Sharp MX-M364N / MX-565N (serv.man4) Service Manual ▷ View online
MX-M565N SIMULATION 5 – 21
25
25-1
Purpose
Operation test/check
Function (Purpose)
Check the operations of the developing
section, and to display the toner density
detection level.
section, and to display the toner density
detection level.
Section
Toner supply, developing
Operation/Procedure
1)
Press [EXECUTE] key.
The developing motor and the OPC drum motor rotate for 2
minutes and the output level of the toner density sensor is dis-
played.
minutes and the output level of the toner density sensor is dis-
played.
NOTE: The toner cartridge must be removed before executing this
simulation. If this simulation is executed with the toner car-
tridge installed, toner will be forcibly supplied to the devel-
oping unit, resulting in over toner and a trouble.
tridge installed, toner will be forcibly supplied to the devel-
oping unit, resulting in over toner and a trouble.
25-2
Purpose
Setting
Function (Purpose)
Make the initial setting of toner density
when replacing developer. (Automatic
adjustment)
when replacing developer. (Automatic
adjustment)
Section
Toner supply, developing
Operation/Procedure
1)
Press [EXECUTE] key.
The developing motor rotates for 2 minutes, and the toner density
sensor makes sampling of the toner density. The detected level is
displayed.
sensor makes sampling of the toner density. The detected level is
displayed.
After stopping the developing motor, the average value of the toner
density sampling results is set as the reference toner density con-
trol level.
density sampling results is set as the reference toner density con-
trol level.
NOTE: When the above operation is interrupted on the way, the
reference toner concentration level is not set. Also when
error code of EE-EC, EE-EL or EE-EU is displayed, the ref-
erence toner density level is not set normally.
error code of EE-EC, EE-EL or EE-EU is displayed, the ref-
erence toner density level is not set normally.
Do not execute this simulation unless new Developer material has
been installed. If it is executed in other cases, under toner or over-
tone may occur, causing a trouble.
been installed. If it is executed in other cases, under toner or over-
tone may occur, causing a trouble.
Adjustment result data display
Data display during execution
Display in case of an error
25-4
Purpose
Adjustment/Setting/Operation data check
Function (Purpose)
Display the operation data of the toner sup-
ply quantity (Not used in the market).
ply quantity (Not used in the market).
Section
Process
Operation/Procedure
The operation data of the toner supply quantity are displayed..
26
26-1
Purpose
Setting
Function (Purpose)
Set the paper exit operation from the right
side.
side.
Section
Paper exit section
Operation/Procedure
1)
Enter the set value with 10-key.
2)
Press [OK] key. (The set value is saved.)
This setting is required to use the paper exit tray unit
26-2
Purpose
Setting
Function (Purpose)
Set the paper type and the weight type.
Section
Paper feed, paper reverse/transport
Operation/Procedure
Select a paper size to be changed with the touch panel.
TCS_K
Toner sensor output value
TSG_K
Toner density sensor control voltage level
Item/Display
Content
AT DEVE ADJ_L_K
Toner density control adjustment value in the low
speed process mode.
speed process mode.
AT DEVE ADJ_M_K
Toner density control adjustment value in the
middle speed process mode
middle speed process mode
AT DEVE VO_L_K
Toner density sensor control voltage level in the
low speed process node
low speed process node
AT DEVE VO_M_K
Toner density sensor control voltage level in the
middle speed process mode
middle speed process mode
Item/Display
Content
TCS_K
Toner sensor output level
TSG_K
Toner density sensor control voltage level
Error display
Content
Details of content
EE-EL
EL abnormality
Sensor output level less than 77, or
sensor control voltage level over 207
sensor control voltage level over 207
EE-EU
EU abnormality
Sensor output level over 177, or sensor
control voltage level less than 52
control voltage level less than 52
EE-EC
EC abnormality
The sampling level in the automatic
toner density adjustment is outside of
128
toner density adjustment is outside of
128
3.
