DOWNLOAD Sharp MX-M232D (serv.man3) Service Manual ↓ Size: 9.62 MB | Pages: 127 in PDF or view online for FREE

MX-M182 SIMULATIONS 7-57

66

31

The following bit 0/1 is alternatively switched. At the same time, the target signal name is highlighted.

32

Used to check receive data from the line and judge whether the following receive data and the judged data 
number accord together or not. If they accord, "OK" is notified. If not, "NG" is notified. Judgment is made 
from the receive start data and the data must be accorded continuously.

Main 
code

Sub 

code

Contents

Remark

Sim66-31 TEL OUTPUT

Sim66-31 TEL OUTPUT

After selection
with numeric keys

[OK] key

[OK] key

[BACK] key

Sim66-31 TEL OUTPUT

1:CION

 2:150VON

3:EC  

4:S

(1 - 5) 

X

1:CION 5:MSR

 EXEC

1:CION 5:MSR

PRESS BACK TO STOP
 

EXEC

Sim66-31 TEL OUTPUT

5:MSR

(1 - 5) 

X

Selection of two or more items can be made.
(The selected numbers are highlighted.)
Though numeric keys is pressed in the sequence
of "1 and 5" or "5 and 1," the display is made
in the sequence of the normal order
(1 and 5) when OK key is pressed.

After pressing [OK] key,
during execution

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
Numeric keys 

: Item selection

[OK] key 

: Input value settlement and execution

[START] key 

: Input value settlement and execution

[BACK] key 

: Returns to the selection window

         keys 

: Page switch

[C] key 

: Input value clear. ON when highlighted.

Sim66-32 RECV DATA

[OK] key

Sim66-32 RECV DATA

Sim66-32 RECV DATA

CHECK RECEIVE DATA

  

EXEC

RESULT XX

 

After pressing 
[OK] key,
during 
execution

RECEIVING

 

EXEC

Simulation code input window

"RECEIVING" is displayed 
only during receive. 

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
[OK] key 

: Settlement

[START] key 

: Settlement

[BACK] key  : Simulation code input window
[C] key 

: Disable

XX 

: "OK/NG" is displayed 

Completion of 
execution
(Highlighted 
 during execution)

[BACK] key

MX-M182 SIMULATIONS 7-58

66

33

Used to detect signals and display the result with ON/OFF.

34

Used to perform a send/receive test and measure and display the time required for send/receive of the 
image data in the communication.

37

Used to adjust the speaker sound volume.
During execution of this simulation, the following test sound is sent to the line and the speaker. 
The send level to the line is set to the soft SW setting value. 
The speaker sound volume can be adjusted by the operation.
The type of sound can be selected among the following:
1.Call sound, 2.Line monitor sound, 3.On-hook, 4.Terminating sound, 5.Communication end sound, 
6.DTMF send sound
For each type of sound, the sound volume can be selected among the following:
No sound, Small, Medium, Large
The set value is written into each soft  SW. 

Main 
code

Sub 

code

Contents

Remark

CI  :     FNET:

 EXEC

Sim66-33 SIGNAL CHK

CNG :     CED :
BT  :     DT  :

 EXEC

Sim66-33 SIGNAL CHK

1:CI FNET
2:CNG CED BT DT
3:Flag SDT DTMF
   (1 - 3) 

X

Sim66-33 SIGNAL CHK

Flag:     SDT :
DTMF:

 EXEC

[OK] key

[OK] key

[BACK] key

[OK] key

[BACK] key

[OK] key

[BACK] key

Sim66-33 SIGNAL CHK

CI  :OFF  FNET:OFF

DETECT 

EXEC

Sim66-33 SIGNAL CHK

CNG :OFF   CED :OFF
BT  :OFF 

DT  :OFF

DETECT 

EXEC

Sim66-33 SIGNAL CHK

Flag:OFF  SDT :OFF
DTMF:OFF

DETECT 

EXEC

Sim66-33 SIGNAL CHK

After selection with numeric key

After pressing [OK] key,
during execution

After pressing [OK] key,
during execution

After pressing [OK] key,
during execution

SIM66-33 initial window

SIM66-33 initial window

SIM66-33 initial window

1:CI FINET

2:CNG CED BT DT

3:Flag SDT DTMF

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
[C] key 

: Input clear

Numeric key 

: Item selection

[ON] key 

: Input value settlement and execution

[START] key 

: Similar to OK key

Signal detection
YES/NO is displayed
with ON/OFF.

Signal detection
YES/NO is displayed
with ON/OFF.

Signal detection
YES/NO is displayed
with ON/OFF.

