-GAIN (Green)

S-B1-GAIN (Blue)

1. Adjust S-G1-GAIN and S-B1-GAIN so that x-value

should be 313 ±  and y-value 329 ± 5.

1. Feed the color difference

signal(480i) to INPUT1
: Y 0% brightness,
Cb and Cr 0% white pat-
terns.

2. Select the following group

and subject.
Group   : COMPO
Subject : CR-OFFSET

1. Reduce the CR-OFFSET value by 2 points.

1. Feed the 50% gray pattern

signal (480i, color differ-
ence signal) to INPUT1.

2. Select the following group

and subject.

Group     : DLPV
Subjects : C-R1-GAIN(Red)

C-B1-GAIN(Blue)

1. Adjust C-R1-GAIN and C-B1-GAIN so that x-value

should be 290 ± 3 and y-value should be 310 ± 3.

1. Feed the 50% gray pattern

signal (NTSC, burst signal)
to INPUT4.

2. Select the following group

and subject.
Group    : DLPV
Subjects: V-R1-GAIN (Red)

V-B1-GAIN (Blue)

1. Adjust V-R1-GAIN and V-B1-GAIN so that x-value

should be 290 ± 3 and y-value should be 310 ± 3.

1. Select the following group

and subject.
Group   : SSS
Subject : S4 (North America)

S3  (Europe/Asia/
Australia)
S5  (Japan)

1. Make the following settings.

PH50XU : S4  (to north America)
PH50X : S5  (to Japan)
Other

: S3  (to Europe/Asia/Australia)

for reference / setting

OSD language

Video-set up level

S3

English

0IRE

S4

English

7.5IRE

S5

Japanese

0IRE

1. Move lens shift position

Vertical

: Top position

Horizontal: Center

(Note)
Since the PC I/F unit is initialized with S1, do not carry out S1. The PC I/F unit is already adjusted.
When the PC I/F unit must be adjusted, in such case as S1 is carried out by mistake, adjust it according to the
followings

1. Select the following group

and subject.
Group   : SSS
Subject : S1

1. Press S3602 to enter the process mode.
2. Execute the S2 command on the SSS menu.(By S1,

all the contents of EEPROM are initialized.)

1. After signal input, select AD-AUTO for automatic

adjustment.

1. Feed the window pattern

s i g n a l   t h a t   h a s   9 2 %
(0.64Vbw) and 0% signals
(XGA/60Hz) to input 1

2. Select the following group

and subject.
Group     : A/D
Subjects : AD-AUTO

* When you can not prepare

92% signal

1. Feed the window pattern

signal that has 100%
(0.7Vbw) and 0% signals.
(XGA/60Hz) to input 1

* "MUTE" key will be change

to the factory gamma

1. Select the following group and subject.

Group     : A/D
Subjects : G-BRIGHT

2. Make adjustment so that some bits should be

missing in black area of the picture.

3. Select the following group and subject.
     Group     : A/D
     Subjects : G-D
4. Make adjustment so that some bits should be miss-

ing in white area of the picture.

5. Select the following subject.
     Subjects : R-BRIGHT
6. Make adjustment so that some bits should be miss-

ing in black area of the picture.

7. Select the following subject.
     Subjects : R-D
8. Make adjustment so that some bits should be miss-

ing in white area of the picture.

9. Select the following subject.
     Subjects : B-BRIGHT
10. Make adjustment so that some bits should be miss-

ing in black area of the picture.

11. Select the following subject.
     Subjects : B-D
12. Make adjustment so that some bits should be miss-

ing in white area of the picture.