Sharp XG-C430X (serv.man2) User Manual / Operation Manual ▷ View online
-31
Basic Operation
Image Projection
Height Adjustment button
Side View
Lens
center
center
Top View
Using the Adjustment
Feet
Feet
The height of the projector can be adjusted
using the adjustment feet when the screen is
located higher than the projector, the screen
is inclined or when the installation site is
slightly inclined.
Install the projector so that it is as perpen-
dicular to the screen as possible.
using the adjustment feet when the screen is
located higher than the projector, the screen
is inclined or when the installation site is
slightly inclined.
Install the projector so that it is as perpen-
dicular to the screen as possible.
1
Press the Height Adjustment but-
tons.
tons.
• The adjustment feet come out.
2
Lift the projector to adjust its
height and remove your hands
from the Height Adjustment but-
tons.
height and remove your hands
from the Height Adjustment but-
tons.
• The projector is adjustable up to approxi-
mately 9 degrees.
3
Rotate the Tilt dial to finely ad-
just the horizontal tilt of the pro-
jector.
just the horizontal tilt of the pro-
jector.
• The inclination is adjustable within ap-
proximately 2 degrees.
• When adjusting the height of the pro-
jector, trapezoidal distortion occurs.
When “Auto Keystone” of the “Options1”
menu is set to “On” (see page
When “Auto Keystone” of the “Options1”
menu is set to “On” (see page
48
), key-
stone correction functions automatically
to correct trapezoidal distortion. When
you want to adjust the automatically cor-
rected image, use the manual keystone
correction. (See page
to correct trapezoidal distortion. When
you want to adjust the automatically cor-
rected image, use the manual keystone
correction. (See page
32
.)
Info
• Do not press the Height Adjustment button
when the adjustment feet come out without
firmly holding the projector.
firmly holding the projector.
• Do not hold the lens when lifting or lower-
ing the projector.
• When lowering the projector, be careful not
to get your fingers caught in the area be-
tween the adjustment foot and the projector.
tween the adjustment foot and the projector.
Adjustment foot
Tilt dial
-32
Image Projection
"On-screen Display (Keystone Correction mode)
KEYSTONE
button
button
MOUSE/Adjustment
buttons ('/"/\/|)
buttons ('/"/\/|)
RETURN button
Compresses
lower side.
lower side.
Compresses
upper side.
upper side.
Note
• The Manual Keystone Correction can be ad-
justed up to an angle of approximately ±40
degrees and the screen can also be set up
to an angle of approximately ±40 degrees
(when the resize mode is set to “Normal”
(see page
degrees and the screen can also be set up
to an angle of approximately ±40 degrees
(when the resize mode is set to “Normal”
(see page
47
)).
Correcting Trapezoidal
Distortion
Distortion
Auto Keystone Correction
When the image is projected either from the top
or from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called
or from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called
Keystone Correction
.
This projector is equipped with an “Auto Keystone
Correction” function that automatically corrects
any trapezoidal distortion within the projected im-
age. The correction is made automatically provided
the vertical incline or decline is within
Correction” function that automatically corrects
any trapezoidal distortion within the projected im-
age. The correction is made automatically provided
the vertical incline or decline is within
±
12 degrees.
Note
• When not using the Auto Keystone Correc-
tion function, set “Auto Keystone” on the
“Options1” menu to “Off”.
“Options1” menu to “Off”.
Manual Keystone Correction
When you want to make fine adjustments after the
Auto Keystone Correction function has been activated,
or when you want to make corrections without using
the Auto Keystone Correction function, you can make
corrections manually using the following procedure.
Auto Keystone Correction function has been activated,
or when you want to make corrections without using
the Auto Keystone Correction function, you can make
corrections manually using the following procedure.
1
Press
KEYSTONE on the remote
control to enter the Keystone Correc-
tion mode.
tion mode.
• You can also use
KEYSTONE on the
projector.
2
Press ', | or ", \ on the re-
mote control to adjust the Key-
stone Correction.
stone Correction.
• You can also adjust the Keystone Cor-
rection using the '
'
'
'
', |
|
|
|
| or "
"
"
"
", \
\
\
\
\ buttons
on the projector.
Note
• Press
RETURN to return to the de-
fault setting.
• Straight lines or the edges of images may
appear jagged while adjusting the image.
3
Press
KEYSTONE.
• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use
KEYSTONE on the
projector.
-33
Basic Operation
Adjusting the Lens
The image is focused and adjusted to the screen
size using the focus ring or zoom knob on the
projector.
size using the focus ring or zoom knob on the
projector.
1
The focus is adjusted by rotat-
ing the focus ring.
2
Zooming is adjusted by moving
the zoom knob.
Focus ring
Zoom knob
Zoom in
Zoom out
-34
Image Projection
Switching the INPUT
Mode
Mode
Select the appropriate input mode for the con-
nected equipment.
nected equipment.
On the remote control
Press
,
,
,
or
on the
remote control to select the input mode.
On the projector
1
1
1
1
1 Press an INPUT ('
'
'
'
'/"
"
"
"
") button.
• The INPUT list appears.
2
2
2
2
2 Press '
'
'
'
'/"
"
"
"
" to select an item on
the list.
3
3
3
3
3 Press ENTER.
Note
• When no signal is received, “NO SIGNAL”
will be displayed. When a signal that the
projector is not preset to receive is received,
“NOT REG.” will be displayed.
projector is not preset to receive is received,
“NOT REG.” will be displayed.
About the INPUT mode
"On-screen Display of INPUT Mode (Example)
Using RGB
Using Component
COMPUTER/
COMPONENT 1, 2
mode
COMPONENT 1, 2
mode
VIDEO mode
S-VIDEO mode
COMPUTER 1
RGB
1024 × 768
1
COMPUTER 1
Component
720P/750P
1
VIDEO
V
S-VIDEO
S
Used for projecting images
from equipment that sends
RGB signals or Component
signals connected to the RGB
input terminal.
from equipment that sends
RGB signals or Component
signals connected to the RGB
input terminal.
Used for projecting images
from equipment that sends DVI
Digital RGB and Digital Com-
ponent signals connected to
the DVI-D input terminal.
from equipment that sends DVI
Digital RGB and Digital Com-
ponent signals connected to
the DVI-D input terminal.
Used for projecting images
from equipment connected to
the S-VIDEO input terminal.
from equipment connected to
the S-VIDEO input terminal.
Used for projecting images
from equipment connected to
the VIDEO input terminal.
from equipment connected to
the VIDEO input terminal.
COMPUTER/
COMPONENT
1, 2
COMPONENT
1, 2
DVI-D
S-VIDEO
VIDEO
INPUT buttons
/
/
/
/
DVI-D mode
"On-screen Display of INPUT list
INPUT
1
COMPUTER 1
2
COMPUTER 2
DVI
S-VIDEO
VIDEO
ENTER
SEL.
D
S
V
D. PC RGB
1024
1024
× 768
DVI
D
Click on the first or last page to see other XG-C430X (serv.man2) service manuals if exist.