DV CTRG
Developer cartridge print counter
DV RANGE
Developer cartridge accumulated traveling
distance
distance
HUMIDITY AREA
Current humidity area
ALL VREF
All correction value for the toner density
reference value
reference value
DELTA VREF
Transition target correction amount
TONER DEN LT
Toner density output level
TONER DEN ST
Toner density standard level
AUTO DEVE VO
Toner density sensor control voltage
ALL V0
All correction values for the control voltage
value
value
HUM V0
Humidity correction amount
LIFE V0
Life correction amount
PROCON V0
Process control feedback correction amount
AREA V0
Area correction amount
PRINT RATE V0
Print ratio correction amount
ENV V0
Environment multiple correction amount
AUTO DEVE AREA
Humidity area
PRINT RATE V0
Print rate correction amount
Item/Display
Content
A
0
YES
Paper exit tray: YES
1
NO
Paper exit tray: NO
TRAY3
(TANDEM)
(TANDEM)
0
8.5 x 11
1
A4
2
B5
LCC
0
8.5 x 11
1
A4
2
B5
G/LBS SET
0
GRAM
1
LBS
Error display
Content
Details of content
MX-M565N SIMULATION 5 – 22
26-3
Purpose
Setting
Function (Purpose)
Set the specifications of the auditor
Section
Auditor
Operation/Procedure
Select an item to be set with the touch panel.
(*1) Displayed only when EQUITRAC.
(*2) Details of the vendor mode
Operation 1:
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Operation 2:
Auto clear is not made.
Auto clear is not made.
Operation 3:
The display is shifted to the initial screen.
The display is shifted to the initial screen.
26-5
Purpose
Setting
Function (Purpose)
Set the count mode in A3 (11" x 17") print.
Section
Operation/Procedure
1)
Select an item to be set with scroll key.
2)
Enter the setting value with 10-key
1 = Count up by 1, 2 = Count up by 2
1 = Count up by 1, 2 = Count up by 2
3)
Press [OK] key.
The set value in step 2) is saved.
26-6
Purpose
Setting
Function (Purpose)
Set the specifications of the destination.
Section
Operation/Procedure
1)
Select an item to be set with the touch panel.
2)
Press [EXECUTE] key.
The selected set content is saved.
26-7
Purpose
Setting
Function (Purpose)
Set the machine ID.
Section
Operation/Procedure
1)
Enter the machine ID with the 10-key.
Max. 30 digits of numerals and alphabetical characters can be
inputted. To select a desired character, press the 10-key
repeatedly. Refer to the following list and enter characters.
Touch the “CONFIRM” section every time a character is
inputted. To modify an inputted character, delete it with
“CLEAR” key and enter the correction character.
inputted. To select a desired character, press the 10-key
repeatedly. Refer to the following list and enter characters.
Touch the “CONFIRM” section every time a character is
inputted. To modify an inputted character, delete it with
“CLEAR” key and enter the correction character.
Item/Display
Content
Default
value
BUILT-IN
AUDITOR
AUDITOR
P10
Built-in auditor mode
(standard mode) operation.
(standard mode) operation.
P10
OUTSIDE
AUDITOR
AUDITOR
NONE
No external connection
vendor is used.
vendor is used.
NONE
P VENDOR1
Coin vendor mode
(Only the copy mode can be
controlled.)
(Only the copy mode can be
controlled.)
P VENDOR2
Vendor mode
communicating with the
parallel I/F (for DocuLyzer)
(Japan only)
communicating with the
parallel I/F (for DocuLyzer)
(Japan only)
P VENDOR3
Vendor mode in which
signals for the intercard
connected to the PCU are
used for communication in
parallel I/F.
signals for the intercard
connected to the PCU are
used for communication in
parallel I/F.
VENDOR-EX
(*1)
(*1)
Vendor I/F for EQUITRAC
VENDOR-EX
(MULTI) (*1)
(MULTI) (*1)
VENDOR-EX + Multi job
cueing Enable mode
cueing Enable mode
P OTHER
NOT USED
S_VENDOR
Serial vendor mode
DOC ADJ
ON
Support for the auditor in
document filing print
document filing print
OFF
OFF
No support for the auditor in
document filing print
document filing print
PF ADJ
ON
Continuous printing is
performed in the duplex print
mode.
