Sharp MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man5) Handy Guide ▷ View online
Firmware Upgrade Procedure
17
Document Solutions After Sales Service
1) Insert the media or USB memory which stores the firmware into the main
unit. (Be sure to use the USB I/F on the operation panel.)
2) Enter the SIM49-01.Press the key of the file to be updated. The screen
transfers to the update screen.
3) Current version number and the version number to be updated will be
shown for each firmware respectively.
4) Press [ALL] key. All the firmware programs are selected.
5) Press [EXECUTE] key. “ARE YOU SURE? [YES] [NO]”becomes clear. Press
[YES] key to start the update of selected firmware.
Progress is displayed on right side of "FIRMWAREUPDATE" title by 20 steps.
6) If the update is normal completion, following screen is dis-played. Press
[OK] key. (The machine is rebooted.) Go to SIM22-05 and confirm the
firmware has upgraded successfully.
firmware has upgraded successfully.
Refer to the Service Manual Section 8 for more information.
Test Simulations
18
Document Solutions After Sales Service
Entering simulation mode
Perform the following procedure to enter the simulation mode.
Main Sub Functions
1
1
1
Check the operation of the scanner (reading) unit and the control circuit.
2
Check the sensors in the scanner (reading) section and the related circuits.
5
Check the operation of the scanner (reading) unit and the control circuit.
2 1 Check
the
operations
of
the automatic document feeder
2
Check the operations of the sensors and the detectors in the automatic document
feeder section and the control circuits.
feeder section and the control circuits.
3
Check the operations of the loads in the automatic document feeder.
3
2
Check the operations of the sensors and the detectors in the finisher.
3
Check the operation of the load in the finisher and the control circuit.
10
Adjust the finisher.
4
2
Check the operations of the sensors and detectors in the desk.
3
Check the operations of the loads in the desk.
5
Check the operations of the paper feed desk paper transport clutch.
5
1
Check the operation of the display, LCD in the operation panel.
2
Check the operation of the heater lamp and the control circuit.
3
Check the operation of the scanner lamp and the control circuit.
6
1
Check the operations of the load in the paper transport system.
2
Check the operations of each fan motor and its control circuit.
90
Reset the machine to the factory setting.
7
1
Set the operating conditions of aging.
6
Set the operating intermittent aging cycle.
8
Display the warm-up time.
12
Document reading number of sheets setting (for aging operation)
8 1 Check
and
adjust
the
operations of the developing voltage.
2
Check and adjust the operation of the main charger grid voltage.
6
Check the output of the transfer charger output voltage.
9 2 Check
the
operations
of
the sensors and detectors in the paper reverse section.
3
Check the operations of the load in the paper reverse section.
Test Simulations
19
Document Solutions After Sales Service
Main Sub Functions
10
10
1
Check the operations of the toner supply mechanism (toner motor).
13
-
Cancel the self-diag "U1" trouble.
14
-
Cancel the self-diag H3, H4, H5 troubles.
16
-
Cancel the self-diag "U2" trouble. MFP PWB / PCU PWB / SCU PWB
17
-
Cancel the self-diag "PF" trouble.
21
1
Set the maintenance cycle.
22
1
Check the print count value in each section and each operation mode.
2
Check the total number of misfeed and troubles.
3
Check misfeed positions and the misfeed count of each position.
5
Check the ROM version of each unit (section).
6 Output
the
setting/adjustment data (simulation, FAX soft switch, counter).
8
Check the number of operations (counter value) of the finisher, the RSPF.
9
Check the number of use (print quantity) of each paper feed section.
10
Check the system configuration (option, internal hardware).
11
Check the use frequency (send/receive) of FAX. (Only when FAX is installed).
12
Check the RSPF misfeed positions and the number of misfeed at each position.
13
Check the operating time of the process section.
14
Display the use status of the toner cartridge.
18
Display the user data delete history.
19
Check the values of the counters related to the scan - image send.
40
Display the error code list and the contents.
90
Output the various set data lists.
23
2
Output the trouble history list of paper jam and misfeed.
80
Check the operation of paper feed and paper transport in the paper feed section
and the paper transport section. Used to output the list of the operation status of
the sensor and the detectors in the paper feed section and the paper transport
section.
and the paper transport section. Used to output the list of the operation status of
the sensor and the detectors in the paper feed section and the paper transport
section.
24
1
Clear the jam counter, and the trouble counter.
2
Clear the number of use (the number of prints) of each paper feed section.
3
Clear the finisher, RSPF, and the scan (reading) unit counter.
4
Clear the maintenance counter, the printer counters of the transport unit and the
fusing unit. (After completion of maintenance, clear the counters.)
fusing unit. (After completion of maintenance, clear the counters.)
5
Clear the developer counter. (After replacement of developer, clear the counter.)
6
Clear the copy counter.
9
Clear the printer mode print counter and the self print mode print counter.
10
Clear the FAX counter. (Only when FAX is installed)
12
Clear the document filing counter value.
Test Simulations
20
Document Solutions After Sales Service
Main Sub Functions
24
15
Clear the counters related to the scan mode and the image send.
30
Initialize the administrator (Admin) password.
31
Initialize the service mode password.
35
Clear the toner cartridge use status data.
25
1
Check the operations of the developing section.
2
Make the initial setting of toner density when replacing developer. (Automatic
adjustment)Image process (Photoconductor/Developing)
adjustment)Image process (Photoconductor/Developing)
4
Display the operation data of the toner correction
26
1
Set Yes/No of installation of the job separator.
2
Set the paper size of the paper feed tray. (When the paper size is changed, this
simulation must be executed to change the paper size in software.)
simulation must be executed to change the paper size in software.)
3
Set the specifications of the auditor. (Setting must be made according to the auditor
use conditions.)
use conditions.)
5
Set the count mode of the total counter and the maintenance counter.
6
Set the specifications (paper, fixed magnification ratio, etc.) of the destination.
10
Set the trial mode of the network scanner.
18
Set Disable/Enable of the toner save mode operation.
30
Set the operation mode corresponding to the CE mark.
32
Set the special functions.
35
Set the display mode of SIM 22-4 trouble history when a same trouble occurred
repeatedly. There are two display modes: display as one trouble and display as
several series of troubles.
repeatedly. There are two display modes: display as one trouble and display as
several series of troubles.
38
Set Continue/Stop of print when the maintenance life is reached.
50
Set functions.51Used to set the specifications of the serial port operation. (For PCI)
52
Set whether non-printed paper (insertion paper, cover paper) is counted up or not.
56
Set ON/OFF of the Life Correction.
65
Set the finisher alarm mode.
69
Set the operating conditions for toner near end.
73
Enlargement continuous shoot, A3 wide copy mode image loss (shade delete
quantity) adjustment
quantity) adjustment
74
Set the OSA trial mode.
78
Set the password of the remote operation panel.
79
Set YES/NO of the pop-up display of user data delete result.
27
1
Set non-detection of communication error (U7-00) with RIC.
2
Set the sender's registration number and the HOST server telephone number.
4
Set the initial call and toner order auto send.
5
Set the machine tag No. (This function allows the host computer to check the
machine tag No.) (FSS function)
machine tag No.) (FSS function)
6
Set of the manual service call.
7
Set of the enable, alert callout.
9
Set the paper transport time recording YES/NO threshold value and shading gain
adjustment retry number.
adjustment retry number.
10
Clear the trouble prediction history information.
11
Check the serial communication retry number and the scanner gain adjustment
retry number history.
retry number history.
Click on the first or last page to see other MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man5) service manuals if exist.