DOWNLOAD Sharp MX-LC13 (serv.man27) Service Manual ↓ Size: 11.35 MB | Pages: 68 in PDF or view online for FREE

Model
MX-LC13 (serv.man27)
Pages
68
Size
11.35 MB
Type
PDF
Document
Service Manual / Technical Bulletin
Brand
Device
Copying Equipment / IMPROVEMENTS FOR INSTALLING MX-LC13 N
File
mx-lc13-sm27.pdf
Date

Sharp MX-LC13 (serv.man27) Service Manual / Technical Bulletin ▷ View online

MX-M1204  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 15
b. Mechanical Adjustment2
1) Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray. 
When shifting the line of printing from the center of the paper in
the direction A of arrow as shown below:
2) Loosen the blue screws of the rear regulation plate, and move
the plate with referring the carved marks by the dimension
shifted in the direction A (R side), and tighten the blue screws.
3) Set a sheet of paper on the paper feed base tray and loosen
the blue screws of the front regulation plate.
Move the front regulation plate to the direction A (R side) with
pushing paper to the front regulation plate.
4)
Set the front regulation plate to make gap between the rear
sideplate and paper and tighten the blue screws of the fron
regulation plate.
NOTE: Avoid bending paper with too much closing the regula-
tion plates.
NOTE: When shifting the line of printing from the center of the
paper to rear side, move the front regulation plate to
adjust.
G. Off-center adjustment (Simulation)
(1) Off-center check
1)
Run Sim50-10 using the keypad on the main unit.
2)
This screen allows you to configure the print off-center adjust-
ment value for each paper feed tray.
3)
On the touch panel, press DOWN key to select "H: 50:
MAINLCT1."
4)
Enter the desired adjustment value through the numeric key-
pad. (This value, which defaults to 50, can be adjusted within
the range of 1 to 99)
-  Reducing the adjustment value by 1 causes the main scan/
print position to shift by 0.1mm toward the rear.
-  Increasing the adjustment value by 1 causes the main scan/
print position to shift by 0.1mm toward the front.
5)
After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting.
6)
Check that the adjustment pattern image is printed in the cor-
rect position.
Measure the dimensions of the void areas on the front and rear
frame sides of the adjustment pattern image, and make sure
that the following conditions are met:
If the above condition is not met, do the following:
7)
Change the adjustment value. (Enter the adjustment value and
press the [OK] key.)
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm. 
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied. 
8)
After you have completed the adjustment, exit from Simulation
mode by pressing the [CA] key.
MEMO:For details of the adjustment and checking proce-
dures, refer to the "[5] ADJUSTMENTS AND SETTINGS" on
the Service Manual.
If the center is shifted, however, adjust with the simulation. If the
shift is not recovered, perform [F. Mechanical Adjustment] again.
5HDU
%OXH6FUHZV
5HJXODWLRQ3ODWH
)URQW
3DSHU
3XVKSDSHUWRWKHIURQW
VLGHSODWH
MM
3DSHU
$
%
3ULQWHGVXUIDFH
3DSHUGHOLYHU\
GLUHFWLRQ
,IWKHGLPHQVLRQRI%LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVUHDUGLUHFWLRQ
,IWKHGLPHQVLRQRI$LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVIURQWGLUHFWLRQ
5HDU6LGH
)URQW6LGH
$%
PP0HFKDQLFDODGMXVWPHQWPP0HFKDQLFDODGMXVWPHQW
MX-M1204  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 16
H. Diagonal feed adjustment
(1) Diagonal Adjustment
1) Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray. 
2) Adjust the diagonal feed.
3) Set a sheet of paper on the paper feed base tray and adjust
the width of the regulation plate.
In the case of diagonal feed 1
Loosen the 2 blue screw (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the clockwize direction and fix the blue screw.
Loosen the 2 blue screws (2) on the rear regulation plate.
To make parallel with the front regulation plate, move the rear
regulation plate in the clockwize direction and fix the screws.
In the case of diagonal feed 2
Loosen the 2 blue screws (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the counterclockwize direction and fix the blue screw.
Loosen the 2 blue screws (2) on the rear regulation plate.
To make parallel with the front regulation plate, move the rear
regulation plate in the counterclockwize direction and fix the
screws.
NOTE: When fixing the rear regulation plate, not to fix it more
closely against the paper.
(The target of the gap between the edge of paper and the
rear regulation plate is about 1.0mm)
NOTE: After completion of the adjustment, check that the front reg-
ulation plate and the rear regulation plate are in parallel to
each other.
I. Height Adjustment
If there’s some gap between cabinets or door adjustment is neces-
sary, adjust the height adjustment.
1)
Install the adjuster (Packed items No.3) and adjuste the height
of LC13 (4 places)
Diagonal feed 1
Diagonal feed 2
Transport 
direction
)URQW
3DSHU
5HDU
5HJXODWLRQ3ODWH
)URQW
3DSHU
5HDU
5HJXODWLRQ3ODWH
TopPage
4
: ‘14/Jan
4
MX-M1204  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 17
2) Adjust the clearance of the exterior cabinet evenly. 
See drawing below.
Front side
Rear side
3)
Adjust the height of the exterior cabinet to the same level.
Front side
Rear side
MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 1
MX-7040N
Service Manual
 
