DOWNLOAD Sharp XG-C455W (serv.man6) Service Manual ↓ Size: 1.45 MB | Pages: 15 in PDF or view online for FREE

XG-C455W/PG-C355W

4 – 9

1

EEPROM initialization

1)  Turn on the power (the lamp turns on) 

and perform aging for 15 minutes.

1) Perform the following setting.

Press S6501 to enter the process mode, and execute SS2 of the 
SS menu.

2

Model setting

(Process menu)
1) Select the following.

Group: MODEL
Adjustment item: MODEL-SELECT

1) Series bellow

XG-C455W: 0
PG-C355W: 1

3

R-bright check
Contrast adjustment 
(manual or automatic)

1) Input the white/black wind pattern sig-

nal of amplitude level 96% (0.67 Vpp)/
0% of  XGA60Hz to COMPUTER1.

2) Select the following.

Group: AD
Adjustment item:R-Bright
                           R-Contrast

(Process gamma linkage)

1) Check the fixed value.

R-Bright: 125

2) Observe the chromaticity of 96% white wind pattern portion using 

CA100.

3) On the screen where bit dropouts occur, raise the R-Contrast 

value. Adjust to the point where black to bright red bit dropouts 
occur and the x value changes by 30/1000 or more.

4

G-bright check
Contrast adjustment 
(manual or automatic)

1) Input the white/black wind pattern sig-

nal of amplitude level 96% (0.67 Vpp)/
0% of  XGA60Hz to COMPUTER1.

2) Select the following.

Group: AD
Adjustment item: G-Bright
                            G-Contrast

(Process gamma linkage)

1) Check the fixed value.

G-Bright: 125

2) Observe the chromaticity of 96% white wind pattern portion using 

CA100.

3) On the screen where bit dropouts occur, raise the G-Contrast 

value. Adjust to the point where black to bright green bit dropouts 
occur and the y value changes by 30/1000 or more.

5

B-bright check
Contrast adjustment 
(manual or automatic)

1) Input the white/black wind pattern sig-

nal of amplitude level 96% (0.67 Vpp)/
0% of  XGA60Hz to COMPUTER1.

2) Select the following.

Group: AD
Adjustment item: B-Bright
                            B-Contrast

(Process gamma linkage)

1) Check the fixed value.

B-Bright: 125

2) Observe the chromaticity of 96% white wind pattern portion using 

CA100.

3) On the screen where bit dropouts occur, raise the B-Contrast 

value. Adjust to the point where black to bright blue bit dropouts 
occur and the y value changes by 30/1000 or more.

6

Black level/amplitude 
adjustment of LCD 
panel input signal

1) Select the following.

Group: OUTPUT 1
Adjustment item: G1-BLK
                            G1-GAIN
                        R: R1-BLK
                             R1-GAIN
                        B: B1-BLK
                             B1-GAIN

2) Check that the white pattern for pro-

cess adjustment is displayed.

3) Connect a synchroscope to 2P of 

(P1401).

4) For red and blue, connect to (P1401-

1P) and (P1401-3P) respectively.

1) Select G1-GAIN, and adjust the signal amplitude as follows using 

the operation SW or button on the remote control (see figure (1) 
below).
4.6 Vpp 

± 0.05 V

2) Select G1-BLK, and adjust the white-white level as follows using 

the operation SW or button on the remote control (see figure (2) 
below).
0.8 Vpp 

± 0.1 V

3) Adjust red and blue in the same way.

(G waveform diagram of process pattern)

* The part defining the amplitude to the waveform is the same for both 
R and B.

7

Sample-hold pulse 
delay amount adjust-
ment

1) Input the black signal of XGA mode.
2) Select the following.

Group: OUTPUT3
Adjustment item: ENBR-DLY
                       G: ENBG-DLY
                       B: ENBB-DLY

1) Check the blur and ghost of characters of OUTPUT3.
2) Raise the ENBR-DLY value until pre-ghost appears on the left of 

characters of OSD.

3) When the value is reduced by 1 to 2 points, pre-ghost disappears. 

Set to the value reduced by 3 from the value where pre-ghost dis-
appears.
(Set to 8 in the following case: When the ENBR-DLY value is 20, 
pre-ghost appears; when it is 13, pre-ghost disappears.)

