Sharp MX-M364N / MX-565N (serv.man4) Service Manual ▷ View online
MX-M565N SIMULATION 5 – 5
44
6
Execute the high density process control forcibly.
Process
9
Display the result data of the high density process control operation.
Image process
12
Display the operation data of the high density process control and the image density
sensor.(registration sensor)
sensor.(registration sensor)
Image process
14
Display the output level of the temperature and humidity sensor.
Process
15
Set the OPC drum idle rotation.
Process
17
Process refresh execution
21
Set the halftone process control target.
Process
22
Display the toner patch density level in the half tone process control operation.
Process
24
Display the correction target and the correction level in the half tone process control operation.
Process
25
Set the calculating conditions of the correction value for the half tone process control.
Process
26
Execute the half tone process control compulsory.
Process
27
Clear the correction data of the half tone process control.
Process
28
Set the process control execution conditions.
Process
29
Set the operating conditions of the process control during a job.
Process
34
Set the process control execution conditions.
Process
37
Set the development bias correction level in the continuous printing operation.
Toner supply, developing
43
Display the identification information of the developing unit.
Developing
62
Set the process control execution conditions
Process
46
2
Adjust the copy density in each copy mode.
4
Adjust the density in the image send mode (color mode)
5
Adjust the density in the image send mode (monochrome mode).
8
Adjust the image send mode color balance RGB.
9
Adjust scan image density (copy, image send mode)
10
Adjust the copy density (in each copy mode).
16
Adjust the copy density and gamma.
19
Set the operating conditions of document density scanning (copy, image send mode).
Scanner
23
Set the density correction of copy high density section (High density tone gap supported).
24
Copy half tone adjustment (Auto adjustment)
32
Adjust the document background density reproductivity in the auto copy mode.
37
Adjust the reproduction capability of the scan image color document (copy, image send mode).
39
Adjust the sharpness of FAX send images.
40
Adjust the FAX send image density. (Collective adjustment of all the modes)
41
Adjust the FAX send image density. (Normal)
42
Adjust the FAX send image density. (Fine)
43
Adjust the FAX send image density. (Super Fine)
44
Adjust the FAX send image density. (Ultra fine)
45
Adjust the FAX send image density. (600dpi).
46
Adjust the FAX send image density (RGB RIP)
47
Set the JPEG compression rate in copy and scan images.
48
Set the output resolution in each copy mode.
51
Adjust the gamma for copy, heavy paper mode and image process mode (manual adjustment).
52
Set the gamma default for the copy mode heavy paper and the image process mode. (After
execution of either SIM46-54 or SIM46-51 the adjustment value is reset to the initial value)
execution of either SIM46-54 or SIM46-51 the adjustment value is reset to the initial value)
54
Perform the engine halftone automatic density adjustment (dither)
55
Adjust the drop out color in the image send mode (monochrome manual text mode)
58
Set the copy mode pseudo resolution (smoothing process)
59
Perform the copy mode pseudo resolution image process adjustment
60
Adjust the sharpness in the color auto mode
61
Adjust the area separation recognition level in image send mode (color, gray, auto exposure mode).
62
Set the operating conditions of the ACS, the area separation, the background image process, and
the auto exposure mode.
the auto exposure mode.
63
Adjust the density in the copy low density section.
66
Adjust the reproduction capability of watermark in the copy/printer mode.
74
Adjust copy gray balance (Auto adjustment) / printer gray balance (Auto adjustment)
90
Set the process operation of high-compression PDF images.
91
Adjust the reproduction capability of black text.
48
1
Adjust the scan image magnification ratio (main scanning direction and sub scanning direction).
Scanner
5
Correction the scan image magnification ratio (sub scanning direction).
Scanner
6
Adjust the rotation speed of each motor.
49
1
Perform the firmware update.
3
Update the operation manual data stored in the HDD.
5
Update the watermark data stored in the HDD.
10
Perform the ACU firmware update.
50
1
Copy image position, image loss adjustment
5
Adjust the print lead edge image position. (PRINTER MODE)
6
Adjust the copy image position and the image loss (SPF mode).
7
Adjust DSPF document lead edge (simple method) and copy image position on print paper and the
void area (image loss) in the copy mode.
void area (image loss) in the copy mode.
10
Adjust the image off-center position.
(The adjustment is made separately for each paper feed section.)
(The adjustment is made separately for each paper feed section.)
Main
Sub
Functions
Section
MX-M565N SIMULATION 5 – 6
50
12
Perform the scan image off-center position adjustment.
(The adjustment is made separately for each scan mode.)
(The adjustment is made separately for each scan mode.)
27
Adjust the image loss of a scan image in the FAX/scanner mode.
28
Perform the OC adjustment, main scan magnification ration correction, the SPF adjustment and the
print position adjustment.
print position adjustment.