Sim66-34 COMM. TIME

[OK] key

[BACK] key

Sim66-34 COMM. TIME

  

EXEC

COMM. TIME:
 xxx:xx:xx:xxxms

 

Simulation code
input window

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
[OK] key 

: Settlement

[BACK] key 

: Simulation code input window

[START] key 

: Settlement

[C] key 

: Disable

Immediately after 
pressing [OK] key, the 
window shifts to the 
next one.

Type of sound

Test sound

Sound volume setting value

0

1

2

3

1.Call sound

Call sound

No Sound

Small

Medium

Large

2.Line monitor sound

Communication signal 
sound (33600bps)

No Sound

Small

Medium

Large

3.On-hook

Communication signal 
sound (33600bps)

Setting 
disable

Small

Medium

Large

4.Terminating sound

Read end sound

No Sound

Small

Medium

Large

5.Communication end sound Communication end 

sound

No Sound

Small

Medium

Large

6.DTMF send sound

DTMF send sound

No Sound

Small

Medium

Large

MX-M182 SIMULATIONS 7-59

66

37

The following soft SW's are not affected
SW55-4 - 5 Send end sound
SW55-6 - 7 Receive end sound

38

Time setting/check
Used to write/read the time (year, month, day, o'clock, minute) into/from the RTC on the FAX PWB.

Main 
code

Sub 

code

Contents

Remark

Type of sound

Soft SW number

1. Sound volume of call sound

SW 53-3 - 4

Sound volume of call sound (Low)

SW131-5 - 8

Sound volume of call sound (Medium)

SW132-1 - 4

Sound volume of call sound (High)

SW132-5 - 8

2. Line monitor speaker sound volume

SW 52-5 - 6

Line monitor speaker sound volume (Low)

SW127-1 - 4

Line monitor speaker sound volume (Medium)

SW127-5 - 8

Line monitor speaker sound volume (High)

SW128-1 - 4

3. On-hook speaker sound volume

SW 53-1 - 2

On-hook speaker sound volume (Low)

SW130-1 - 4

On-hook speaker sound volume (Medium)

SW130-5 - 8

On-hook speaker sound volume (High)

SW131-1 - 4

4. Scan end speaker sound volume

SW 52-1 - 2

Scan end speaker sound volume (Low)

SW124-1 - 4

Scan end speaker sound volume (Medium)

SW124-5 - 8

Scan end speaker sound volume (High)

SW125-1 - 4

5. Communication end speaker sound volume

SW 52-7 - 8

Communication end speaker sound volume (Low)

SW128-5 - 8

Communication end speaker sound volume (Medium)

SW129-1 - 4

Communication end speaker sound volume (High)

SW129-5 - 8

6. DTMF send speaker sound volume

SW 52-3 - 4

DTMF send speaker sound volume (Low)

SW125-5 - 8

DTMF send speaker sound volume (Medium)

SW126-1 - 4

DTMF send speaker sound volume (High)

SW126-5 - 8

[OK] key

After selection 
with numeric keys

[BACK] key

[OK] key

After selection 
with numeric keys

XX: The current set 
value is displayed.

YY: Input in the 
range of 1(Low) - 
15 (High) .

A sound beeps at the 
set sound volume. 
While the speaker is 
sounding, [EXEC] is 
highlighted.
Press [BACK] key to 
stop the sound. 

[OK] key

Sim66-37 SPEAKER

1:RINGER
2:LINE MONITOR
3:ON HOOK
( 1 - 6 ) 

X

Window display
1

ȇRINGER

2

ȇLINE MONITOR

3

ȇON HOOK

4

ȇSCAN FINISH

5

ȇTX/RX FINISH

6

ȇDTMF

Sim66-37 SPEAKER

ON HOOK
1:SMA.2:MED.3:LAR.

( 1 - 3 ) 

X

Sim66-37 SPEAKER

ON HOOK
SMALL -
 XX
( 1 - 15 ) 

YY

Sim66-37 SPEAKER

ON HOOK
SMALL -
 XX
( 1 - 15 ) 

YY

Sim66-37 SPEAKER

ON HOOK
SMALL -
PRESS BACK TO STOP
 

EXEC

Press [BACK] key to 
stop the sound.

After inputting 
with numeric key

While [EXEC] is 
highlighted, a 
sound beeps. 

Sim66-38 DATE & TIME

Sim66-38 DATE & TIME

Sim66-38 DATE & TIME

Sim66-38 DATE & TIME

DATE
MONTH XX

(1-12) YY

DATE
DAY XX

(1-31) YY

YEAR 20YY
MONTH YY
DAY YY
 EXEC

After inputting 
with numeric 
key, press 
[OK] key.

