Sharp MX-M904 / MX-M1204 (serv.man2) Handy Guide ▷ View online
SHARP
POWER REQUIREMENTS
13
Power Requirements:
MX-M1055/1205:
MX-M1055/1205:
MX-M904/1054/1204:
MX-M904
**
MXM1055 / MXM1205
Voltage
Europe: 220-240V 10 A + 220-240V 2A
Europe: 220-240V 13A
Frequency
Europe: 50/60 Hz 13A
Power Cord
Direct connection x 1 +
Inlet Type x 1 for options
Direct connection x 1
Power Switch
2 switches: Primary switch: inside the front cover,
Secondary switch (momentary SW): on the operation panel
Important Note
DO NOT use extension cables and/or plug multiple plugs into 1 breaker.
MX-LC13N, MX-ST10 & MX-FN21/22 should be plugged into separate breakers to
the machine. Failure to observe these recommendations could lead to
permanent damage of the device.
**
CONSUMABLES
SHARP
14
CONSUMABLES
Product Code
Description / Contents
Approx. Life
MX-900GT
Black Toner Cartridge
(A4 @ 6%)
120k
PROCESS UNIT:
MX-900GV
Black Developer
1000k
MX-850GR
OPC Drum
1000k
MX-900DK
Developer Maintenance Kit:-
Doctor cover unit/DV Seal
DV side seal F
DV side seal R
DV box filter
DV toner filter
DV side seal F
DV side seal R
DV box filter
DV toner filter
1000k
MX-900CB
Cleaner Blade Kit:-
Cleaning blade
Side seal F
Side seal R
Sub blade
Drum separation pawl x4
Duct sheet
Side seal F
Side seal R
Sub blade
Drum separation pawl x4
Duct sheet
500k
MX-900MK
Main Charge Kit:-
Charger wire x2
Screen grid
Charger cleaner
Charger cushion
Cleaner base guide
Screen grid
Charger cleaner
Charger cushion
Cleaner base guide
500k
MX-850HB
Waste Toner Collector:-
Includes CAP
500k
MX-900FL
Ozone Filter Kit:-
Ozone filter.
Outlet filter
Outlet filter
500k
(or 6 months)
MX-900PD
Paper Dust Removing Kit:-
Paper dust removal unit.
500k
TRANSFER SECTION:
MX-900TT
Transfer Belt Kit:-
Transfer belt
Transfer roller
Transfer cleaning blade
Ball bearing x4
Transfer roller
Transfer cleaning blade
Ball bearing x4
1000k
SHARP
CONSUMABLES
15
FUSING UNIT:
Product Code
Description / Contents
Approx. Life
MX-950HK
Fusing Roller Kit:-
Upper heat roller unit
Lower heat roller unit
Lower heat roller unit
1000k
MX-950KC
Fuser Maintenance Kit:-
Fusing separation pawl (upper) x6
Fusing separation pawl (lower) x4
Fusing front paper guide (upper)
Fusing separation pawl (lower) x4
Fusing front paper guide (upper)
500k
MX-950WC
Web Cleaning Kit:-
Web roller.
Web backup roller
Web backup roller bearing x2
Web guide shaft
Web guide shaft bearing x2
Web backup roller
Web backup roller bearing x2
Web guide shaft
Web guide shaft bearing x2
500k
PERIPHERALS
MX-SCX1
Saddle Staple Cartridge (for MXFN22)
5000 staples (x 3)
MX-SCX2
Staple Cartridge (for MXFN21/MXFN22)
5000 staples (x 3)
MX-SCX3
Saddle Staple Cartridge (For MXFN25)
2000 staples (x 4)
AR-SC2
Staple Cartridge (for MX-FN24/25)
5000 staples (x 3)
AR-SV1
Stamp Cartridge (for AR-SU1)
2 cartridges
SERVICE ROTATION:
MX-900TU
Transfer Belt Unit
For Service Rotation
MX-900FU
Fusing Unit (230v) for MX-M904 only
MX-901FU
Fusing Unit (230v) for MX-M1054/1055/1204/1205
MX-900WU
Web Cleaning Unit
Note:
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.
INITIAL SETUP
SHARP
16
UNPACKING & LOCK REMOVAL:
Use Skid Slopes [UKOG-0367FCZZ] to remove device from shipping pallet.
Operation Panel installation.
Remove Tray Lift Lock Plates.
Release Fusing Pressure.
DEVELOPER SETUP:
Sim 25-02 Auto Developer Adjustment - Select K.
Toner Installation must be performed after Auto Developer Adjustment is
completed.
For optimum image quality and performance, it is recommended to setup
and install Developer at the customer site (environment).
TONER INSTALLATION & REPLENISHMENT:
Install Toner Cartridge [K]:
Caution:
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation
Mode during Initial Toner Replenishment.
PRODUCT ACTIVATION & FIRMWARE UPGRADE:
Activation of Optional Products:
System Settings – Product Key.
Sim 22-05 Check Firmware Version(s):
Upgrade to latest version.
INITIAL SETUP:
Sim 21-01
Maintenance Cycle Setting:
Set PM Counter = 500k,
Sim 26-02
LCC Installation (Paper Size):
A4/Letter.
Sim 26-06
Machine Destination check.
Sim 26-35
Set Multi Error Counter:
Set to 1 (Multi Count).
Sim 26-52
Non Printed Paper Counter Set-up.
Sim 40-12
Multi Purpose Tray (Tray 4) Adjustment/Calibration.
Sim 55-03
Process Mixed Size Pages (orientation) when Printing in Duplex:
SSW 3-6, 0 = Disable, 1 = Enable.
Adjust Date/Time (Inc. Daylight Saving setting):
System Settings – Clock Adjust.
Keyboard Language Setting:
System Settings – Default Settings – Keyboard Select: Set English(US).
Paper Size & Type Settings:
System Settings – Paper Tray Settings.
Set cassette size by adjusting the guides in the cassette.
Click on the first or last page to see other MX-M904 / MX-M1204 (serv.man2) service manuals if exist.