51
1
Adjust the ON/OFF timing of the transfer voltage
2
Adjust the contact pressure (deflection amount) on paper by the main unit and the SPF resist roller.
Paper feed, paper reverse/transport
53
6
Used to adjust the detection level of the SPF document width.
7
Used to adjust the SPF document size width sensor.
Automatic document feeder
8
Used to adjust the document lead edge reference and the SPF mode document scan position.
Automatic document feeder
9
SPF dirt detection setting.
10
SPF dirt detection execution.
55
1
Set the specifications of the engine control operations. (SOFT SW)
2
Set the specifications of the scanner control operation. (SOFT SW)
3
Set the specifications of the controller operation. (SOFT SW)
56
1
Transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.)
2
Backup the data in the EEPROM. SRAM, and HDD (including user authentication data and address
data) to the USB memory.
data) to the USB memory.
3
Backup the document filing data to the USB memory.
HDD
4
Backup the JOB log data to the USB memory.
HDD
5
Import the SIM22-6 data to the USB memory in the TEXT format.
6
Import the SIM23-2 data to the USB memory in the TEXT format.
7
Import SYSLOG data into the USB memory.
60
1
Check the operations (read/write) of the MFP PWB memory.
MFP (ICU) PWB
61
1
Check the LSU polygon motor rotation and laser detection.
LSU
3
Set the laser power
LSU
4
Print the print image skew adjustment pattern
11
Correct the laser power automatically
12
Laser power manual correction LSU.
13
Clear the laser power correction value.
62
1
Format HDD/SD card (HDD: excluding the operation manual and the watermark data) (SD card
user data).
user data).
HDD
2
Check read/write of the hard disk (partial).
HDD
3
Check read/write of the hard disk (all areas).
HDD
6
Perform the self diagnostics of the hard disk.
HDD
7
Print the hard disk self diagnostics error log.
HDD
8
Format the HDD/SD card (HDD: excluding the operation manual , watermark data and the system
area) (SD card: user data)
area) (SD card: user data)
HDD
10
Clear the job completion list .
HDD
11
Clear the document filing data.
HDD
12
Set Enable/Disable of auto format in a hard disk trouble.
HDD
13
Format the hard disk. (operation manual and watermark area only)
HDD
14
Delete the document filing management data.
20
Check the operation of the mirroring HDD.
Mirroring HDD
63
1
Used to display the shading correction result.
Scanner
2
Used to perform shading.
Scanner
3
Used to perform scanner (CCD) color balance and gamma auto adjustment.
Scanner
4
Used to display the SIT chart patch density.
Scanner
5
Used to perform the scanner (CCD) color balance and gamma default setting.
Scanner
11
Set the target color balance of the copy mode.
64
2
Test print. (Self print) (Monochrome mode)
4
Printer test print. (Self print)
* This simulation functions only for the machines which are provided with the printer function.
* This simulation functions only for the machines which are provided with the printer function.
5
Printer test print. (Self print) (PCL)
6
Printer test print. (Self print) (PS)
65
1
Adjust the touch panel (LCD display section) detection coordinates.
Operation unit
2
Display the touch panel (LCD display section) detection coordinates.
Operation unit
5
Check the operation panel key input.
Operation unit
67
17
Printer controller reset
24
Printer density adjustment (auto adjustment)
25
Printer density adjustment (Manual adjustment)
26
Set the target the halftone of the printer mode
31
Clear the printer calibration value (Half-tone process control data).
33
Set the gamma of the each printer screen.
34
Set the density correction in the printer high density section.
(Support for the high density section tone gap)
(Support for the high density section tone gap)
36
Adjust the density in the low density section.
45
Adjust the printer image filter.
52
Set the default of the gamma of the printer screen.
54
Printer engine halftone auto adjustment.
Main
Sub
Functions
Section
MX-M565N SIMULATION 5 – 7
3. Details of simulation
1
1-1
Purpose
Operation test/check
Function (Purpose)
Check the operation of the scanner (read-
ing) unit and the control circuit.
ing) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
Select the operation resolution (scan speed) with the touch
panel key.
panel key.
2)
Press [EXECUTE] key.
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
scan resolution (operation speed).
1-2
Purpose
Operation test/check
Function (Purpose)
Check the sensors in the scanner (reading)
section and the related circuits.
section and the related circuits.
Section
Scanner
Operation/Procedure
The operating status of the sensor is displayed. When "MHPS" is
highlighted, the scanner unit is in the home position.
highlighted, the scanner unit is in the home position.
1-5
Purpose
Operation test/check
Function (Purpose)
Check the operation of the scanner (read-
ing) unit and the control circuit.
ing) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
Select the operation speed with the touch panel key.
2)
Press [EXECUTE] key.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed). When [EXECUTE] key is
pressed, the operation is terminated.
resolution (operation speed). When [EXECUTE] key is
pressed, the operation is terminated.
