Sharp MX-M950 / MX-MM1100 (serv.man38) Service Manual ▷ View online
MX-M1100 SIMULATION 7 – 29
Note:1 When the above operation is interrupted in the middle, the
reference toner density control level is not set.
Note:2 If the reference toner density control level is not set nor-
mally, the error code, EE-EL or EE-EU, is displayed.
<<Result display item name>>
reference toner density control level is not set.
Note:2 If the reference toner density control level is not set nor-
mally, the error code, EE-EL or EE-EU, is displayed.
<<Result display item name>>
<<Result display item name>>
25-6
Purpose
Setting
Function (Purpose) Used to adjust the sensitivity of the devel-
oper adjustment sensor and the toner den-
sity sensor.
(This setting is executed when developer
together with the toner density sensor or
developer together with the developing unit
is replaced.) (Automatic adjustment)
sity sensor.
(This setting is executed when developer
together with the toner density sensor or
developer together with the developing unit
is replaced.) (Automatic adjustment)
Section
Process (Developing section)
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
After stopping the developing motor, the reference toner den-
sity control level and the toner density sensitivity adjustment
value are set.
sity control level and the toner density sensitivity adjustment
value are set.
(Note1)
If the above operation is interrupted in mid-course, the reference
toner density control level and the toner density sensitivity adjust-
ment value are not set.
(Note2)
If the error code EE-EL or EE-EF is displayed, it means the refer-
ence toner density control level and the toner density sensitivity
adjustment value are not set properly.
If the above operation is interrupted in mid-course, the reference
toner density control level and the toner density sensitivity adjust-
ment value are not set.
(Note2)
If the error code EE-EL or EE-EF is displayed, it means the refer-
ence toner density control level and the toner density sensitivity
adjustment value are not set properly.
<<Result display item name>>
26
26-2
Purpose
Setting
Function (Purpose) Used to set the paper size of the tandem
tray/large capacity paper feed tray (LCC).
(When the paper size is changed, this sim-
ulation must be used to change the paper
size on the software.)
(When the paper size is changed, this sim-
ulation must be used to change the paper
size on the software.)
Section
Paper feed
Operation/Procedure
Select a paper size to be changed with the touch panel.
Select a paper size to be changed with the touch panel.
26-3
Purpose
Setting
Function (Purpose) Used to set the auditor specification mode.
(Setting must be made according to the use
conditions of the auditor.)
conditions of the auditor.)
Section
Auditor
Operation/Procedure
Select a target of setting with the touch panel.
Select a target of setting with the touch panel.
Display Item name
Description of item content
Display
range
De-
fault
value
HUMIDITY AREA
Humidity area registered value
0 - 15
DEVE REFERENCE
Automatic developer
adjustment value
adjustment value
0 - 255
CONTROL
VOLTAGE
VOLTAGE
Execution control voltage
registered value
registered value
0 - 255
Sensor name
(display)
Sensor name (Display)
HUMIDITY AREA
Humidity area
DEVE REFERENCE
ATC sensor value
CONTROL
VOLTAGE
VOLTAGE
Control voltage
Category
Display Item
name
Description of item
content
Display
range
De-
fault
value
TONER
SENSOR
MONITOR
SENSOR
MONITOR
HUMIDITY
AREA
AREA
Humidity area
0 - 15
DEVE
REFERENCE
REFERENCE
ATC sensor value
0 - 255
CONTROL
VOLTAGE
VOLTAGE
Control voltage
0 - 255
AUTO DEVE
ADJUSTMENT
ADJUSTMENT
HUMIDITY
AREA
AREA
Humidity area
registered value
registered value
0 - 15
DEVE
REFERENCE
REFERENCE
Automatic developer
adjustment value
adjustment value
0 - 255
CONTROL
VOLTAGE
VOLTAGE
Execution control
voltage registered
value
voltage registered
value
0 - 255
STANDARD
DENSITY
ADJUSTMENT
DENSITY
ADJUSTMENT
STD
HUMIDITY
AREA
HUMIDITY
AREA
Reference humidity
area
area
0 - 15
STANDARD
VREF
VREF
Reference transit
target registered
value
target registered
value
0 - 255
STANDARD
DENSITY
ADJUSTMENT
DENSITY
ADJUSTMENT
STANDARD
VCON
VCON
Reference control
voltage registered
value
voltage registered
value
0 - 255
AUTO ATC
DENSITY
ADJUST
SETUP
DENSITY
ADJUST
SETUP
HUMIDITY
AREA
AREA
Humidity area
registered value
registered value
0 - 15
VREF SENS
(ATC)
(ATC)
Coefficient
registered value
corrected for ATC
reference gain
registered value
corrected for ATC
reference gain
80 - 120
VCON SENS
(ATC)
(ATC)
Coefficient
registered value
corrected for ATC
reference control
voltage
registered value
corrected for ATC
reference control
voltage
80 - 120
Item
Setting value
Content
TRAY1
0
8.5
✕ 11
1
A4
2
B5
A4 LCC
0
8.5
✕ 11
1
A4
2
B5
A4 3LCT
0
8.5
✕ 11
1
A4
2
B5
3
5.5
✕ 8.5R
4
A4W
5
A5R
BUILT-IN
AUDITOR
AUDITOR
P10 *
Built-in auditor mode (standard mode)
operation (Default)
operation (Default)
EC1
EC1 mode operation
OUTSIDE
AUDITOR
AUDITOR
NONE *
Normal operation (Default)
P VENDOR1
Old coin vendor mode (Copy mode
control)
control)
P OTHER
Vendor mode for the external auditor
connected to the coin vendor I/F
connected to the coin vendor I/F
S_VENDOR
Serial vendor
DOC ADJ
ON
Document filing function available
OFF *
Document filing function not available
(Default)
(Default)
PF ADJ
ON
Continuous feeding is performed.
