DOWNLOAD Sharp XG-C68X (serv.man4) Service Manual ↓ Size: 25.7 MB | Pages: 127 in PDF or view online for FREE

No.

Adjustment Items

Adjustment Conditions

Adjustment Procedures

5

Adjustment of
RGB counter-
voltage

1. Feed the counter-voltage adjust-

ment signal (XGA) prepared by the
Technical Department.

2. Select the following group and sub-

jects.
Group: OUTPUT3
Subject: RC (R), GC (G), BC (B)

1. Using the set's control switch or the

remote controller button, adjust the
settings to minimize flickers.

2. If the results are inconsistent at the

center and on both sides onscreen,
readjust the settings to get the same
results on both sides.

6

Adjustment of
RGB gradation
reproduction

1. Feed the SMPTE pattern signal

(XGA) .

2. Select the following group and sub-

ject.
Group: OUTPUT1
Subject: G1-BLK

1. Confirm that the 100% and 95% white

gradation as well as the 0% and 5%
black gradation are discernible.

2. If the white gradation looks differently,

finely adjust the G1-BLK setting.

7

Adjustment of
RGB white bal-
ance

1. Feed the 32-step gray scale signal

(XGA, 60 Hz).

2. Select the following group and sub-

jects.
Group: OUTPUT1
Subjects: R1-BLK (R), B1-BLK (B)

1. Adjust the R1-BLK and B1-BLK set-

tings to have the specified gradation
balance (according to the standard
monitor).

8

Adjustment of
video AGC

1. Feed the NTSC 10-step gray scale

signal(with burst).

2. Select the following group and sub-

ject.
Group: VIDEO
Subject: AGC-ADJ

3. Connect the oscilloscope between

TP4501 and TP4502

1. Using the set's control switch or the

remote controller button, adjust the
setting so that the white-to-black level
is 0.72 Vp-p±0.01 V.

9

Adjustment of
video brightness/
contrast

1. Feed the NTSC100% window pat-

tern signal(with burst).

2. Select the following group and sub-

jects.
Group: VIDEO
Subject: AUTO, PICTURE/BRIGHT

1. Feed the signal. Using the set's con-

trol switch or the remote controller
button, select the subject AUTO. The
setting will adjust itself.

2. And then lower the adjustment value

of the PICTURE/BRIGHT by 2 points.

3. Then adjust the PICTURE/BRIGHT

setting until the signal becomes bit-
less.

10

Adjustment of
video tint

1. Feed the split color bar signal.
2. Select the following group and sub-

ject.
Group: VIDEO1
Subject: TINT

1. Confirm the fixed value.

Fixed value: 128

No.

Adjustment Items

Adjustment Conditions

Adjustment Procedures

11

Adjustment of
NTSC color
saturation

1. Feed the split color bar signal.
2. Select the following group and sub-

ject.
Group: VIDEO
Subject: N-COLOR

~

Connect the oscilloscope to pin (1)
of P1301.

1. Confirm the fixed value.

Fixed value: 54
(Reference: 0.4 Vp-p)

12

Adjustment of PAL
color saturation

1. Feed the PAL color bar signal.
2. Select the following group and sub-

ject.
Group: VIDEO
Subject: P-COLOR

~

Connect the oscilloscope to pin (1)
of P1301.

1. Confirm the fixed value.

Fixed value: 51
(Reference: 0.4 Vp-p)

13

Adjustment of
SECAM color
saturation

1. Feed the SECAM color bar signal.
2. Select the following group and sub-

ject.
Group: VIDEO
Subject: S-COLOR

~

Connect the oscilloscope to pin (1)
of P1301.

1. Confirm the fixed value.

Fixed value: 48
(Reference: 0.5 Vp-p)

14

Adjustment of
video white bal-
ance

1. Feed the NTSC monoscope pattern

signal(with burst).

2. Select the following group and sub-

jects.
Group: VIDEO
Subjects: V-R1-BLK, V-B1-BLK

1. Using the set's control switch or the

remote controller button, adjust the
settings to have the same white bal-
ance as on the standard monitor.

16

Adjustment of
COMPO bright-
ness

1. Feed the 0% gray pattern signal

(480I).

2. Select the following group and sub-

ject.
Group: COMPO
Subject: G-BRIGHT

1. Adjust so that pixel defect occurs on

the screen.

100% White Red

100% White Red

100% White Red

15

Adjustment of
COMPO CB offset
and CR offset

1. Feed the Y-0% brightness, Cb and

Cr 0% white pattern color difference
signal (480I).