If the remaining money
expires during continuous
printing, the sheets in the
machine are discharged
without being printed on the
back surfaces.
performed in the duplex print
mode.
If the remaining money
expires during continuous
printing, the sheets in the
machine are discharged
without being printed on the
back surfaces.
OFF
OFF
Continuous printing is not
performed in the duplex print
mode. (The remaining
amount is checked for
printing every surface in all
the printing process.)
If the remaining money
expires during printing, the
sheet is discharged without
printing on the back surface.
performed in the duplex print
mode. (The remaining
amount is checked for
printing every surface in all
the printing process.)
If the remaining money
expires during printing, the
sheet is discharged without
printing on the back surface.
VENDOR
MODE (*2)
MODE (*2)
MODE1
Vendor mode 1
MODE
3
MODE2
Vendor mode 2
MODE3
Vendor mode 3
COUNTUP
TIMING
TIMING
FUSER_IN
When the paper lead edge
passes the fusing rear
sensor.
passes the fusing rear
sensor.
EXIT_
OUT
FUSER_OUT
When the paper rear edge
passes the fusing rear
sensor.
passes the fusing rear
sensor.
EXIT_OUT
When the paper rear edge
passes the paper exit sensor
in the main unit, the right tray,
and the after process unit.
passes the paper exit sensor
in the main unit, the right tray,
and the after process unit.
IMS
CONTROL
CONTROL
ON
There is some restriction in
the image send mode.
the image send mode.
OFF
OFF
There is no restriction in the
image send mode.
image send mode.
VENDER
MODE
Completion of
the specified
quantity.
(Money
remaining)
Insufficient
money during
copy job
Completion of
the specified
quantity.
(No money
remaining)
remaining)
No money
remaining
remaining
Condition 1
Condition 2
Condition 3
MODE1
Operation 1
Operation 2
Operation 1
MODE2
Operation 1
Operation 1
Operation 1
MODE3
Operation 1
Operation 3
Operation 3
Item/Display
Content
Default value
A
TOTAL (B/W)
Total counter
2
B
MAINTE (B/W)
Maintenance counter
2
C
DEV (B/W)
Developer counter
U.S.A.
United States of America
CANADA
Canada
INCH
Inch series, other destinations
JAPAN
Japan
AB_B
AB series (B5 detection), other destinations
EUROPE
Europe
U.K.
United Kingdom
AUS.
Australia
AB_A
AB series (A5 detection), other destinations
CHINA
China
MX-M565N SIMULATION 5 – 23
2)
Press [SET] key to set the contents entered in procedure 1).
The machine ID can be set also by the Web Page service mode
function. Conventionally, the machine ID has been set by the Web
Page function. In this mode, this function is made available in the
simulation mode.
function. Conventionally, the machine ID has been set by the Web
Page function. In this mode, this function is made available in the
simulation mode.
26-8
Purpose
Setting
Function (Purpose)
Set the count mode (Long scale).
Section
Operation/Procedure
1)
Select an item to be set with scroll key.
2)
Enter the set value with 10-key
1 = Count up by 1, 2 = Count up by 2
1 = Count up by 1, 2 = Count up by 2
3)
Press [OK] key.
The set value in step 2) is saved.
Long Scale (Small) : 631 - 1050mm
Long Scale (Large) : 1051 - 1200mm
Long Scale (Large) : 1051 - 1200mm
26-10
Purpose
Setting
Function (Purpose)
Set the trial mode of the network scanner.
Section
Operation/Procedure
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
26-18
Purpose
Setting
Function (Purpose)
Set Disable/Enable of the toner save mode
operation.
(For the Japan and the UK versions.)
operation.
(For the Japan and the UK versions.)
Section
Operation/Procedure
1)
Select an item to be set with [UP] [DOWN] keys.
2)
Enter the set value with 10-key.
3)
Press [OK] key.
The set value in step 2) is saved.
26-30
Purpose
Setting
Function (Purpose)
Set the operation mode corresponding to
the CE mark (Europe safety standards).
the CE mark (Europe safety standards).
Section
Operation/Procedure
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
* Even in Enable state, the control may not be executed due
to the power frequency, etc.
