DOWNLOAD Sharp MX-M904 / MX-M1204 (serv.man9) Service Manual ↓ Size: 27.84 MB | Pages: 127 in PDF or view online for FREE

MX-M1204  MX-MFX1 (MULTI BYPASS TRAY)  4 – 4

2)

Open the manual paper feed guide to the maximum width, and
press [EXECUTE] key.

[EXECUTE] key is highlighted. When the maximum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

3)

Set the manual paper feed guide to the A4 width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the A4 size width detec-
tion level adjustment value is saved, [EXECUTE] key returns
to the normal display.

4)

Set the manual paper feed guide to the A4R width, and press
[EXECUTE] key.

[EXECUTE] key is highlighted. When the A4R size width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display

5)

Set the manual paper feed guide to the minimum width, and
press [EXECUTE] key.

[EXECUTE] key is highlighted. When the minimum width
detection level adjustment value is saved, [EXECUTE] key
returns to the normal display.

When the adjustment is finished, Complete is displayed.

MAX POSITION

Maximum width detection level adjustment

P1 (A4) POSITION

A4 width detection level adjustment

P2 (A4R) POSITION

A4R width detection level adjustment

MIN POSITION

Minimum width detection level adjustment

MX-M1204  MX-LC12 (LARGE CAPACITY TRAY)  5 – 1

MX-M1204

Service Manual

 

Since the illustrations of the former models are used, they may differ from the actual cases.

NOTE: When the MX-LC12 is installed, first install the MX-MFX1.

(The paper transport guide for the MX-LC12/MX-LC13 packed together with the MX-MFX1 is required. For the details, refer to the installation
manual of the MX-MFX1.)

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

NOTE: When installing the MX-LC12, lower the adjusters of the

machine to the floor.

1)

Remove the paper feed desk fixing screw.

NOTE: Before turning on the power, check to insure that the fixing

screw of the tray is removed. If the power is turned on with-
out removing the fixing screw, a trouble may be resulted.

1)

Attach the mounting plate upper (Packed items) with the fixing
screw A (Packed items) to the installation part of right side of
the main unit. When installing, put the rubber section (

) of

the mounting plate upper on the lower side.

2)

Remove the fixing screws of the front/rear cover on the lower
part of the main unit. Attach the connecting plate lower front
(Packed items) to the lower front side of the main unit with the
fixing screw B (Packed items).
Attach the connecting plate lower rear (Packed items) to the
lower rear side of the main unit with the fixing screw B (Packed
items).

NOTE: Remove the front and rear covers, then remove the

screws (in the rear side only) as shown in the figure
below. (The removed screws are not used.)

1

Mounting plate upper

2

2

Connecting plate lower front

1

3

Connecting plate lower rear

1

4

Fixing screw A (Hex washer S-tight M4x18)

4

5

Fixing screw B (Hex washer S-tight M4x12)

4

2

1

3

4

5

MX-M1204  MX-LC12 (LARGE CAPACITY TRAY)  5 – 2

3)

Remove the fixing screws (2 pcs.) of the machine entry port,
and remove the entry port cover.

4)

Reverse the entry port cover and re-attach it to the machine.
Secure it with the two previously removed screws in procedure
3).

NOTE: Be careful not to make a scratch for the paper pass

surface of entrance cover at the installation.

1)

Hold the grips of the front and the rear cabinets with both
hands, and lift the left side.

2)

Hang the metal fixture of the large capacity tray on the lower
front/rear connecting plate of the main unit side. Push the large
capacity tray onto the main unit and attach it.

To confirm that the large capacity tray is locked into place pull
it in the direction of the arrow as shown.

NOTE: If lock is incomplete, when the power switch is turned

on, the message, “Check installation of tray 5” is dis-
played on the operation panel.

NOTE: Push the large capacity tray onto the machine, and

lock it securely.

NOTE: When lifting the LCC, insert fingers firmly into the grip sec-

tions of the front and rear cabinets and install slowly.

NOTE: Turn the lock release screw of the front cover counterclock-

wise to loosen and check that the screw is free.

* If the screw is tight at that time, installation will be incom-

plete.

F

R

MX-M1204  MX-LC12 (LARGE CAPACITY TRAY)  5 – 3

1)

Turn the lock release screw of the front cover clockwise and
tighten the screw securely to release lock.

2)

Then hold the grips of the front and the rear cabinets with both
hands, and lift the left side. The large capacity tray will come
off.

1)

After installing the large capacity tray to the main unit, loosen
the screws (one in the front and one in the rear) of the adjust-
ment caster mounting plate attached to the lower side of the
large capacity tray.
At that time, the casters of the adjustment caster mounting
plate are brought into contact with the floor by the spring force.

2)

Tighten the screws (one in the front and one in the rear) of the
caster mounting plate which were loosened in procedure 1).

1)

Remove the fixing screw from the connector cover on the main
unit and then remove the connector cover.

F side

R side