DOWNLOAD Sharp XG-C430X (serv.man2) Service Manual ↓ Size: 6.41 MB | Pages: 71 in PDF or view online for FREE

All the safety and operating instructions should be read before
the product is operated.

The safety and operating instructions should be retained for
future reference.

All warnings on the product and in the operating instructions
should be adhered to.

All operating and use instructions should be followed.

Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.

Do not use attachments not recommended by the product
manufacturer as they may cause hazards.

Do not use this product near water–for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.

Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recommended
by the manufacturer, or sold with the product. Any mounting
of the product should follow the manufacturer’s instructions,
and should use a mounting accessory recommended by the
manufacturer.

A product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.

Slots and openings in the cabinet are provided for ventilation
to ensure reliable operation of the product and to protect it
from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.

This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.

This product is provided with one of the following types of
plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.

a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a

grounding terminal.
This plug will only fit into a grounding type power
outlet.

Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.

For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the cable
system. This will prevent damage to the product due to
lightning and power-line surges.

Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.

Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.

Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.

Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into

the product.

c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following

the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.

e. If the product has been dropped or damaged in any

way.

f. When the product exhibits a distinct change in

performance, this indicates a need for service.

When replacement parts are required, ensure that the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.

Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.

This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.

This product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.

■ Potential hazard of glass par-

ticles if lamp ruptures. In case
of lamp rupture, contact your
nearest Sharp Authorized Pro-
jector Dealer or Service Cen-
ter for replacement.
See “Replacing the Lamp” on
page 

■ For minimal servicing and to maintain high

image quality, SHARP recommends that this
projector be installed in an area free from hu-
midity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more
often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by  a Sharp Authorized Projector Dealer or
Service Center.

■ Position the screen so that it is not in direct

sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.

■ Placement should be within ±9 degrees of

horizontal.

■ When you use the projector in high-altitude

areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.

■ When placing the projector in a high posi-

tion, make certain it is carefully secured to
avoid personal injury caused by the projec-
tor falling down.

■ Take  care with the lens so as not to hit or

damage the surface of the lens.

■ Continuously watching the screen for long

hours will cause eye strain. Take regular
breaks to rest your eyes.

■ The operating temperature of the projector

is from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is

from –4°F to 140°F (–20°C to +60°C).

■ Allow at least 7 

7

/

8

 inches (20 cm) of space

between the exhaust vent and the nearest
wall or obstruction.

■ Ensure that the intake vent and the exhaust

vent are not obstructed.

■ If the cooling fan becomes obstructed, a pro-

tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion (see pages 

). Remove the pro-

jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.

CAUTION

PRECAUCIÓN

PRÉCAUTION

■ When using the projector, take care not to sub-

ject it to hard impact and/or vibration, as this
can result in damage. Take extra care with the
lens. If you are not to use the projector for a
long time, make certain you unplug the power
cord from the wall outlet, and disconnect any
other cables connected to it.

■ Do not carry the projector by holding the lens.

■ When storing the projector, ensure you attach

the lens cap to the projector. (See page 

■ Do not expose the storage case or projector

to direct sunlight or near heat sources. The
storage case or projector may change color
or become deformed.

■ When connecting a computer or other audio-

visual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.

■ Please read the operation manuals of the pro-

jector and the equipment to be connected for
instructions on how to make the connections.

■ The power supply voltage and the shape of

the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.

■ If the projector starts to over-

heat due to setup problems
or blockage of the air vents,
“

” and “

” will illumi-

nate in the lower left corner of the picture. If the
temperature continues to rise, the lamp will turn
off, the temperature warning indicator on the
projector will blink, and after a 90-second cool-
ing-off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on
page 

for details.

• The cooling fan regulates the internal tem-

perature, and its performance is automati-
cally controlled. The sound of the fan may
change during projector operation due to
changes in the fan speed. This does not
indicate malfunction.

• Even if you unplug the power cord after

projector operation, the cooling fan con-
tinues to run for a while. When you place
the projector into the storage case, make
sure that the cooling fan has stopped.

Remote control
RRMCGA502WJSA

Two R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)

Power cord

*

For U.S., Canada, etc.
(6' (1.8 m))
QACCDA007WJPZ

For Europe, except U.K.
(6' (1.8 m))
QACCVA011WJPZ

*

Use the power cord that corresponds to the wall outlet in your country.

■ 3 RCA to 15-pin D-sub cable (10' (3.0 m))

AN-C3CP2

■ Remote receiver

AN-MR2

■ Lamp unit

AN-C430LP

Note

• Some of the optional accessories may not be available depending on the region. Please check with your

nearest Sharp Authorized Projector Dealer or Service Center.

(1)

(2)

(3)

(4)

DIN-D-sub RS-232C
adaptor
(5

 

57

/

64

" (15 cm))

QCNWGA015WJPZ

Lens cap (attached)
PCAPHA003WJSA

RGB cable
(10' (3.0 m))
QCNWGA045WJPZ

For U.K., Hong Kong
and Singapore
(6' (1.8 m))
QACCBA036WJPZ

For Australia, New
Zealand and Oceania
(6' (1.8 m))
QACCLA018WJPZ

Storage case
GCASNA020WJSA

Lens cap strap
UBNDTA017WJZZ

• Operation manual (this manual (TINS-C555WJZZ) and CD-ROM (UDSKAA080WJZZ))