Sharp XG-MB67X (serv.man3) Service Manual ▷ View online
XG-MB67X
8 – 9
RGB and component signal
check
check
Send component signal or
RGB signal of 1080i (or 720P)
from INPUT 1 or INPUT 2.
Select INPUT 1 or INPUT 2
using keys on the main unit or
the remote control.
RGB signal of 1080i (or 720P)
from INPUT 1 or INPUT 2.
Select INPUT 1 or INPUT 2
using keys on the main unit or
the remote control.
YES
Is image displayed normally?
YES
End
NO
Are picture signals sent to
TL3201, TL3204, and
TL3205?
TL3201, TL3204, and
TL3205?
NO
Check IC3002 and the peripheral
circuits (check IC3052 for INPUT
2).
circuits (check IC3052 for INPUT
2).
YES
Is 3.3V applied to TL1792?
NO
Check IC1792 and peripheral cir-
cuits.
cuits.
YES
Is 3.3V applied to TL1762?
NO
Check IC1763 and peripheral cir-
cuits.
cuits.
YES
Check IC3201 and peripheral
circuits.
circuits.
XG-MB67X
8 – 10
S-VIDEO (INPUT 3)
check
check
VIDEO (INPUT 4)
check
check
Send S-Video signal
(color signal) from
INPUT 3. Select INPUT
3 using keys on the
main unit or the remote
control.
(color signal) from
INPUT 3. Select INPUT
3 using keys on the
main unit or the remote
control.
Send VIDEO signal from
INPUT 4. Use buttons
on the main unit or the
remote control to select
INPUT 4.
INPUT 4. Use buttons
on the main unit or the
remote control to select
INPUT 4.
Is image displayed nor-
mally?
mally?
YES
End
Is image displayed nor-
mally?
mally?
YES
End
NO
NO
Is image displayed in
black and white?
black and white?
YES
Check S-VIDEO ter-
minal and peripheral
circuits of Q3311.
minal and peripheral
circuits of Q3311.
Is VIDEO signal sent to
C3326?
C3326?
NO
Check VIDEO termi-
nal and peripheral cir-
cuits of Q3321.
nal and peripheral cir-
cuits of Q3321.
NO
YES
Is S-VIDEO signal (Y)
sent to R3306?
sent to R3306?
NO
Check S-VIDEO ter-
minal and peripheral
circuits of Q3301.
minal and peripheral
circuits of Q3301.
Is 1.8 V applied to
TL3358?
TL3358?
NO
Check IC3352 and
peripheral circuits.
peripheral circuits.
YES
YES
Is 1.8 V applied to
TL3358?
TL3358?
NO
Check IC3352 and
peripheral circuits.
peripheral circuits.
Is 3.3 V applied to
TL1792?
TL1792?
NO
Check IC1792 and
peripheral circuits.
peripheral circuits.
YES
YES
Is 3.3 V applied to
TL1792?
TL1792?
NO
Check IC1792 and
peripheral circuits.
peripheral circuits.
Is 1.5 V applied to
TL1762?
TL1762?
NO
Check IC1763 and
peripheral circuits.
peripheral circuits.
YES
YES
Is 1.5 V applied to
TL1762?
TL1762?
NO
Check IC1763 and
peripheral circuits.
peripheral circuits.
Check IC3351 and
peripheral circuits.
peripheral circuits.
YES
Check IC3351 and
peripheral circuits.
peripheral circuits.
XG-MB67X
8 – 11
Checking the LAN
LAN communication is disabled even
though connecting the control PC with a
LAN cable. The LINK LED (green) does not
light up.
though connecting the control PC with a
LAN cable. The LINK LED (green) does not
light up.
YES
Are the connection of connecting cable and
the settings of IP address, sub-net address
and default gateway correct?
the settings of IP address, sub-net address
and default gateway correct?
NO
Check the connecting cable and LAN settings. If the LAN
settings are unknown, contact the network administrator.
If the network settings cannot be saved, replace IC8003
(EEP ROM) as it may be defective.
settings are unknown, contact the network administrator.
If the network settings cannot be saved, replace IC8003
(EEP ROM) as it may be defective.
YES
Note: When IC8003 (EEP ROM) is replaced, the MAC
address returns to default. Refer to "Resetting after replac-
ing IC8003 (EEP ROM)" to reset.
address returns to default. Refer to "Resetting after replac-
ing IC8003 (EEP ROM)" to reset.
Are the network device (e.g. Hub) between
the control PC and XG-MB67X and cable
normal?
the control PC and XG-MB67X and cable
normal?
NO
Repair defective parts in the network.
YES
When data is sent from the control PC, do
pins (30) and (31) of IC8201 (PHY receiver)
receive signals?
pins (30) and (31) of IC8201 (PHY receiver)
receive signals?
NO
Check the peripheral circuit of J8201 (RJ-45 jack with built-
in transformer).
in transformer).
YES
Check the PHY receiver IC8201 and the
peripheral circuits of the microprocessor
IC8001.
peripheral circuits of the microprocessor
IC8001.
XG-MB67X
8 – 11
Checking the LAN
LAN communication is disabled even
though connecting the control PC with a
LAN cable. The LINK LED (green) does not
light up.
though connecting the control PC with a
LAN cable. The LINK LED (green) does not
light up.
YES
Are the connection of connecting cable and
the settings of IP address, sub-net address
and default gateway correct?
the settings of IP address, sub-net address
and default gateway correct?
NO
Check the connecting cable and LAN settings. If the LAN
settings are unknown, contact the network administrator.
If the network settings cannot be saved, replace IC8003
(EEP ROM) as it may be defective.
settings are unknown, contact the network administrator.
If the network settings cannot be saved, replace IC8003
(EEP ROM) as it may be defective.
YES
Note: When IC8003 (EEP ROM) is replaced, the MAC
address returns to default. Refer to "Resetting after replac-
ing IC8003 (EEP ROM)" to reset.
address returns to default. Refer to "Resetting after replac-
ing IC8003 (EEP ROM)" to reset.
Are the network device (e.g. Hub) between
the control PC and XG-MB67X and cable
normal?
the control PC and XG-MB67X and cable
normal?
NO
Repair defective parts in the network.
YES
When data is sent from the control PC, do
pins (30) and (31) of IC8201 (PHY receiver)
receive signals?
pins (30) and (31) of IC8201 (PHY receiver)
receive signals?
NO
Check the peripheral circuit of J8201 (RJ-45 jack with built-
in transformer).
in transformer).
YES
Check the PHY receiver IC8201 and the
peripheral circuits of the microprocessor
IC8001.
peripheral circuits of the microprocessor
IC8001.