10-key
Number of times of key input
1
2
3
4
5
6
7
8
9
10
1
1
-
-
-
-
-
-
-
-
-
2
A
B
C
a
b
c
2
-
-
-
3
D
E
F
d
e
f
3
-
-
-
4
G
H
I
g
h
i
4
-
-
-
5
J
K
L
j
k
l
5
-
-
-
6
M
N
O
m
n
o
6
-
-
-
7
P
Q
R
S
p
q
r
s
7
-
8
T
U
V
t
u
v
8
-
-
-
9
W
X
Y
Z
w
x
y
z
9
-
0
0
-
-
-
-
-
-
-
-
-
Item/Display
Content
Setting
range
Defaul
t value
Default
value
(Taiwan)
A
TOTAL(B/W)
LONG
SIZE(S)
LONG
SIZE(S)
Long scale (Small)
Total counter
Total counter
1 - 10
3
2
B
MAINTE
(B/W) LONG
SIZE(S)
(B/W) LONG
SIZE(S)
Long scale (Small)
Maintenance
counter (B/W)
Maintenance
counter (B/W)
1 - 10
3
2
C
DEV(B/W)
LONG
SIZE(S)
LONG
SIZE(S)
Long scale (Small)
Developer counter
(B/W)
Developer counter
(B/W)
1 - 10
3
2
D
TOTAL(B/W)
LONG
SIZE(L)
LONG
SIZE(L)
Long scale (Large)
Total counter (B/W)
Total counter (B/W)
1 - 10
5
2
E
MAINTE
(B/W) LONG
SIZE(L)
(B/W) LONG
SIZE(L)
Long scale (Large)
Maintenance
counter (B/W)
Maintenance
counter (B/W)
1 - 10
5
2
F
DEV(B/W)
LONG
SIZE(L)
LONG
SIZE(L)
Long scale (Large)
Developer counter
(B/W)
Developer counter
(B/W)
1 - 10
5
2
TRIAL MODE
(0: YES 1: NO)
0
Trial mode setting
1
Trial mode cancel (Default)
Item
Display
Content
Default
value
A
COPY
0
Copy toner save mode is inhibited.
0
1
Copy toner save mode 1
2
Copy toner save mode 2
3
Copy toner save mode 3
B
PRINTER
0
Printer toner save mode is inhibited.
0
1
Printer toner save mode 1
2
Printer toner save mode 2
3
Printer toner save mode 3
C
COPY TS
DISPLAY
DISPLAY
0
Toner save setting is displayed
Refer
to the
destinat
ion list
below
to the
destinat
ion list
below
1
Toner save setting is not displayed
D
PRINTER
TS
DISPLAY
TS
DISPLAY
0
Toner save setting is displayed
1
Toner save setting is not displayed
Destination
Default value C
Default value D
U.S.A
0 (Displayed)
0 (Displayed)
CANADA
0 (Displayed)
0 (Displayed)
INCH
0 (Displayed)
0 (Displayed)
JAPAN
1 (Not Displayed)
0 (Displayed)
AB_B
0 (Displayed)
0 (Displayed)
EUROPE
0 (Displayed)
0 (Displayed)
U.K.
1 (Not Displayed)
0 (Displayed)
AUS.
0 (Displayed)
0 (Displayed)
AB_A
0 (Displayed)
0 (Displayed)
CHINA
0 (Displayed)
0 (Displayed)
0
Control allowed
1
Control inhibited
U.S.A
1 (CE not supported)
EUROPE
0 (CE supported)
CANADA
1 (CE not supported)
U.K.
0 (CE supported)
INCH
1 (CE not supported)
AUS.
0 (CE supported)
JAPAN
1 (CE not supported)
AB_A
0 (CE supported)
AB_B
1 (CE not supported)
CHINA
0 (CE supported)
2
: ‘16/Jan
2
MX-M565N SIMULATION 5 – 24
26-32
Purpose
Setting
Function (Purpose)
Set the specifications of the fusing cleaning
operation.
operation.
Section
Fusing
Operation/Procedure
1)
Enter the set value with 10-key.