2
2-1
Purpose
Operation test/check
Function (Purpose)
Check the operations of the automatic doc-
ument feed unit and the control circuit.
ument feed unit and the control circuit.
Section
Automatic document feeder
Operation/Procedure
1)
Select the operation mode and the speed with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The DSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).When [EXECUTE] key is pressed, the operation
is terminated.
ations at the speed corresponding to the scan resolution (oper-
ation speed).When [EXECUTE] key is pressed, the operation
is terminated.
DSPF
RSPF
2-2
Purpose
Operation test/check
Function (Purpose)
Check the operations of the sensors and
the detectors in the document feed unit
section and the control circuits.
the detectors in the document feed unit
section and the control circuits.
Section
Automatic document feeder
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played. The code names of the sensors and the detectors which
are active are highlighted.
played. The code names of the sensors and the detectors which
are active are highlighted.
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI
(372mm/s)
(372mm/s)
400DPI
400DPI (279mm/s)
600DPI
600DPI (186mm/s)
1200DPI
1200DPI (93mm/s)
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI
(372mm/s)
(372mm/s)
400DPI
400DPI (279mm/s)
600DPI
600DPI (186mm/s)
1200DPI
1200DPI (93mm/s)
Item/Display
Operation mode
Default value
(SINGLE)
300DPI
300DPI (372mm/s)
300DPI
(372mm/s)
(372mm/s)
400DPI
400DPI (279mm/s)
600DPI
600DPI (186mm/s)
(DOUBLE)
300DPI
300DPI (372mm/s)
300DPI
(372mm/s)
(372mm/s)
400DPI
400DPI (279mm/s)
600DPI
600DPI (186mm/s)
Item/Display
Operation mode
Default value
(SINGLE)
300DPI
300DPI (279mm/s)
300DPI
(279mm/s)
(279mm/s)
400DPI
400DPI (279mm/s)
600DPI
600DPI (186mm/s)
(DOUBLE)
300DPI
300DPI (279mm/s)
300DPI
(279mm/s)
(279mm/s)
400DPI
400DPI (279mm/s)
600DPI
600DPI (186mm/s)
SSET
SPF installation detector
SOCD
SPF open/close detector
SCOV
SPF upper door open/close detector
SLCOV
SPF lower door open/close sensor
SPED1
SPF document upper limit detector
SPED2
SPF document empty detector
SPPD1
SPF document pass detector 1
(Paper entry detection)
(Paper entry detection)
SPPD2
SPF document pass detector 2
(Resist roller front document transport detection)
(Resist roller front document transport detection)
SPPD3
SPF document pass detector 3
(Document scanning front document transport detection)
(Document scanning front document transport detection)
SPPD4
SPF document pass detector 4
SPPD5
SPF document pass detector 5
(Document transport detection)
(Document transport detection)
SPOD
SPF document exit detector
SPRDMD
SPF document random detector
SPLS1
SPF document length detection short detector
SPLS2
SPF document length detection long detector
STLD
SPF document feed tray lower limit detector
STUD
SPF document feed tray upper limit detector
STMPU
SPF stamp unit installation detector
SWD_LEN
SPF guide plate position (Unit: 0.1mm)
SWD_AD
SPF document detection volume output AD value
MX-M565N SIMULATION 5 – 8
2-3
Purpose
Operation test/check
Function (Purpose)
Check the operations of the loads in the
automatic document feed unit and the con-
trol circuit.
automatic document feed unit and the con-
trol circuit.
Section
Automatic document feeder
Operation/Procedure
1)
Select a target item of the operation check with the touch panel
key.
key.
2)
Press [EXECUTE] key.
The selected load performs the operation. When [EXECUTE]
key is pressed, the operation is terminated.
key is pressed, the operation is terminated.
3
3-2
Purpose
Operation test/check
Function (Purpose)
Check the operations of the sensors and
the detectors in the finisher and the control
circuit.
the detectors in the finisher and the control
circuit.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played. The code names of the sensors and the detectors which
are active are highlighted.
played. The code names of the sensors and the detectors which
are active are highlighted.
<Inner finisher / Punch module>
<1K Saddle stitch finisher / Punch module>
<4K Finisher>
SPUM
SPF document feed motor
SPFM
SPF transport motor
SPOM
SPF document exit motor
SLUM
SPF lift up motor
SPFFAN
SPF cooling fan motor
SPFC
SPF document feed clutch
SRRC
SPF No2 registration roller clutch
STRRC
SPF No1 registration roller clutch
STRC
SPF transport roller clutch
STMPS
Stamp solenoid
(Displayed only when the finish stamp is installed.)
(Displayed only when the finish stamp is installed.)