OFF *
Continuous feeding is not performed.
(Default)
(Default)
Category
Display Item
name
Description of item
content
Display
range
De-
fault
value
MX-M1100 SIMULATION 7 – 30
(*) VENDOR MODE detail
Operation 1: Standby during auto clear setting time.
Default: 60 sec. Can be varied by the system setting.
Operation 2 : Auto clear is not performed.
Operation 3 : Shifts to the initial screen.
Operation 3 : Shifts to the initial screen.
26-5
Purpose
Setting
Function (Purpose) Used to set the count mode of the total
counter and the maintenance counter.
(A3/11 x 17 size)
(A3/11 x 17 size)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
1=1 count-up, 2=2 count-up
1=1 count-up, 2=2 count-up
2)
Press [OK] key.
26-6
Purpose
Setting
Function (Purpose) Used to set the specifications of each desti-
nation (paper, fixed magnification ratio,
etc.)
etc.)
Section
Operation/Procedure
1)
1)
Select a target of setting with the touch panel.
2)
Press [EXECUTE] key.
The selected set item is saved.
The selected set item is saved.
26-10
Purpose
Setting
Function (Purpose) Used to set the trial mode of the network
scanner.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value of step 1 is saved.
The set value of step 1 is saved.
26-18
Purpose
Setting
Function (Purpose) Used to set YES/NO of the toner save
mode operation. (For Japan and UK ver-
sions.)
sions.)
Section
Operation/Procedure
1)
1)
Select a target item of setting with [
↑] [↓] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value of step 2 is saved.
The set value of step 2 is saved.
26-30
Purpose
Setting
Function (Purpose) Used to set the CE mark support (Europe
safety standards) operation mode. (Sup-
porting slow start of the fusing heater lamp
when driving it)
porting slow start of the fusing heater lamp
when driving it)
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
0: Control enable
0: Control enable
1: Control disable
2)
Press [OK] key.
The set value of step 1 is saved.
The set value of step 1 is saved.
<<Default/ Setting value by destination>>
Vendor mode
(*)
(*)
MODE1
Vendor mode 1
MODE2
Vendor mode 2
MODE3 *
Vendor mode 3 (Default)
COUNTUP
TIMING
TIMING
FUSER_IN
When paper lead edge passes the
fusing rear sensor.
fusing rear sensor.
FUSER_OUT
When paper rear edge passes the fusing
rear sensor.
rear sensor.
EXIT_OUT *
When paper rear edge passes the paper
exit sensor in the main unit, the right
tray, and the after-process unit. (Default)
exit sensor in the main unit, the right
tray, and the after-process unit. (Default)
*: Default value
Completion
of the
specified
quantity
(with money
left)
Insufficient fee during a
copy job
Completion
of the
specified
quantity
(with money
left)
B/W
⋅ Color
(With no
money left)
Color
(with money
left)
Condition 1
Condition 2
Condition 3
Condition 4
MODE1
Operation 1
Operation 2
Operation 2
Operation 1
MODE2
Operation 1
Operation 1
Operation 2
Operation 1
MODE3
Operation 1
Operation 3
Operation 2
Operation 3
Item
Display
Content
Set
ting
range
De-
fault
value
A
TOTAL (B/W)
Total counter (B/W)
1 - 2
2
B
MAINTE (B/W)
Maintenance counter (B/W)
1 - 2
2
C
DEV (B/W)
Developer counter (B/W)
1 - 2
2
U. S. A.
United States of America
CANADA
Canada
INCH
Inch series, other destinations
JAPAN
Japan
AB_B
AB series (B5 detection), other destinations
EUROPE
Europe
U. K.
United Kingdom
AUS.
