Sharp MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) Service Manual ▷ View online
MX-M503N MX-KBX2 23 – 1
MX-M503N
Service Manual
[23] MX-KBX2
* This option cannot be installed to the following models.
MX-M363U/M453U/M503U
MX-M282N/M362N/M452N/M502N
MX-M282N/M362N/M452N/M502N
1. Unpacking
A. Check the parts in the package
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main
unit.
Turn OFF the power switch in the front cabinet of the main
unit.
3)
Disconnect the power plug of the main unit from the power out-
let.
let.
B. Install the USB hub PWB.
1)
Remove the screw, and remove the rear cabinet.
No.
Name of parts in the package
Quantity
1
Keyboard unit
1
2
Operation base plate C
1
3
USB hub PWB unit
1
4
Mother PWB connection harness
1
5
Fixing screw A (M4 x 8 S tight)
3
6
Fixing screw B (M3 x 8 3-point system)
1
7
Protection sheet
1
8
Black sheet
1
9
Installing Procedures
1
1
1
2
5
6
7
8
9
3
4
OFF
1
2
: '10/Jun/18
1
MX-M503N MX-KBX2 23 – 2
2)
Disconnect the connector of the scan mother harness, and
remove the screws.
remove the screws.
3)
Attach the USB hub PWB unit (part No.3 in the package) with
the removed screws.
the removed screws.
4)
Connect the connector of the scan mother harness, and con-
nect the mother PWB connection harness (part No.4 in the
package).
nect the mother PWB connection harness (part No.4 in the
package).
5)
Attach the rear cabinet, and fix it with the screws.
C. Install the base unit
1)
Place the protection sheet (part No.7 in the package) on the
table glass.
table glass.
2)
Open the front cabinet, and remove the screw, and remove the
front cabinet upper.
front cabinet upper.
3)
Remove the screw, and remove the operation base plate unit.
1
2
MX-M503N MX-KBX2 23 – 3
4)
Remove the screws and disconnect two connectors. Place the
operation panel upside down on the protection sheet.
operation panel upside down on the protection sheet.
*1: Don't pull the lead wire. The connector can be locked.
Hold the housing section of connector, pull out it.
*2: Slowly pull the lead wire and disconnect the connector.
*3: There is a locking section on the reverse side. Use care for
*3: There is a locking section on the reverse side. Use care for
that.
5)
Remove the screw, and remove the panel angle.
6)
Install the keyboard unit (part No.1 in the package), and fix it
with the fixing screw A (part No.5 in the package) and the fixing
screw B (part No.6 in the package).
* When fixing the fixing screw B, use the short screwdriver or
with the fixing screw A (part No.5 in the package) and the fixing
screw B (part No.6 in the package).
* When fixing the fixing screw B, use the short screwdriver or
the small screwdriver.
D. Install the operation panel
1)
Check that each harness is engaged with the rib.
2)
Connect the connector.
3)
Install the operation panel to the main unit, and fix it with the
screw.
screw.
*1: Be careful to the place of the connector lock, it is on the
other side.
*2: Insert the connector all the way.
4)
Remove the screw, and remove the operation base plate B
from the operation base plate unit.
from the operation base plate unit.
*1 *3
*2
*1
*2
MX-M503N MX-KBX2 23 – 4
5)
Slide and attach the operation base plate C (part No.2 in the
package) to the operation base plate unit.
package) to the operation base plate unit.
6)
Install the operation base plate unit to the main unit, and fix it
with the screws.
with the screws.
7)
Attach the front cabinet upper, and fix it with the screws.
E. Adjust the position of the key top unit
1)
When the cabinet position of the key top unit is shifted, loosen
the screws which are fixing the key top unit and adjust the
position up and down. Then tighten the screws.
the screws which are fixing the key top unit and adjust the
position up and down. Then tighten the screws.
F. Turn on the power of the main unit
1)
Insert the power plug of the main unit into the power outlet.
2)
Turn ON the power switch inside the front cabinet.
3)
Turn ON the power switch on the operation panel.
G. Check the keyboard input
1)
Touch [IMAGE SEND] on the touch panel.
2)
Touch [SEND SETTING] on the touch panel.
3)
Touch [FILE NAME/DIRECT ENTRY] on the touch panel.
4)
Enter the keyboard input, and check the input on the touch
panel.
panel.
H. Language setting
Targets:
The model for 8.5 inch LCD panel with option keyboard installed.
The language selected should be the same as the layout of the
option keyboard, otherwise false input occur.
1)
The model for 8.5 inch LCD panel with option keyboard installed.
The language selected should be the same as the layout of the
option keyboard, otherwise false input occur.
1)
Press the [SYSTEM SETTINGS] key.
The following menu screen appears on the touch panel.
The following menu screen appears on the touch panel.
2)
Touch [Default Settings].
ON
JOB STATUS
IMAGE SEND
HOME
PRINT
READY
DATA
DATA
DATA
LINE
SYSTEM
SETTINGS
LOGOUT
Admin Password
Exit
Total Count
Paper Tray
Settings
Printer Condition
Settings
Document Filing
Control
Address Control
Fax Data
Receive/Forward
USB-Device Check
Default Settings
List Print
(User)
S
Sy
ys
st
te
em
m S
Se
et
tt
ti
in
ng
g
Click on the first or last page to see other MX-M363N / MX-M363U / MX-M503N / MX-M503U (serv.man18) service manuals if exist.