Sharp MX-M700U (serv.man3) Service Manual ▷ View online
AR-M550/M620/M700 INSTALLATION MANUAL (AR-F15/F16) 4 - 6
1) Remove the fixing screw of base cover (2 positions) in the front and
the back of the finisher, and remove the base cover.
2) Remove the fixing screws (2 pcs.) of the rear cover on the rear of
the finisher, and remove the rear cover.
3) Only for the AR-F15, remove the front cabinet lower fixing screws
(2 pcs.).
4) Open the front cabinet lower, and loosen the fixing screws (2 pcs
for each) of four casters.
5) Remove the spanner stored inside of the front cabinet upper, and
close the front cabinet upper.
6) Turn the bolt with the removed spanner so that the guide pin is in
the specified range of the scale.
(At that time, lift the finisher a little, and the bolt can be turned man-
ually.)
ually.)
7) After completion of the adjustment, tighten the caster fixing screws
(8 pcs.) and close the front cabinet lower.
8) Check to insure that the intervals at the upper and the lower sides
of the main unit and the finisher are even.
9) Attach the foot covers in front and at the back of the finisher and the
rear cover on the rear side, and tighten all the fixing screws.
AR-M550/M620/M700 INSTALLATION MANUAL (AR-F15/F16) 4 - 7
(5) Attach the staple position label.
Attach the staple position label as shown in the figure.
∗
The label attachment position shown above is based on the corner
of the cabinet.
of the cabinet.
(6) Connect the finisher connector.
A. Remove the connector cover fixing screw for connection of the fin-
isher joint harness connector, and remove the connector cover.
B. Connect the finisher relay harness connector to the main unit con-
nector, and tighten the screw on the connector to fix.
(7) Turn ON the main power switch.
1) Insert the power plug of the main unit to the outlet.
2) Open the front cabinet, and open the power cover.
3) Turn ON the main power switch, close the power cover, and close
the front cabinet.
4) Turn ON the power switch on the right side of the main unit.
0.5mm
40mm
2mm
2mm
1
2
3
AR-M550/M620/M700 INSTALLATION MANUAL (AR-PN4) 5 - 1
[5] AR-PN4 UNPACKING AND INSTALLATION
1. Unpacking
(1) Removal of the main unit
(2) Removal of the fixing member
Packaged parts (accessories)
2. Installation
(1) Turn off the power of the main unit.
1) Turn OFF the power switch on the right side of the main unit.
2) Open the front cabinet, and turn OFF the main power switch.
3) Disconnect the power plug from the power outlet.
Punch position label
2 pcs.
AR-M550/M620/M700 INSTALLATION MANUAL (AR-PN4) 5 - 2
(2) Punch cover disassembly
1) Remove the punch cover fixing screws (6 pcs.), and lift the punch
cover slightly to remove it from the finisher.
2) Remove the fixing screw (1 pc.) of the punch cover front door from
inside of the punch cover.
3) Remove the cabinet B fixing screws (2 pcs.) on the rear side of the
finisher, and remove the rear cabinet B.
(3) Paper guide disassembly
1) Remove the paper guide fixing screw (1 pc.) and remove the paper
guide from the finisher.
(4) Punch unit assembly
1) Hang the punch unit on the step screws (2 pcs.) of the finisher and
assemble it.
2) Fix the punch unit with the paper guide fixing screw (1 pc.) which
was removed in step (3).
(5) Connector connection
1) Connect the punch joint harness connectors (2 pcs.) of the punch
unit to the connectors (2 positions) of the finisher PWB.
Click on the first or last page to see other MX-M700U (serv.man3) service manuals if exist.