[OK] key

[OK] key

After inputting 
with numeric 
key, press 
[OK] key.

[OK] key

After inputting 
with numeric 
key.

[OK] key

After inputting 
with numeric 
key.

[OK] key

Sim66-38 DATE & TIME

TIME XX:XX

(00-59) YY

xx: The current year/month/day 
      is displayed.
yy: The input value is displayed. 

xx: The current time is displayed.
yy: The input value is displayed.

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
Numeric keys 

: Item selection and time input

[OK] key 

: Settlement

[START] key : Settlement
[BACK] key  : Returns to the previous window or
 

  the simulation code input window. 

[C] key 

: Input value clear

After execution, the 
display shifts to the sub 
code input window. 

DATE
YEAR XXXX

(2011-2062) YY

MX-M182 SIMULATIONS 7-60

66

42

Used to write the program again into the power control which is installed to the FAX BOX.

43

Used to write the adjustment value of the program into the power control which is installed to the FAX BOX.

Default:
1: 6



2: 10



3: 142



4: 3



5: 15



6: 240



7: 2



8: 20

52

• The pseudo ringer sound is delivered both from the machine (speaker).

• This operation is continued until the interruption command is made by pressing RETURN key.

• The LCD displays the TEL/LIU status and the HOOK status.
• While the pseudo ringer is delivered, the RBT )ring back tone) is delivered to the line. The bell is ON for 

1sec and OFF for 2sec. 

67

50

Used to set an limitation on the print data reception speed when the USB transfer speed is at full speed.

* When images are disturbed in printing through USB, change the setting and try again.
[CA] key: Exits from the simulation mode. 
[INTERRUPT] key: Shifts to the sub code entry window. 

Default:
3

Main 
code

Sub 

code

Contents

Remark

[OK] key

[BACK] key

Sim66-42 PIC RELOAD

Sim66-42 PIC RELOAD

ARE YOU SURE?

  

EXEC

Sim66-42 PIC RELOAD

OK

  

EXEC

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
[OK] key 

: Settlement

[BACK] key 

: Returns to the simulation 

 

  code input window.

ARE YOU SURE?

 

EXEC

Sub code input window

During execution, [EXEC] is 
highlighted. 

Incase of writing 
error, "NG" is 
displayed. 

After pressing 
[OK] key, during 
execution

Window display

Setting 

range

1:CI_LEVEL_JUDGE

2 - 15

2:CI_CYCLE_MIN

1 - 254

3:CI_CYCLE_MAX

2 - 255

4:CI_COUNT

2 - 15

5:RES_3.3V_LEVEL_JUDGE

2 - 15

6:EXHS_LEVEL_JUDGE

2 - 255

Window display

Setting 

range

7:RHS_LEVEL_JUDGE

2 - 15

8:SON_TIMEOUT

1 - 127

9:WRITE

-

Window display

Setting 

range

[OK] key

[OK] key

After inputting 
with numeric 
key

9. When 
WRITE is 
selected

SIM66-43 initial window

XX: The current set value is displayed.
YY: Input value

Sim66-43 PIC ADJUST

1:CI LEVEL
2:CI CYCLE MIN
3:CI CYCLE MAX
( 1 - 9 ) 

X

Sim66-43 PIC ADJUST

CI LEVEL
 XX

( 2 - 15 ) 

YY

[OK] key

After inputting 
with numeric 
key

Sim66-43 PIC ADJUST

OK

  

EXEC

After execution, the display shifts
to the sub code input window. 

Sim66-43 PIC ADJUST

ARE YOU SURE?

 

EXEC

During execution, [EXEC] is 
highlighted. 

Incase of writing 
error, "NG" is 
displayed. 

[BACK] key

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
[OK] key 

: Settlement

[BACK] key 

: Returns to the simulation 

 

  code input window.

Sim66-52 PSEUDO RNG

Sim66-52 PSEUDO RNG

PSEUDO RINGER CHK

  

EXEC

Sim66-52 PSEUDO RNG

PSEUDO RINGER CHK

  

EXEC

After pressing 
[OK] key, during 
execution

PSEUDO RINGER CHK
PRESS BACK TO STOP

 

EXEC

[CA] key 

: Simulation cancel

[INTERRUPT] key : Sub code input window
[OK] key 

: Execution

[BACK] key 

: Returns to the selection window.

[START] key 

: Execution

[C] key 

: Disable

[BACK] key

[OK] key

Sim67-50  USB SPEED

1:FULL SPEED

2

2

Display : 

Setting

1 : 

FAST

2 

: NORMAL 1

3 

: NORMAL 2

4 : 

SAFE

[      1-   4]

Slow

Fast