DOWNLOAD Sharp XG-C465X (serv.man4) Service Manual ↓ Size: 1.84 MB | Pages: 15 in PDF or view online for FREE

XG-C435X/C465X

3 – 9

The following measurement and adjustment must be performed under the same conditions using the following:

• Dark room (Block out stray light.)

• Diffuse reflection (mat type) screen

The setting of the projector must be performed under the following conditions:

• Power save disabled (to keep the lamp stable during measurement)

• Auto search canceled (to fix to INPUT1)

• RGB mode of the input terminal COMPUTER1 (component mode canceled - just to be sure)

1. System setting (“Setting -” System setting””)

Condition setting for C435/C465

2. Teaching

Basically, teaching should be measured only once from model to model. However, if the optical characteristics of the set are changed significantly,
it is necessary to reset the conditions according to changes and to perform remeasurement.

Measurement method of correction factor

1) Determine the standard set of C435/C465. Each one unit (n units)

2) Switch the set to the RGB mode of the input terminal COMPUTER1.

3) Execute teaching of the standard set under the following conditions.

Condition setting for C435/C465

    System option
    Simultaneous writing of 3D correction value:

No (not checked)

    Char transmission interval:

0 ms

    Binary interval:

2 ms

    Creation of correction value by linear correction factor:

No (not checked)

    Number of image captures (during adjustment or measurement): Twice
    Number of image captures (during teaching):

4 times

    Model name:

Enter the model name newly.

    Resolution:

1024 x 768

    Binary interval:

2 ms

    Correction value, X direction:

33

    Correction value, Y direction:

25

    Number of correction bits:

8

    Adjustment value, minimum:

-32

    Adjustment value, center:

0

    Adjustment value, maximum:

32

    Number of teachings:

5

    Teaching interval:

32

    Brightness variation direction by adjustment value: Brightness UP by increasing the adjustment value (checked)
    Adjustment point:

3D (checked)
TG system (selected)
Tone 0 (checked)
Tone 1 (checked)
Other tones are not checked.

    Adjustment point (Test pattern display level)
    Tone 0:

44%

    Tone 1:

64%

    Adjustment color:

Adjustment with RGB (checked)

XG-C435X/C465X

3 – 10

3. Color shading correction (adjustment)

Condition setting for C435/C465

Correction method

Select the model name created in the section (2) and perform color shading correction/adjustment.

If the set has significantly different optical characteristics from the standard or shows color shading or line dropouts, execute teaching and adjust it
using the correction factor.

    Correction setting
    Tone 7:

Default

    Tone 6:

Default

    Tone 5:

Default

    Tone 4:

Default

    Tone 3:

Default

    Tone 2:

Default

    Tone 1:

Correction by correction factor

    Tone 0:

Correction by correction factor

17

DTV bright/contrast 
adjustment

1) Select the following.

Group: DTV
Adjustment item: Contrast
                            Bright

1) Check the fixed values.

Contrast: 10
Bright: 40

18

DTV tint adjustment

1) Select the following.

Group: DTV
Adjustment item: Tint

1) Check the fixed value.

Tint: 5

19

TV color saturation 
adjustment

1) Select the following.

Group: DTV
Adjustment item: Color

1) Check the fixed value.

Color: 12

20

DVD bright/contrast 
adjustment

1) 1. Select the following.

Group: DVD
Adjustment item: Contrast
                            Bright

1) Check the fixed values.

Contrast: 9
Bright: 40

21

DVD tint adjustment

1) Select the following.

Group: DVD
Adjustment item: Tint

1) Check the fixed value.

Tint: 5

22

DVD color saturation 
adjustment

1) Select the following.

Group: DVD
Adjustment item: Color

1) Check the fixed value.

Color: 12

23

Video bright/contrast 
adjustment

1) Select the following.

Group: VIDEO
Adjustment item: Contrast
                            Bright

1) Check the fixed values.

Contrast: 8
Bright: 40

24

Video tint adjustment

1) Select the following.

Group: VIDEO
Adjustment item: N-Tint
                            P-Tint
                            S-Tint

1) Check the fixed values.

