Sharp MX-RBX1 (serv.man2) Service Manual ▷ View online
MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 6
5)
Disconnect the three connectors [7].
6)
Release the two claws [8] of the harness retainer, and detach
the motor harness [9].
the motor harness [9].
7)
Remove the stop ring [10], and detach the timing belt [11].
8)
Disconnect the connector [12], and free the harness [14] from
the edge saddle [13].
the edge saddle [13].
9)
Remove the two screws [15], and slide the processing tray
assembly [16] to the rear; then lift it to detach.
assembly [16] to the rear; then lift it to detach.
(6) Paddle Assembly
1)
Remove the processing tray assembly. (See B.(3).)
2)
Place the processing tray assembly [1] as shown.
NOTE: Be sure to take care not to damage the aligning plate
[2].
NOTE: Be sure to take care not to damage the aligning plate
[2].
3)
Detach the timing belt [3], and remove the two screws [4].
4)
Separate the processing tray assembly [5] and the paddle
assembly [6] as shown.
assembly [6] as shown.
[9]
[8]
[7]
[11]
[10]
[13]
[14]
[12]
[16]
[15]
[2]
[1]
[3]
[4]
[4]
[6]
[5]
MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 7
(7) Staple/Fold Drive Unit
1)
Open the front door, and slide out the stapler unit slightly to the
front.
front.
2)
Remove the screw [3], and detach the interface retainer [4].
3)
Free the six harness retainers [5], and disconnect the connec-
tor [6].
tor [6].
4)
Free the harness [7] from the harness retainer [5].
5)
Free the harness [7] from the edge saddle [8]; then, disconnect
the two connectors [9].
the two connectors [9].
6)
Release the harness retainer [10], and disconnect the connec-
tor [11].
tor [11].
7)
Free the harness [12] from the harness retainer [10].
8)
Free the harness [12] for the edge saddle [13]; and disconnect
the two connectors [14].
the two connectors [14].
9)
Remove the screw [15], and free the claw [17] of the harness
guide from the long angle [16] of the base plate.
guide from the long angle [16] of the base plate.
10) Disconnect the two connectors [18], and free the harness [20]
from the edge saddle [19].
11) Remove the three screws [21].
12) Remove the screw [22], and detach the staple/fold drive unit
[23].
(8) Feed Motor Unit
1)
Remove the rear cover. (See A.(3).)
2)
Open the harness retainer [1], and disconnect the two connec-
tors [2].
tors [2].
3)
Remove the screw [3], and detach the harness guide [4].
4)
Remove the three screws [5], and detach the feed motor unit
[6].
[6].
1
2
[6]
[7]
[3]
[7]
[8]
[9]
[7]
[5]
[5]
[4] [5] [7] [5]
[12]
[11]
[10]
[13]
[14]
[17]
[15]
[16]
[18]
[18]
[19]
[20]
[21]
[21]
[21]
[22]
[23]
[5]
[5]
[3]
[4]
[6]
[1]
[2]
MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 8
(9) Feed Roller
1)
Remove the upper cover. (See A.(4).)
2)
Remove the upper right cover assembly. (See A.(6).)
3)
Remove the feed motor unit. (See B.(6).)
4)
Remove the screw [1].
5)
Remove the stop ring [2], and detach the bushing [3].
6)
Remove the two screws [4].
7)
Remove the gear [5], and detach the gear [6] while spreading
the claw.
the claw.
8)
Remove the stop ring [7], and detach the bushing [8].
9)
Remove the screw [9], and detach the inlet sensor [10].
10) Remove the lower paper guide [11].
11) Remove the feed roller [12].
(10) Stack Delivery Roller (Upper)
1)
Remove the paddle assembly. (See B.(4).)
2)
Place the paddle assembly [1] as shown.
3)
Turn the gear [2] in the direction of the arrow to move up the
stack delivery roller assembly (upper) [3].
stack delivery roller assembly (upper) [3].
4)
Push up the stack delivery roller (upper) [4] from below to free
the stack deliver roller (upper) [4] from the shaft [5].
the stack deliver roller (upper) [4] from the shaft [5].
[2]
[1] [3]
[4]
[11]
[9]
[10]
[7]
[6]
[8]
[5]
[12]
[1]
[3]
[2]
[4]
[5]
MX-FNX2/AR-PN1/MX-RBX1 DISASSEMBLY AND ASSEMBLY 6 – 9
5)
Shift up the stack delivery roller (upper) [4], and then push it
down to detach the stack deliver roller (upper) [4].
down to detach the stack deliver roller (upper) [4].
6)
Likewise, remove the stack delivery roller (upper) [6] at the
front.
front.
(11) Paddle
1)
Remove the paddle assembly. (See B.(4).)
2)
Place the paddle assembly [1] as shown.
3)
Turn the gear [2] in the direction of the arrow to move up the
stack delivery roller assembly (upper) [3].
stack delivery roller assembly (upper) [3].
4)
Push up the safety guide [4] from below to free one side of the
safety guide [4] from the shaft [5].
safety guide [4] from the shaft [5].
5)
Push up the safety guide [4] from below to free the safety
guide [4] from the shaft [5].
guide [4] from the shaft [5].
6)
Remove the paddle [6] in the direction of the arrow.
7)
Likewise, remove the other paddle.
(12) Stack Delivery Roller (Lower)/Delivery Belt
1)
Remove paddle assembly, and separate it from the processing
tray assembly. (See B.(4).)
tray assembly. (See B.(4).)
2)
Slide the aligning plate (front) [2] and the aligning plate (rear)
[3] of the processing tray assembly [1] by sliding them to the
outside.
[3] of the processing tray assembly [1] by sliding them to the
outside.
3)
Remove the processing tray stopper [4].
4)
Remove the screw [5], and detach the paper guide (front) [7]
while freeing the two claws [6].
while freeing the two claws [6].
[4]
[6]
[1]
[3]
[2]
[4]
[5]
[4]
[5]
[6]
[1]
[3]
[2]
[4]
[5]
[7]
[6]
Click on the first or last page to see other MX-RBX1 (serv.man2) service manuals if exist.