Australia
AB_A
AB series (A5 detection), other destinations
CHINA
China
TRIAL MODE
(0: YES 1: NO)
(0: YES 1: NO)
0 : Trial mode setting
1 : Trial mode cancel (Default)
1 : Trial mode cancel (Default)
A
COPY
0 : Copy toner save mode disable (Default)
1 : Copy toner save mode Enable
1 : Copy toner save mode Enable
B
PRINTER
0 : Printer toner save mode disable (Default)
1 : Printer toner save mode Enable
1 : Printer toner save mode Enable
Display
Content
Setting
range
Default value
(0 : YES
1 : NO)
1 : NO)
0 : CE mark control Enable
0 - 1
<<Default/ Setting
value by destination>>
1 : CE mark control disable
Destination
Setting value
U.S.A.
1 (CE support not available)
CANADA
1 (CE support not available)
INCH
1 (CE support not available)
JAPAN
1 (CE support not available)
AB_B
1 (CE support not available)
EUROPE
0 (CE support available)
U.K.
0 (CE support available)
AUS.
0 (CE support available)
AB_A
0 (CE support available)
CHINA
0 (CE support available)
MX-M1100 SIMULATION 7 – 31
26-35
Purpose
Setting
Function (Purpose) Used to set the display type of troubles in
Sim. 22-4. When two or more same trou-
bles occur continuously, the trouble history
is displayed as one trouble or as two or
more troubles occurring continuously.
bles occur continuously, the trouble history
is displayed as one trouble or as two or
more troubles occurring continuously.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value of step 1 is saved.
The set value of step 1 is saved.
26-38
Purpose
Setting
Function (Purpose) Used to set whether printing is terminated
or not when the developer life is reached or
when the fuser web end.
when the fuser web end.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value of step 1 is saved.
The set value of step 1 is saved.
26-41
Purpose
Setting
Function (Purpose) Used to set YES/NO of the magnification
ratio auto select function (AMS) in the cen-
ter binding mode.
ter binding mode.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
0: AMS cancel 1: AMS setting
0: AMS cancel 1: AMS setting
2)
Press [OK] key.
The set value of step 1 is saved.
The set value of step 1 is saved.
26-49
Purpose
Setting
Function (Purpose) Used to set the postcard copy speed mode.
Section
Section
Operation/Procedure
Select a copy speed mode with the touch panel. (Default: LOW)
Select a copy speed mode with the touch panel. (Default: LOW)
26-50
Purpose
Setting
Function (Purpose) Used to set Enable/Disable of black/white
reverse function.
Section
Operation/Procedure
1)
1)
Select a target item of setting with [
↑] [↓] keys on the touch
panel.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
<<Default setting by destinations>>
Display
Content
Default
value
(0 : ONCE
1 : ANY)
1 : ANY)
0 : Only once. If the trouble is the same as the
previous one, it is not saved.
previous one, it is not saved.
0
1 : Any time. Though the trouble is the same as
the previous one, it is saved.
the previous one, it is saved.
Display
Content
Set-
ting
ting
range
De-
fault
value
A
MAINTENANCE
LIFE OVER
(0 : CONTINUE
1 : STOP)
LIFE OVER
(0 : CONTINUE
1 : STOP)
0
Print enable setting (print
continue) when
maintenance life is over
continue) when
maintenance life is over
0 - 1
0
1
Print disable setting (print
stop) when maintenance
life is over
stop) when maintenance
life is over
U. S. A
0 (Cancel)
EUROPE
1 (Setting)
CANADA
0 (Cancel)
U. K.
1 (Setting)
INCH
0 (Cancel)
AUS.
0 (Cancel)
JAPAN
0 (Cancel)
AB_A
0 (Cancel)
AB_B
0 (Cancel)
CHINA
0 (Cancel)
Item
Setting
value
Content
Default
value
POST CARD
LOW
Postcard copy speed LOW
LOW
HIGH
Postcard copy speed HIGH
Item
Display
Content
Setting
range
Default
value
A
BW RE-
VERSE
VERSE
YES
B/W reverse allowed
0 - 1
1 Refer to
<<Default
setting by
destina-
tions>>
setting by
destina-
tions>>
NO
B/W reverse inhibited
0
B
JOB
STATUS
LED
STATUS
LED
MODE
1
1
Job
status
LED
lighting
status is
selected.
status
LED
lighting
status is
selected.