4) Adjust green and blue in the same way.
5) When vertical strips is visible, adjust ENBXG-PH (0 to 3)

NOTE: EPSON panels may vary by 1 to 2 points from lot to lot. To 

improve the ghost quality, perform this adjustment.

White-white (2)

Amplitude (1)

XG-C455W/PG-C355W

4 – 10

The following measurement and adjustment must be performed under the same conditions using the following:

• Dark room (Block out stray light.)

• Diffuse reflection (mat type) screen

The setting of the projector must be performed under the following conditions:

• Power save disabled (to keep the lamp stable during measurement)

• RGB mode of the input terminal COMPUTER1 (component mode canceled - just to be sure)

1. System setting (“Setting -” System setting””)

Condition setting for PG-C355W/XG-C455W

2. Teaching

Basically, teaching should be measured only once from model to model. However, if the optical characteristics of the set are changed significantly,
it is necessary to reset the conditions according to changes and to perform remeasurement.

Measurement method of correction factor

1) Determine the standard set of PG-C355W/XG-C455W. Each one unit (n units)

2) Switch the set to the RGB mode of the input terminal COMPUTER1.

8

RGB counter voltage 
adjustment

1) Input the counter voltage adjustment 

signal. (XGA)

2) Select the following.

Group: OUTPUT1
Adjustment item: R-COM
                            G-COM
                            B-COM
                            R-COM2
                            G-COM2
                            B-COM2

1) Adjust flicker using the operation SW or button on the remote con-

trol so that it becomes minimum.

2) When flicker appears on the screen unevenly, adjust the center 

area considering the whole balance.

9

RGB white balance 
adjustment

1) Input the RGB 50% gray signal. 

(XGA60Hz)

2) Select the following.

Group: OUTPUT1
Adjustment item: R1-BLK (R)
                            B1-BLK (B)

1) 1. Adjust R1-BLK and B1-BLK so that the following chromaticity 

values are obtained in the middle of the screen using CL200.
x = 294 

± 5, y = 327 ± 5

10

sRGB white balance 
adjustment

1) Input the RGB 50% gray signal.
2) Select the following.

Group: OUTPUT1
Adjustment item: S-G1-BLK
                            S-B1-BLK

1) Adjust S-G1-BLK and S-B1-BLK so that the following chromaticity 

values are obtained in the middle of the screen using CL200.
x = 322 

± 5, y = 341 ± 5

11

Auto keystone initial-
ization

1) Select the following.

Group: LINE
Adjustment item: Calibration

1) With the set placed on a level surface, press the ENTER key and 

check that K-Sensor value is 0 

± 3.

Check that keystone is caused by tilting the unit.

12

Tracking check

1) Input the RGB 10-step gray scale sig-

nal (inversion on top and bottom).

2) Select the following.

Group: OUTPUT3
Adjustment item: GAMMA

1) Check the lower gradation tracking.

When it is improper, optimize the GAMMA value.
1: Default (normal)
2: Green up
3: Red and blue up
4: Green up
5: Red up and blue down
6: Blue up
7: Red and green up
8: Green and blue up

NOTE: When changing the GAMMA value, readjust the white bal-

ance.

13

Auto color shading 
correction

1) Perform the auto color shading correc-

tion using the color shading correction 
system (ccdc).

1) Check that remarkable color shading is not found on the screen.

    System option
    Simultaneous writing of 3D correction value:

No (not checked)

    Char transmission interval:

0 ms

    Binary interval:

2 ms

    Creation of correction value by linear correction factor:

No (not checked)

    Number of image captures (during adjustment or measurement): Twice
    Number of image captures (during teaching):

4 times

XG-C455W/PG-C355W

4 – 11

3) Execute teaching of the standard set under the following conditions.

Condition setting for PG-C355W/XG-C455W

3. Color shading correction (adjustment)

Condition setting for C355W/C455W

Correction method

Select the model name created in the section (2) and perform color shading correction/adjustment.

If the set has significantly different optical characteristics from the standard or shows color shading or line dropouts, execute teaching and adjust it
using the correction factor.

    Model name:

Enter the model name newly.