FABHS
Paper alignment belt HP sensor
FAPHPS_F
Paper alignment plate HP sensor F
FAPHPS_R
Paper alignment plate HP sensor R
FDRPS
Paper exit roller position sensor
FDTLLS
Paper exit tray lower limit sensor
FDTPD
Delivery tray paper detector
FDTULS
Paper exit tray upper limit sensor
FFL
Fan lock signal
FPLD1
Paper height sensor 1
FPLD2
Paper height sensor 2
FPPD1
Paper entry sensor
FSED
Staple empty sensor
FSHPS
Staple HP sensor
FSLD
Staple lead edge sensor
FSSHPS
Staple shift home position sensor
FSSS
Staple safety sensor
FSSW
Safety switch
FSTPD
Staple tray paper sensor
FTPS
Tray position sensor
FPCHPS
Punch home position sensor
FPD
Punch unit sensor (connector)
FPDFS
Punch dust sensor
FPES1
Punch paper edge sensor 1
FPES2
Punch paper edge sensor 2
FPES3
Punch paper edge sensor 3
FPES4
Punch paper edge sensor 4
FPES5
Punch paper edge sensor 5
FPES6
Punch paper edge sensor 6
FPES7
Punch paper edge sensor 7
FPHPS
Punch unit home position sensor
FPMRS
Punch motor rotation sensor
FPMS
Punch mode sensor
FPTS
Punch timing sensor
PDPPD1
FJPID
Paper pass paper transport detector 1
PDPPD2
FJPOD
Paper pass paper transport detector 2
PDCS
FJPDD
Paper pass cover Open/Close sensor
FPPD1
FED
Paper delivery detector 1
FPAPHS_F
FFJHPD
Paper alignment plate home position sensor F
FPAPHS_R
FRJHPD
Paper alignment plate home position sensor R
FATPD
FAD
Paper alignment tray paper detector
FGHPS
FGHPD
Gripper home position sensor
FDTPD
EMPS
Delivery tray paper detector
FPLD
FSLD
Paper surface detector
FPPD2
FFPD
Paper transport detector 2
FSPHS
FFHPD
Saddle plate home position sensor
FSTPD
FFED
Saddle exit tray paper detector
FSMRS
FFE
Saddle motor rotation sensor
FTULD
FULD
Tray upper limit detector
FTLLD
FLLD
Tray lower limit detector
FTLMRS
FLE
Tray lift motor rotation sensor
FSHS
FSHPD
Staple home position sensor
FSSHPS
FSTHPD
Stapler shift home position sensor
FSED
FSD
Staple empty detector
FSLS
FSPD
Staple lead edge sensor
FTPS
FMLD
Tray position sensor
FCD1
FFDD
Cover detector 1
FCD2
FCD
Cover detector 2
FSSW1
FFDDW
Safety switch 1
FCD
FJSW
Finisher connection detector
FSSSW1
FSSSW
Staple safety switch
FFL
FFANLK
Fan lock signal
FDRHS
FNHPD
Delivery roller home position sensor
FPPD3
FSPOD
Paper transport detector 3
FSATPD
FSDTPD
Saddle paper alignment tray paper detector
FSSSW2
FSJPD
Stapler safety switch 2
FPHHD
FPHHPD
Paper hold home position sensor
FSAPHS
FSJHPD
Saddle alignment plate home position sensor
FSPGHS
FAHPD
Saddle paper guide home position sensor
FSRHS
FSR3HPD
Saddle roller home position sensor
FPDD
FGED
Delivery detector
FSSHS
FSSHPD
Saddle staple home position sensor
FSSES
FSSD
Saddle staple sensor
FSSCS
FSSDSW
Saddle staple cover sensor
FSSSHS
FSSTHPD
Finisher saddle stapler shift home position
sensor
sensor
FPMRS
FPMCK
Punch motor rotation sensor
FPD
FPUC
Punch unit detection (connector)
FPCHPS
FPHPD
Punch home position sensor
FPDFS
FPDD
Punch dust sensor
FPHPS
FPSHPD
Punch unit home position sensor
FPTS
FPTD
Punch timing sensor
FPES1
FPSD1
Punch paper edge sensor 1
FPES2
FPSD2
Punch paper edge sensor 2
FPES3
FPSD3
Punch paper edge sensor 3
FPES4
FPSD4
Punch paper edge sensor 4
FPPS
FPPD
Punch paper position sensor
FJPID
Interface transport unit entry port detection
FJPOD
Interface transport unit exit port detection
FJPDD
Interface transport unit cover detection
FED
Entry port paper detection
FAED1
Tray 1 area detection 1
FAED2
Tray 1 area detection 2
FAED3
Tray 1 area detection 3
FFJHPD
Alignment plate HP detection front
FRJHPD
Alignment plate HP detection rear
FBED1
Tray 1 paper detection
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.