N-Tint: 5
P-Tint: 5
S-Tint: 5

25

Video color saturation 
adjustment

1) Select the following.

Group: VIDEO
Adjustment item: N-Color
                            P- Color
                            S- Color

1) Check the fixed values.

N-Color: 6
P- Color: 6
S- Color: 6

26

RGB tone reproduction 
adjustment

1) Input the SMPTE pattern.
2) Group: OUTPUT1

Adjustment item: G1-BLK

1) Check that white 100% and 95% tones are visible.
2) If visibility of the white tones is different, fine adjust G1-BLK.

XG-C435X/C465X

3 – 11

27

White balance check

RGB input, sRGB input, component input, 
video input, S-video input

1) Check that there is no disturbance in the white balance using a 

monitor.

28

Vertical stripe level 
check

1) Receive the RGB gray scale signal.

1) It must be better than the vertical stripe boundary sample.

29

Checking of off-timer 
performance

1) Select  OFF in the process mode.

Make sure that the off-timer starts with 5-minute display, counts 
down 1minute for 1second, and turns off when 0minute is dis-
played.

30

Checking of ther-
mistor performance

1) Heat the thermistor with a hair dryer.

1) Make sure the temperature is displayed.

31

Automatic sync opera-
tion

1) Receive the phase checking pattern 

signal.

1) Make sure that Clock, Phase, H-POS and V-POS can be automat-

ically adjusted in the VGA/S-VGA/XGA mode.

32

Monitor out check

1) Input the video and audio signals to the 

COMPUTER1 and COMPUTER2 ter-
minals.

2) Connect another monitor to the monitor 

out terminal.

3) Connect a speaker with a built-in ampli-

fier to the audio out terminal.

1) Check that image selected with the projector is displayed on 

another monitor connected to monitor out terminal and sound is 
heard from the speaker connected to the audio out terminal.

33

RS232C operation 
check

1) Connect the unit and a PC with the 

RS232C cable.

1) Send a command from the PC, and check it functions correctly.

34

USB operation check

1) Connect to a PC with an USB cable.

1) Check that forward/reverse operation is enabled on the PC screen 

using the remote control.

35

LAN operation check

1) Connect to a PC with a LAN cable.

1) Check that communication is possible.

36

Remote control check

1) Check the wired remote operation.
2) Check the remote control operation.

1) Check that the wired remote control terminal is activated.
2) Check the remote control operation.

37

Model name check

1) Send “TNAM 1” and “MNRD 1”h with 

RS232C command.

1) Check that the appropriate model name is displayed correctly.

38

Delivery settings

1) Make the following settings.

Destination

Process

Remote control

adjustment

adjustment

USA

SS4

Factory setting at 4

Others

SS3

Factory setting at 3

ON ENTER ENTER

PLUS

MINUS

(Adj Right)

(Adj Left)

XG-C435X/C465X

3 – 12

Adjustment mode process menu

Adjust DTV image

DTV

Contrast
Tint
Color
Sharpness
Bright
B-DRIVE
R-DRIVE

Adjust DVD image

DVD

Contrast
Tint
Color
Sharpness
Bright
B-DRIVE
R-DRIVE

Adjust Video image

VIDEO

Contrast
N-Tint
P-Tint
S-Tint
N-Color
P-Color
S-Color
Sharpness
Bright
B-DRIVE
R-DRIVE

Adjust PC image

AD

R-Bright
G-Bright
B-Bright
R-Contrast
G-Contrast
B-Contrast

Adjust PC image

AD2

R-Bright2
G-Bright2
B-Bright2
R-Contrast2
G-Contrast2
B-Contrast2

Adjust RGB image

OUTPUT1

R1-BLK
R1-GAIN
G1-BLK
G1-GAIN
B1-BLK
B1-GAIN
TGR-BLK
TGR-GAIN
TGG-BLK
TGG-GAIN
TGB-BLK
TGB-GAIN
R-COM
G-COM
B-COM
R-COM2
G-COM2
B-COM2
COM-LEVEL
S-R1-BLK
S-G1-BLK
S-B1-BLK

Adjust Panel

OUTPUT2

LC-SW
LC-HPOS-R
RLV1
RLV1