DOWNLOAD Sharp XG-C68X Service Manual ↓ Size: 1.09 MB | Pages: 60 in PDF or view online for FREE

25

This is the physical component within the projector that creates the image. It can be either an
LCD panel or DMD device.

Calculating Image Size and Throw Distance using Focal Length 
If the throw ratio of the lens is not available then the focal length can be used to calculate the
image size or throw distance, however the dimensions of the display panel are needed.

To calculate the throw distance for a pre-defined image size:

Example
Calculate the throw distance required to give a 2.5m diagonal image. The focal length of the
lens is 44mm and the DMD panel is 20.32mm (Diag)

To calculate the image size from a set distance:

Example
Calculate the image size (diag) at a throw distance of 3m. Focal length is 63.8mm and the
LCD panel is 63.8mm (Diag)

f Focal Length

Display Device

Screen

Focus
Lens

Zoom
Lens

       44mm 

             x 

2500mm (diag)  =  5413mm  (5.413m)

20.32mm (diag)

 

3000mm 

        x      33.25mm (diag)  =  1563mm  (diag)  (1.563m)

63.8mm (diag)

Image and Panel Size must be of the same dimension. i.e. Image and Panel

diagonal measurement OR width measurement.

26

Note

• 

This projector may not be able to display images from notebook computers in simultaneous
(CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output
the display data in “CRT only” mode. Details on how to change display modes can be found in your
notebook computer’s operation manual.

• 

When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the
screen.

• 

When receiving 1,600 × 1,200 VESA format signals, sampling occurs and part of the image may be
cut as the image is displayed in 1,024 lines.

• 

Multiple signal support
Horizontal Frequency: 15–126 kHz, Vertical Frequency: 43–200 Hz*, Pixel Clock: 12–230 MHz

• 

Compatible with sync on green and composite sync signals

• 

UXGA and SXGA compatible in advanced intelligent compression

• 

AICS (Advanced Intelligent Compression and Expansion System) resizing technology

9

9

Native

8

9

9

9

9

9

9

9

“Plug and Play” function (when connecting to a 15-pin
terminal)
• 

This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a
VESA DDC compatible computer will communicate their setting requirements, allowing
for quick and easy set-up.

• 

Before using the “Plug and Play” function, be sure to turn on the projector first and the
connected computer last.

Note

• 

The DDC “Plug and Play” function of this projector operates only when used in
conjunction with a VESA DDC compatible computer.

PAL

-

-

9

PAL-60

-

-

9

SECAM

-

-

9

NTSC

-

-

9

480I

15.7

60

9

480P

31.5

60

9

540P

33.8

60

9

580I

15.6

50

9

580P

31.3

50

9

720P

45.0

60

9

1035I

33.8

60

9

1080I

33.8

60

9

1080I

28.1

50

9

27

INPUT 1/2 RGB and OUTPUT Signal Terminal: 15-pin Mini D-sub female connector

1. Video input (red)

1. PR (CR)

2. Video input (green/sync on green)

2. Y

3. Video input (blue)

3. PB (CB)

4. Reserve input 1

4. Not connected

5. Not connected

5. Not connected

6. Earth (red)

6. Earth (PR)

7. Earth (green/sync on green)

7. Earth (Y)

8. Earth (blue)

8. Earth (PB)

9. Not connected

9. Not connected

10. GND

10. Not connected

11. GND

11. Not connected

12. Bi-directional data

12. Not connected

13. Horizontal sync (Composite sync)

13. Not connected

14. Vertical sync signal

14. Not connected

15. Data clock

15. Not connected

RS-232C Terminal: 9-pin Mini DIN female connector

1

Output

Not connected

2

RD

Receive Data

Input

Connected to internal circuit

3 

SD 

Send Data 

Output

Connected to internal circuit

4 

Input 

Not connected

5 

SG 

Signal Ground 

Connected to internal circuit

6 

Input 

Not connected

7 

Output 

Not connected

8 

Input 

Not connected

9 

Output 

Not connected

 

9-pin D-sub male connector of the DIN-D-sub RS-232C adapter

1 

CD 

Not connected

2 

RD 

Receive Data 

Input

Connected to internal circuit

3 

SD 

Send Data 

Output

Connected to internal circuit

4 

ER 

Not connected

5 

SG 

Signal Ground 

Connected to internal circuit

6 

Not connected

7 

Not connected

8 

Not connected

9 

CI 

Not connected

28

RS-232C Cable recommended connection: 9-pin D-sub female connector

Note

• 

Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin
6 on the controlling device (e.g. PC).