Sharp MX-M1055 / MX-M1205 (serv.man6) Handy Guide ▷ View online
SHARP
INITIAL SETUP
17
PRINT ENGINE IMAGE SKEW:
Sim 64-02
Image Writing Adjustment:-
Select A=1, B=1, C=254, D=255, E=1, F=1, G=8.
PRINT IMAGE POSITION & BK MAGNIFICATION:
Check Print Image Off Centre & Lead Edge position - Use Sim 50-10:-
Inside dimension of the printed halftone must be 240±0.5mm.
Lead edge void area 3.0 ± 1.0mm.
Rear edge void area 2.0mm - 5.0mm.
Front & Rear Void areas 2.0 ± 2.0mm.
Lead edge void area 3.0 ± 1.0mm.
Rear edge void area 2.0mm - 5.0mm.
Front & Rear Void areas 2.0 ± 2.0mm.
If NG, perform the following adjustments as required:-
Manual Adjustment:
Sim 50-10
BK MAG / Image Off Centre Adjustment (All Trays).
Sim 50-05
Printer Lead Edge & Void Adjust.
Automatic Adjustment:
Sim 50-28
BK MAG ADJ (Main Scan Mag).
SETUP/PRINT ADJ (Lead, Offset or All).
ENGINE & PRINTER HALF TONE ADJUSTMENT:
Sim 46-74
Engine & Printer Half Tone Calibration:
Select FACTORY Mode.
IMAGE QUALITY CHECK [COPY & PRINT]
Check Image Quality (Copy Mode) – Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:-
Sim 46-02
Copy Density Adjust. (B/W).
Sim 46-09
SPF Copy Density Adjust.
Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc):
Sim 48-01
Magnification Adjustment (OC & SPF).
Sim 50-01
Lead/Rear Edge, Loss & Void Adjust.
Sim 50-12
OC & SPF Off Centre Adjust.
Check SPF Skew adjustment.
Automatic Adjustment:
Sim 50-28
OC ADJUST (Lead, Offset & Mag).
SPF ADJ:(Lead, Offset & Sub scan).
Check Print Image Quality:
Sim 64-05
PCL Density Test Page.
Sim 64-06
PS Density Test Page.
INITIAL SETUP
SHARP
18
PERIPHERAL / OPTION CONFIGURATION
MULTI BYPASS TRAY – MX-MFX1:
Sim 40-02
Bypass Tray Adjustment [MX-MFX1 only].
FACSIMILE OPTION – MX-FX11 [for MX-M904/1054/1204 only]:
Sim 66-02
Fax SW Setting (Destination).
Sim 66-10
Image Data Memory Clear.
Sim 66-39
Fax Destination Set
FINISHER OPTION – MX-FN21/22/24/25:
Sim 03-10
Saddle Fold/Staple Position Adjustment [MX-FN22/25 only].
Sim 26-65
Finisher Alarm Mode:-
Limit number of Copies in staple mode (ON/OFF).
Limit the number of sets loaded in the saddle staple (ON/OFF).
**Limit load of folded paper on paper exit and limit load on 50-sheet
Staple saddle finisher are set in SADDLE COPIES.
FOLDING UNIT – MX-FD10:
Z Fold Skew Adjustment check
EXTERNAL ACCOUNTING MODULE – MX-AMX3:
Sim 55-03
Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03
Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06
Data Simulation Print
Device Clone & Storage Backup
Sim 56-01
Backup EEPROM Data to HDD
SHARP
DENSITY & GRADATION ADJUSTMENT
19
Automatic Grey Balance Adjustment – FACTORY MODE:
Note:
When adjusting colour balance before or after routine maintenance, always use the recommended paper
(Mondi 90gsm or equivalent) for optimum image quality.
When adjusting colour balance before or after routine maintenance, always use the recommended paper
(Mondi 90gsm or equivalent) for optimum image quality.
HIGH DENSITY PROCESS CONTROL:
Sim 44-06 Execute High Density Process Control
HALF TONE PROCESS CONTROL:
Sim 44-26 Execute Half Tone Process Control
GREY BALANCE ADJUSTMENT:
Sim 46-74 Half tone grey balance adjustment for COPY & PRINTER – select FACTORY.
PRINTER DENSITY CHECK:
Sim 64-05 Printer Self-Print Test (PCL)
Sim 64-06 Printer Self-Print Test (PS)
Manual Grey Balance Adjustment – SERVICE MODE:
HIGH DENSITY PROCESS CONTROL:
Sim 44-06 Execute High Density Process Control
HALF TONE PROCESS CONTROL:
Sim 44-26 Execute Half Tone Process Control
GREY BALANCE ADJUSTMENT:
Sim 46-74 Half tone grey balance adjustment for COPY & PRINTER – select SERVICE.
MANUAL GREY BALANCE ADJUSTMENT:
Sim 46-21 Engine
Sim 67-25 Printer
PRINTER DENSITY CHECK:
Sim 64-05 Printer Self-Print Test (PCL)
Sim 64-06 Printer Self-Print Test (PS)
SERVICE TARGET SETTING [REGISTER]:
Sim 63-07 Engine
Sim 67-27 Printer
Return to Default Setting – SERVICE MODE:
STANDARD SERVICE TARGET SETTING:
Sim 63-08 Reset Standard Service Target for COPY.
Sim 67-28 Reset Standard Service Target for PRINTER.
Sim 46-74 Half tone grey balance adjustment for COPY & PRINTER – select SERVICE.
MAINTENANCE
SHARP
20
Maintenance Indications:
TA
Maintenance [All] Counter has reached specified limit
DK
Black Drum Counter has reached the specified life.
Replace OPC Drum
Process
Section
VK
Black Developer Counter has reached the specified life.
Replace Black Developer
Process
Section
FK3
Fuser Web Cleaner (Counter) has reached the specified
limit - (Pop Up FK3 Error – Web End Detected)
Replace the
Web Cleaning Kit
Fuser
Section
Consumable Quick Reference Guide:-
Total Maintenance
500K
1000K
1500K
2000K
2500K
Process
Drum
MX-850GR
x
x
x
Developer
MX-900GV
x
x
x
Developer Maintenance Kit
MX-900DK
x
x
x
Main Charge Kit
MX-900MK
Cleaning Blade Kit
MX-900CB
Paper Dust Removal Kit
MX-900PD
Filter Kit
MX-900FL
Waste Toner Collector
MX-850HB
Fuser
Fuser Maintenance Kit
MX-950KC
Heat Roller Kit
MX-950HK
x
x
x
Web Cleaning Kit
MX-950WC
Transfer
Transfer Belt Kit
MX-900TT
x
x
x
Starting Powder:
The following starting powder should be applied to the relevant consumable item during maintenance:
Starting Powder
OPC Drum
Transfer Belt
MX-M904
MX-M1054/1204
MX-M1055/1205
MX-M1055/1205
CKOG-0345DS51
[Yellow Toner]
UKOG-0312FCZZ
[Stearic Acid]
Note: The Yellow Toner used for Start Powder (OPC Drum only) is the same as MX-31GTYA
.
Click on the first or last page to see other MX-M1055 / MX-M1205 (serv.man6) service manuals if exist.