[8] MX-LC13 (LARGE CAPACITY TRAYS)
1.  Unpacking
NOTE: Before installing MX-LC13, the installation of MX-RB14 is
needed.
A. Remove the large capacity trays
1) Remove the machine from the palette with a forklift or a slope
(DKIT-0367FCZZ).
NOTE: When using a forklift, raise the casters to the top in
order not to break them.
B. Packed items check
*1: Not used for the after July / 2013 production.
*2: Not packed after July / 2013 production
*3: Only 4 pcs of screws are used for after July / 2013 production.
*4: Packed number was changed after July / 2013 production.
2.  Unit production month check
A. Unit production month check
Check the label on the carton box as the figure below.
Before June 2013 production: 
120V series: Less than A35 
200V series: Less than A25
After July 2013 production: 
120V series: More than A46
200V series: More than A36
B. Combination for Installation
The installation procedure is different by the combination of the
production month of MX-RB14 and MX-LC13.
C. Differences list by combination
4
3
2
5
1
6
7
11
12
8
10
9
No.
Name
Quantity
1
LCT connecting plate F
1
2
LCT connecting plate R
1
3
Height adjustment plate
4
4
Screw (S-tight, M4 x 8)
*3
11 to 8 *4
5
Power cable
1
6
Connecting plate upper
2
7
Positioning plate F
*2
1
8
Positioning plate R
*2
1
9
Connecting plate lower F
*1
1
10
Connecting plate lower R
*1
1
11
Screw (Hex washer S-tight M4 x 18)
4
12
L-shape driver 
1
Combination of RB14 / LC13
Instlattion method
Less than A10 / Less than A35 or A25
Go to [3. Installation 1]
Less tahn A10 / More than A46 or A36
Go to [4. Installation 2]
More than A20 / Less than A35 or A25
Go to [5. Installation 3]
More than A20 / Less thanA46 or A36
Go to [6. Installation 4]
Combination of RB14 / LC13
Positioning Pin
Connection plate
Off center adjustment
RB14 height adjustment
Less than A10 / 
Less than A35 or A25
Use
Use
1. By height adjustment
2. By regulation plates adjustment
Use the adjuster for height 
adjustment.
Less tahn A10 / 
More than A46 or A36
Not use 
Use
1. By connection plate adjustment 
2. By regulation plates adjustment
Use the adjuster for height 
adjustment.
More than A20 / 
Less than A35 or A25
Use
Not used (Already 
attached on RB14)
1. By height adjustment
2. By regulation plates adjustment
No need to adjust the height. 
(lifted by LC13)
More than A20 / 
Less thanA46 or A36
Not use 
Not used (Already 
attached on RB14)
1. By connection plate adjustment 
2. By regulation plates adjustment
No need to adjust the height. 
(lifted by LC13)
TopPage
5
: ‘14/Jan
5
Page of 68
Display

Click on the first or last page to see other MX-LC13 (serv.man27) service manuals if exist.