    Resolution:

1280 x 800

    Binary interval:

2 ms

    Correction value, X direction:

33

    Correction value, Y direction:

25

    Number of correction bits:

8

    Adjustment value, minimum:

-48

    Adjustment value, center:

0

    Adjustment value, maximum:

48

    Number of teachings:

5

    Teaching interval:

24

    Brightness variation direction by adjustment value: Brightness UP by increasing the adjustment value (checked)
    Adjustment point:

3D (checked)
TG system (selected)
Tone 0 (checked)
Tone 1 (checked)
Other tones are not checked.

    Adjustment point (Test pattern display level)
    Tone 0:

11%

    Tone 1:

40%

    Adjustment color:

Adjustment with RGB (checked)

    Correction setting
    Tone 7:

Default

    Tone 6:

Default

    Tone 5:

Default

    Tone 4:

Default

    Tone 3:

Default

    Tone 2:

Default

    Tone 1:

Correction by correction factor

    Tone 0:

Correction by correction factor

14

Component offset 
adjustment

1) Select the following.

Group: AD
Adjustment item: C-R-OS
                            C-B-OS

1) Check the fixed values.

C-R-OS: 260
C-B-OS: 260

15

Video bright/contrast 
adjustment

1) Select the following.

Group: VIDEO
Adjustment item: V-CONT
                            V-BRIGHT

1) Check the fixed values.

V-CONT: 134
V-BRIGHT: 68

16

Video tint adjustment

1) Select the following.

Group: VIDEO
Adjustment item: V-HUE

1) Check the fixed value.

V-HUE: 128

17

Video color saturation 
adjustment

1) Select the following.

Group: VIDEO
Adjustment item: V-COLOR

1) Check the fixed value.

V-COLOR: 139

18

sRGB check

sRGB input.

1) Check that the chromaticity values are in spec. 

X=322

±5

Y=341

±5

19

Vertical stripe level 
check

1) Receive the RGB gray scale signal.

1) It must be better than the vertical stripe boundary sample.

20

Checking of off-timer 
performance

1) Select the following.

Group: LINE
Adjustment item: OFF

1) Make sure that the off-timer starts with 5-minute display, counts 

down 1minute for 1second, and turns off when 0minute is dis-
played.

XG-C455W/PG-C355W

4 – 12

1) Disabling procedure

With System-Lock input window onscreen, press the “MENU”, “ENTER”, “ENTER”, “MENU”, “ENTER”, “ENTER” and “MENU” keys, in this order,
on the remote controller.

 

21

Checking of ther-
mistor performance

1) Heat the thermistor with a hair dryer.

1) Make sure the temperature warning is displayed.

22

Automatic sync opera-
tion

1) Receive the phase checking pattern 

signal.

1) Make sure that Clock, Phase, H-POS and V-POS can be automat-

ically adjusted in the VGA/S-VGA/XGA mode.

23

DVI input operation 
check

1) Send the video signal to the DVI termi-

nal.

1) Check that an image is properly projected

24

Monitor out check

1) Input the video and audio signals to the 

COMPUTER1 and COMPUTER2 ter-
minals.

2) Connect another monitor to the monitor 

out terminal.

3) Connect a speaker with a built-in ampli-

fier to the audio out terminal.

1) Check that image selected with the projector is displayed on 

another monitor connected to monitor out terminal and sound is 
heard from the speaker connected to the audio out terminal.

25

RS232C operation 
check

1) Connect the unit and a PC with the 

RS232C cable.

1) Send a command from the PC, and check it functions correctly.

26

USB operation check

1) Connect to a PC with an USB cable.

1) Check that forward/reverse operation is enabled on the PC screen 

using the remote control.

27

LAN operation check

1) Connect to a PC with a LAN cable.

1) Check that communication is possible.

28

Remote control check

1) Check the wired remote operation.
2) Check the remote control operation.

1) Check that the wired remote control terminal is activated.
2) Check the remote control operation.

29

Model name check

1) Send “TNAM 1” and “MNRD 1”h with 

RS232C command.

1) Check that the appropriate model name is displayed correctly.

30

Delivery settings

1) Make the following settings.

Destination

Process

Remote control

adjustment

adjustment

USA

SS4

Factory setting at 4

Others

SS3

Factory setting at 3

ENTER

ENTER RIGHT LEFT ENTER

ENTER MENU