MODE1
(Red LED
ON/blink/
OFF)
(Red LED
ON/blink/
OFF)
0 - 1
0
0
MODE
2
2
MODE2
(Red LED
always
OFF)
(Red LED
always
OFF)
1
C
GBC
PUNCH
SET
PUNCH
SET
INCH
Used to
select
AB
series or
inch
series of
GBC
punch
unit
select
AB
series or
inch
series of
GBC
punch
unit
Inch
series
series
0 - 1
0 Refer to
<<Default
setting by
destina-
tions>>
setting by
destina-
tions>>
AB
AB series
1
Destination
Default value
(Item A)
Default value
(Item C)
U.S.A.
1 (Display Enable)
0 (Inch series)
CANADA
1 (Display Enable)
0 (Inch series)
INCH
1 (Display Enable)
0 (Inch series)
JAPAN
1 (Display Enable)
1 (AB series)
AB_B
1 (Display Enable)
1 (AB series)
EUROPE
1 (Display Enable)
1 (AB series)
U.K.
0 (Display Disable)
1 (AB series)
AUS.
1 (Display Enable)
1 (AB series)
AB_A
1 (Display Enable)
1 (AB series)
CHINA
1 (Display Enable)
1 (AB series)
MX-M1100 SIMULATION 7 – 32
26-52
Purpose
Setting
Function (Purpose) Used to set whether non-print paper (inser-
tion, cover sheet) is counted or not.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
0: Counted up. 1: Not counted.
0: Counted up. 1: Not counted.
2)
Press [OK] key.
The set value of step 1 is saved.
The set value of step 1 is saved.
26-69
Purpose
Setting
Function (Purpose) Used to set preliminary preparation of toner
and near end display when the toner quan-
tity reaches 25%.
tity reaches 25%.
Section
Operation/Procedure
1)
1)
Select a target item of setting with [
↑] [↓] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value of step 2 is saved.
The set value of step 2 is saved.
(*): Setting of 1 and 2 is enabled for Japan only.
<<Setting item (TONER END) control content>>
<<Setting item (TONER END) control content>>
27
27-1
Purpose
Setting
Function (Purpose) Used to set non-detection of the communi-
cation error (U7-00) with RIC.
Section
Operation/Procedure
1)
1)
Enter the set value with 10-key.
0: Non-detection 1: Detection
0: Non-detection 1: Detection
2)
Press [OK] key.
The set value of step 1 is saved.
The set value of step 1 is saved.
27-2
Purpose
Setting
Function (Purpose) Used to set the FSS function (user registra-
tion number, Host server telephone num-
ber).
ber).
Section
Operation/Procedure
1)
1)
Select a target of setting with the touch panel.
[USER FAX NO][SERVA TEL NO]
[USER FAX NO][SERVA TEL NO]
2)
Enter the set value with 10-key.
3)
Press [SET] key.
The set value of step 2 is saved.
The set value of step 2 is saved.
27-4
Purpose
Setting
Function (Purpose) Used to set the FSS function (initializing,
call, toner order auto send).
Section
Operation/Procedure
1)
1)
Select a target item of setting with [
↑] [↓] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value of step 2 is saved.
The set value of step 2 is saved.
(0 : ONCE 1 : ANY)
0 : White paper is counted up.
1 : White paper is not counted.
1 : White paper is not counted.
Item
Display
Content
Setting range
Default
value
A
TONER
PREPARATION
(0: YES
1: NO)
PREPARATION
(0: YES
1: NO)
0: Toner ready
message and the
icon are displayed.
message and the
icon are displayed.
0 - 1
0
1: Toner ready
message and the
icon are not
displayed.
message and the
icon are not
displayed.
B
TONER NEAR
END
(0: YES
1: NO)
END
(0: YES
1: NO)
0: Toner near end
message is
displayed.
message is
displayed.
0 - 1
0
1: Toner near end
message is not
displayed.
message is not
displayed.
C
TONER END
1: When toner end,
cartridge motor
operation Enable
cartridge motor
operation Enable
1 - 3
(Setting invalid
except for
Sim26-6
Overseas.)
3
(*)
2: When toner end,
cartridge motor
operation Disable
3: When toner end,
cartridge motor
operation Disable
cartridge motor
operation Disable
3: When toner end,
cartridge motor
operation Disable
D
TONER END
JUDGMENT
JUDGMENT
1: TH counter 1
(Toner hopper motor
1 accumulated
rotating time)
(Toner hopper motor
1 accumulated
rotating time)
1 - 2
1
2: Judgment of
toner end by ATC
(Exhausted in the
intermediate
hopper)
toner end by ATC
(Exhausted in the
intermediate
hopper)
Toner end flag
detection
CRUM ID machine
history check
(*1)
No detection
No detection
(*2)
No detection
Detection
(*3)
Detection Detection
USER FAX_NO.
User registration number (Max. 16 digits)
SERVA TEL_NO.
Host server TEL number (Max. 16 digits)
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man38) service manuals if exist.