2. Select the following group and sub-

ject.
Group: COMPO
Subject: AUTO

1. Feed the signal. Using the set's con-

trol switch or the remote controller
button, select the subject AUTO. The
setting will adjust itself.

No.

Adjustment Items

Adjustment Conditions

Adjustment Procedures

17

Adjustment of
COMPO white
balance

1. Feed the DTV monoscope pattern

signal.

2. Select the following group and sub-

jects.
Group: COMPO
Subjects: C-R1-BLK, C-B1-BLK

1. Using the set's control switch or the

remote controller button, adjust the
settings to have the same white bal-
ance as on the standard monitor.

20

Adjustment of
sRGB white
balance

1. Feed the RGB 50% gray pattern

signal.

2. Select the following group and sub-

jects.
Group: OUTPUT1
Subjects: S-R1-BLK, S-R1-GAIN, S-
G1-BLK, S-G1-GAIN, S-B1-BLK, S-
B1-GAIN

3. Have the BM-5 brightness meter and

the standard white board at hand.

1. Make the S-R1-GAIN setting the

same as the R1-GAIN one.
Make the S-G1-GAIN setting the
same as the R1-GAIN one.
Make the S-B1-GAIN setting the
same as the R1-GAIN one.
Make the S-R1-BLK setting the same
as the R1-BLK one.

2. Adjust the S-B1-BLK and S-G1-BLK

settings so that the chromaticity on
the brightness meter should be as
follows.
x: .313±7/1000
y: .350±10/1000

18

Automatic color
irregularity correc-
tion

1. Apply the automatic color correc-

tion using the automatic color irregu-
larity correction system (ccdc).

1. Make sure that no remarkable uneven

color remains on the screen.

19

Checking of
tracking

1. Input the RGB 10-step gray-scale

(inverse vertically) signal.

2. Select the following group and sub-

ject.
Group: LINE
Subject: OPT-MECH

Check the tracking of the gradation on
the lower side.
In case that it is bad, adjust the OPT-
MECH value to the optimum.
(It takes 2 - 3 seconds for changing for
selection.)
0:Red and blue up
1:Red and blue down
2:Initial value (Normal)

The following measurement and adjustment must be carried out:

• In a dark room (take care for stray light)

• Using diffuse reflection type (mat type) screen in the uniform conditions.

Settings of the projector must be carried out in the following conditions:

• Do not save power (to keep the lamp to the stable condition during measurement)

• Automatic search cancel (to fix INPUT1)

• INPUT1 RGB mode (cancel the component mode of INPUT 1, just in case)

(1) System setting (“setting” - “system setting”)

System optional

Simultaneous write in of 3D correction value:

No (not checked)

Char transmission interval:

0 ms

Binary interval:

2 ms

Creation of correction value by straight-line

correction coefficient:

No (not checked)

Number of image captures (when adjustment,

measurement):

2 times

Number of image captures (when teaching):

4 times

(2) Teaching

Basically only one time measurement is necessary for each model for teaching, however when the optical

characteristics, etc. of the set are greatly changed, set the conditions again and measurement is neces-

sary again according to the changes.

Measurement method of the correction coefficient

(1) Determines the standard set of C55. 1 unit (n units)

(2) Set settings are RGB mode INPUT 1.

(3) Execute teaching in the following condition setting in that standard set.

Condition setting

Model name:

Newly input the model name and optical characteris-

tics Var.

Resolution:

(Not related)

Correction value X direction:

29

Correction value Y direction:

22

Correction bits number:

8

Minimum adjustment value:

0

Center adjustment value:

36

Maximum adjustment value:

73

Teaching number:

5

Teaching interval:

18

Brightness change direction by adjustment value: Brightness up with adjustment value + (checked)

Adjusting points:

3-dimension (checked)

Gradation 4 (checked)

Gradation 5 (checked)

Gradation 6 (checked)

Do not check the gradations other than these.

Adjusting point (Test pattern display level)

Gradation 7:

91%

Gradation 6:

78%

Gradation 5:

65%

Gradation 4:

52%

Gradation 3:

40%

Gradation 2:

25%

Gradation 1:

13%

Gradation 0:

0%

Adjustment color:

Adjustment with WHITE (checked)

(3) Color irregularity correction

Conditions setup

Correction procedure settings

Gradation 7:

2. Lower-gradation correction value to be used.

Gradation 6:

0. Correction with correction coefficient.

Gradation 5:

0. Correction with correction coefficient.

Gradation 4:

0. Correction with correction coefficient.

Gradation 3:

1. Upper-gradation correction value to be used.