Sharp MX-M905 Handy Guide ▷ View online
SHARP
CONSUMABLES
13
FUSING UNIT:
MX-M905
Product Code
Description / Contents
Approx. Life
MX-950HK
Fusing Roller Kit:-
Upper heat roller unit
Lower heat roller unit
Lower heat roller unit
1000k
MX-950KC
Fuser Maintenance Kit:-
Fusing separation pawl (upper) x6
Fusing separation pawl (lower) x4
Fusing front paper guide (upper)
Fusing separation pawl (lower) x4
Fusing front paper guide (upper)
500k
MX-950WC
Web Cleaning Kit:-
Web roller.
Web backup roller
Web backup roller bearing x2
Web guide shaft
Web guide shaft bearing x2
Web backup roller
Web backup roller bearing x2
Web guide shaft
Web guide shaft bearing x2
500k
PERIPHERALS
MX-SCX1
Saddle Staple Cartridge (for MXFN22)
5000 staples (x 3)
MX-SCX2
Staple Cartridge (for MXFN21/MXFN22)
5000 staples (x 3)
MX-SCX3
Saddle Staple Cartridge (For MXFN25)
2000 staples (x 4)
AR-SC2
Staple Cartridge (for MX-FN24/25)
5000 staples (x 3)
AR-SV1
Stamp Cartridge (for AR-SU1)
2 cartridges
SERVICE ROTATION:
MX-900TU
Transfer Belt Unit
For Service Rotation
MX-900FU
Fusing Unit (230v)
MX-900WU
Web Cleaning Unit
Note:
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.
INITIAL SETUP
SHARP
14
UNPACKING & LOCK REMOVAL:
Use Skid Slopes [UKOG-0367FCZZ] to remove device from shipping pallet.
Operation Panel installation.
Remove Tray Lift Lock Plates.
Release Fusing Pressure.
DEVELOPER SETUP:
Sim 25-02 Auto Developer Adjustment - Select K.
Toner Installation must be performed after Auto Developer Adjustment is
completed.
For optimum image quality and performance, it is recommended to setup
and install Developer at the customer site (environment).
TONER INSTALLATION & REPLENISHMENT:
Install Toner Cartridge [K]:
Caution:
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation
Mode during Initial Toner Replenishment.
PRODUCT ACTIVATION & FIRMWARE UPGRADE:
Activation of Optional Products:
System Settings – Product Key.
Sim 22-05 Check Firmware Version(s):
Upgrade to latest version.
INITIAL SETUP:
Sim 21-01
Maintenance Cycle Setting:
Set PM Counter = 500k,
Sim 26-02
LCC Installation (Paper Size):
A4/Letter.
Sim 26-06
Machine Destination check.
Sim 26-35
Set Multi Error Counter:
Set to 1 (Multi Count).
Sim 26-52
Non Printed Paper Counter Set-up.
Sim 40-12
Multi Purpose Tray (Tray 4) Adjustment/Calibration.
Sim 55-03
Process Mixed Size Pages (orientation) when Printing in Duplex:
SSW 3-6, 0 = Disable, 1 = Enable.
Adjust Date/Time (Inc. Daylight Saving setting):
System Settings – Clock Adjust.
Keyboard Language Setting:
System Settings – Default Settings – Keyboard Select: Set English(US).
Paper Size & Type Settings:
System Settings – Paper Tray Settings.
Set cassette size by adjusting the guides in the cassette.
SHARP
INITIAL SETUP
15
PRINT ENGINE IMAGE SKEW:
Sim 64-02
Image Writing Adjustment:-
Select A=1, B=1, C=254, D=255, E=1, F=1, G=8.
PRINT IMAGE POSITION & BK MAGNIFICATION:
Check Print Image Off Centre & Lead Edge position - Use Sim 50-10:-
Inside dimension of the printed halftone must be 240±0.5mm.
Lead edge void area 3.0 ± 1.0mm.
Rear edge void area 2.0mm - 5.0mm.
Front & Rear Void areas 2.0 ± 2.0mm.
Lead edge void area 3.0 ± 1.0mm.
Rear edge void area 2.0mm - 5.0mm.
Front & Rear Void areas 2.0 ± 2.0mm.
If NG, perform the following adjustments as required:-
Manual Adjustment:
Sim 50-10
BK MAG / Image Off Centre Adjustment (All Trays).
Sim 50-05
Printer Lead Edge & Void Adjust.
Automatic Adjustment:
Sim 50-28
BK MAG ADJ (Main Scan Mag).
SETUP/PRINT ADJ (Lead, Offset or All).
ENGINE & PRINTER HALF TONE ADJUSTMENT:
Sim 46-74
Engine & Printer Half Tone Calibration:
Select FACTORY Mode.
IMAGE QUALITY CHECK [COPY & PRINT]
Check Image Quality (Copy Mode) – Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:-
Sim 46-02
Copy Density Adjust. (B/W).
Sim 46-09
SPF Copy Density Adjust.
Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc):
Sim 48-01
Magnification Adjustment (OC & SPF).
Sim 50-01
Lead/Rear Edge, Loss & Void Adjust.
Sim 50-12
OC & SPF Off Centre Adjust.
Check SPF Skew adjustment.
Automatic Adjustment:
Sim 50-28
OC ADJUST (Lead, Offset & Mag).
SPF ADJ:(Lead, Offset & Sub scan).
Check Print Image Quality:
Sim 64-05
PCL Density Test Page.
Sim 64-06
PS Density Test Page.
INITIAL SETUP
SHARP
16
PERIPHERAL / OPTION CONFIGURATION
MULTI BYPASS TRAY – MX-MFX1:
Sim 40-02
Bypass Tray Adjustment [MX-MFX1 only].
FACSIMILE OPTION – MX-FX15:
Sim 66-02
Fax SW Setting (Destination).
Sim 66-10
Image Data Memory Clear.
Sim 66-39
Fax Destination Set
FINISHER OPTION – MX-FN21/22/24/25:
Sim 03-10
Saddle Fold/Staple Position Adjustment [MX-FN22/25 only].
Sim 26-65
Finisher Alarm Mode:-
Limit number of Copies in staple mode (ON/OFF).
Limit the number of sets loaded in the saddle staple (ON/OFF).
**Limit load of folded paper on paper exit and limit load on 50-sheet
Staple saddle finisher are set in SADDLE COPIES.
FOLDING UNIT – MX-FD10:
Z Fold Skew Adjustment check
EXTERNAL ACCOUNTING MODULE – MX-AMX3:
Sim 55-03
Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03
Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06
Data Simulation Print
Device Clone & Storage Backup
Sim 56-01
Backup EEPROM Data to HDD
Click on the first or last page to see other MX-M905 service manuals if exist.