DOWNLOAD Sharp XG-C40XE (serv.man19) Service Manual ↓ Size: 2.08 MB | Pages: 25 in PDF or view online for FREE

3

2

1, 4

This function can be used to display all the adjusted
settings on the screen simultaneously.

(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)

1 Press MENU.

2 Press ß/© to select “Status”.

3 Press  ENTER  to display all the adjustment

settings.

4 To exit from the GUI, press MENU.

2

3

XG-C40XE/CD (E)-e

01.8.1, 5:58 PM

46

• This projector is equipped with four air filters to ensure

the optimal operating condition of the projector.

• The air filters should be cleaned every 100 hours of

use. Clean the filters more often when the projector is
used in a dusty or smoky location.

• Purchase a replacement air filer (PFILD0076CEZZ)

from your nearest Authorized Sharp LCD Products
Dealer or Service Center when if the filter is torn or
become deteriorated.

Turn over the projector. Press the tab and lift open
the filter cover in the direction of the arrow.

Tab

Air filters
 (not removable)

Air filter

XG-C40XE/CD (E)-f

01.8.1, 5:59 PM

47

Insert the tab on the end of the filter cover into the
filter cover opening and press the filter cover into
position.

Clean the dust off the air filter and cover with a
vacuum cleaner extension hose.

Tab

Grasp the air filter between your
fingers and lift it out of the filter
cover.

Turn over the projector. Press the
tab and lift open the filter cover
in the direction of the arrow.

Insert the tab on the end of the filter cover into the
filter cover opening and press the filter cover into
position.

Tab

• Be sure the filter cover is securely installed. The power will not turn on unless it is correctly installed.

If dust or dirt has collected inside the air filter housing, clean the area with a vacuum cleaner extension hose.

Place the new air filter underneath the tabs on
the filter frame.

Tab

XG-C40XE/CD (E)-f

01.8.1, 5:59 PM

48

TEMPERATURE
WARNING
indicator

LAMP
REPLACEMENT
indicator

POWER
indicator

• The warning lights on the projector indicate problems

inside the projector.

• There are two warning lights: a TEMPERATURE

WARNING indicator which warns that the projector is
too hot, and a LAMP REPLACEMENT indicator which
lets you know when to change the lamp.

• If a problem occurs, either the TEMPERATURE

WARNING indicator or the LAMP REPLACEMENT
indicator will illuminate red. After turning off the power,
follow the procedures given below.

• Lamp has been used for over 1,900

hours.

• Lamp has been used for over 2,000

hours.

• Purchase a replacement lamp unit

(lamp cage/module) of the current
type BQC-XGC40XU/1 from your
nearest Sharp Authorised LCD
Projector Dealer or Service Centre.

• Replace the lamp. (See pages 50

and 51.) If you wish, you may have
the lamp replaced at your nearest
Sharp Authorised LCD Projector
Dealer or Service Centre.

The LAMP REPLACEMENT
indicator illuminates red, and
“LAMP” and “ ” will flash in yellow
in the lower-left corner of the
picture.

The power will automatically turn
off and the projector will enter
standby mode.

“LAMP” and “ ” will flash in red in
the lower-left corner of the picture,
and the power will turn off.

• Blocked air intake.

• Clogged air filter.

• Cooling fan breakdown.
• Internal circuit failure.

• Burnt-out lamp.
• Lamp circuit failure.

• Lamp has been used for

over 1,900 hours.

• The bottom filter cover is

open.

The internal
temperature is
abnormally high.

TEMPERATURE
WARNING indicator

LAMP REPLACE-
MENT indicator

POWER indicator

The lamp does not
illuminate.

The lamp requires
replacement.

The POWER
indicator flashes in
red when the
projector is on.

• Relocate the projector to an area with

proper ventilation.

• Clean the filter.

(See page 47.)

• Take the projector to your nearest Sharp

Authorised LCD Projector Dealer or Service
Centre for repair.

• Carefully replace the lamp. (See pages 50

and 51.)

• Take the projector to your nearest Sharp

Authorised LCD Projector Dealer or Service
Centre for repair.

• Securely install the bottom filter cover.

• If the TEMPERATURE WARNING indicator illuminates, follow the above possible solutions and then wait until the projector has cooled down

completely before turning the power back on. (At least 5 minutes.)

• If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicator may be triggered, preventing

the power from going on. Should this occur, take the power cord out of the wall outlet and put it back in again.

The lamp in this projector operates for approximately 2,000 cumulative hours, depending on the usage environ-
ment. It is recommended that the lamp be replaced after 1,900 cumulative hours of use or when you notice a
significant deterioration of the picture and colour quality. The lamp usage time can be checked with the On-screen
Display (see page 43).

• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.

• As the usage environment can vary significantly, the projector lamp may not operate for 2,000 hours.

XG-C40XE/CD (E)-f

01.8.1, 5:59 PM

49