2)
Press [OK] key.
26-35
Purpose
Setting
Function (Purpose)
Set the display mode of SIM22-4 trouble
history when a same trouble occurred
repeatedly. There are two display modes:
display as one trouble or display as several
series of troubles.
history when a same trouble occurred
repeatedly. There are two display modes:
display as one trouble or display as several
series of troubles.
Section
Operation/Procedure
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
26-38
Purpose
Setting
Function (Purpose)
Set "Print continue" or "Print stop" when the
maintenance timing is reached or the con-
sumable part life is over.
maintenance timing is reached or the con-
sumable part life is over.
Section
Operation/Procedure
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
26-41
Purpose
Setting
Function (Purpose)
Set Enable/Disable of the magnification
ratio automatic select function (AMS) in the
center binding mode.
ratio automatic select function (AMS) in the
center binding mode.
Section
Operation/Procedure
1)
Enter the set value with 10-key.
2)
Press [OK] key.
The set value in step 1) is saved.
<Default value of each destination>
26-49
Purpose
Setting
Function (Purpose)
Set the print speed of postcards mode.
Section
Operation/Procedure
Select the copy speed mode with the touch panel. (Default: LOW)
When the setting is changed, the paper feed interval in print or
copy in the postcard mode is changed and the job speed is
changed accordingly.
copy in the postcard mode is changed and the job speed is
changed accordingly.
LOW: The paper feed interval is long. (Normal mode)
HIGH: The paper feed interval is short. (when a paper jam occurs,
the number of sheets of jam paper is greater than that in the LOW
mode.)
the number of sheets of jam paper is greater than that in the LOW
mode.)
26-50
Purpose
Setting
Function (Purpose)
Set the operation specifications and func-
tions.
tions.
Section
Operation/Procedure
1)
Select a target item of setting with scroll key on the touch
panel.
panel.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (The set value is saved.)
(*1) Default values for each destination of item A
Item
Display
Content
Default
value
A
CLEANING
PRINT SET
PRINT SET
0
User fusing cleaning function is
Enabled
Enabled
1
1
User fusing cleaning function is
Disabled
Disabled
0
Only once display.
1
Any time display.
Item/Display
Content
Default
value
A
MAINTENANCE
LIFE OVER
LIFE OVER
0
When the maintenance life is
over (Print Continue)
over (Print Continue)
0
1
When the maintenance life is
over (Print Stop)
over (Print Stop)
B
FUSER WEB END
(0: CONTINUE
1: STOP)
(0: CONTINUE
1: STOP)
0
Continue/Stop setting of print
when the fusing web is end
(Print Continue)
when the fusing web is end
(Print Continue)
0
1
Continue/Stop setting of print
when the fusing web is end
(Print Stop)
when the fusing web is end
(Print Stop)
0
AMS Disable
1
AMS Enable
U.S.A
0 (Disable)
EUROPE
1 (Enable)
CANADA
0 (Disable)
U.K.
1 (Enable)
INCH
0 (Disable)
AUS.
0 (Disable)
JAPAN
0 (Disable)
AB_A
0 (Disable)
AB_B
0 (Disable)
CHINA
0 (Disable)
Item/Display
Content
Default
value
A
BW REVERSE
0
BW reverse copy Disable
Refer
to *1
1
BW reverse copy Enable
B
FINISHER
FUNCTION
FUNCTION
0
Finisher special paper
The number of paper exit is
limited.
The number of paper exit is
limited.
0
Refer
to *2
1
Finisher special paper
The number of paper exit is
not limited.
The number of paper exit is
not limited.
C
FEED TRAY
COLOR
COLOR
0
Paper feed tray color display
ON during paper feed
ON during paper feed
0
1
Paper feed tray color display
OFF during paper feed
OFF during paper feed
D
LONG SIZE PRINT
0
Disable
0
1
Enable
E
WIRELESS SET
0
Disable
0
1
Enable
Destination
Item A
U S A
1
CANADA
1
INCH
1
JAPAN
1
AB_B
1
EUROPE
1
U K
0
AUS
1
AB_A
1
CHINA
1
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.