DOWNLOAD Sharp XG-NV7XE (serv.man10) Service Manual ↓ Size: 6.84 MB | Pages: 67 in PDF or view online for FREE

Power cord

Computer cable
QCNW-5304CEZZ

Mouse control cable
for Mac
QCNW-5114CEZZ

Computer audio cable
QCNW-4870CEZZ

Mouse control
cable for IBM PS/2
QCNW-5113CEZZ

Remote control
RRMCG1531CESA

Two AA size batteries

DIN-D-sub RS-232C cable
QCNW-5288CEZZ

CD-ROM
UDSKA0010CE01

Projector operation manual
TINS-6854CEZZ

Projector quick reference
TINS-6856CEZZ

Sharp Advanced Presentation
Software operation manual
TINS-6888CEZZ

Sharp Advanced Presentation
Software quick reference
TINS-6857CEZZ

IrDA driver installation
instruction sheet
TCAUZ3045CEZZ

Mouse control
serial cable
QCNW-5112CEZZ

Remote mouse receiver
RUNTK0661CEZZ

Carrying bag
GCASN0003CESA

Lens cap
GCOVH1308CESA

Lens cap strap
UBNDT0012CEZZ

Plug the supplied power cord into the AC socket on the back of the projector.

You can connect your projector to a computer for projection of full colour computer images.

Power cord

Computer audio cable
QCNW-4870CEZZ

Computer cable
QCNW-5304CEZZ

1 Connect one end of the supplied computer cable to

the INPUT 1 port on the projector.

2 Connect the other end to the Monitor output port on the

computer. Secure the connectors by tightening the
thumb screws.

3 To use the built-in audio system, connect one end of

the supplied computer audio cable to the AUDIO INPUT
terminal on the projector.

4 Connect the other end to the Audio output terminal on

the computer.

• Before connecting, be sure to turn both the projector and the

computer off. After making all connections, turn the projector
on first. The computer should always be turned on last.

• Please read the computer’s operation manual carefully.
• Refer to pages 54 and 55 “Input Signals (Recommended

Timing)” for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may
cause some of the functions not to work.

When connecting this projector to a computer, select
“Computer/RGB” for “Signal Type” on the GUI menu. (See
page 40.)

• A Macintosh adaptor may be required for use with some

Macintosh computers. Contact your nearest Sharp Authorised
LCD Projector Dealer or Service Centre.

When connecting the projector to a compatible computer other than an IBM-PC (VGA/SVGA/XGA/SXGA/UXGA)
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more information.

When connecting this projector to a computer, select “Computer/RGB” for “Signal Type” on the GUI menu. (See page 40.)

• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
• AUDIO INPUT accepts INPUT 1 or 2 port input.

• This projector is compatible with VESA-standard DDC 1/DDC 2B when connecting to a 15-pin analog terminal

and VESA-standard DDC 2B when connecting to a 20-pin digital terminal. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.

• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.

• The DDC, Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible

computer.

Computer audio cable
QCNW-4870CEZZ

1 Connect one end of the digital cable to the INPUT 2

port on the projector.

2 Connect the other end to the corresponding termi-

nal on a computer.

3 To use the built-in audio system, connect one end

of the supplied computer audio cable to AUDIO
INPUT terminal on the projector.
Connect the other end to the Audio output terminal
on the computer.

Digital cable (sold separately)

2 To digital output terminal

Computer audio cable (3.5 mm stereo minijack cable)

To audio output terminal

1 Connect the yellow RCA connectors to the corresponding

yellow VIDEO INPUT terminal on the projector and the Video
output terminal on the video source.

2 To use the built-in audio system, connect the red and white

RCA connectors to the corresponding red and white AUDIO
INPUT terminals on the projector and the Audio output
terminals on the video source.

The S-VIDEO INPUT terminal uses a video signal system in which
the picture is separated into a colour and a luminance signal to
realise a higher-quality image.

• For higher quality video, you may use the S-VIDEO INPUT terminal on

the projector. S-video cable is sold separately.

• If your video equipment does not have an S-video output terminal, use

the Composite video output terminal.

You can connect your projector to a VCR, laser disc player, DVD player, DTV decoder and other audiovisual
equipment.

• Always turn off the projector while connecting to video equipment, in order to protect both the projector and the equipment

being connected.

1 Video cable (sold separately)

S-video cable (sold separately)

2 Audio cable (sold separately)

To S-video output terminal

To video output terminal

To audio output terminals

Computer audio cable
QCNW-4870CEZZ

1 Connect one end of the HD-15-RGB cable to the INPUT 1

port on the projector.

2 Connect the other end to the corresponding terminals on the

video source.

3 To use the built-in audio system, connect one end of the

supplied computer audio cable to AUDIO INPUT terminal on
the projector.
Connect the other end to the Audio output terminal on the
video source.

Select “Computer/RGB” or “Component” for “Signal Type” on
the GUI menu, depending on the video source.

HD-15-RGB cable (sold separately)

2 To video input terminals

To audio output terminal

Computer audio cable (3.5 mm stereo minijack cable)