DOWNLOAD Sharp MX-LC13 (serv.man15) Service Manual ↓ Size: 11.35 MB | Pages: 68 in PDF or view online for FREE

MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 6

NOTE: Avoid bending paper with too much closing the regulation

plates.

NOTE: When shifting the line of printing from the center of the

paper to rear side, move the front regulation plate to adjust
it.

1) Run Sim50-10 using the keypad on the main unit.
2) This screen allows you to configure the print off-center adjust-

ment value for each paper feed tray.

3) On the touch panel, press [DOWN] Key to select "H: 50:

MAINLCT1."

4) Enter the desired adjustment value through the numeric key-

pad. (This value, which defaults to 50, can be adjusted within
the range of 1 to 99)

-    Reducing the adjustment value by 1 causes the main scan/

print position to shift by 0.1mm toward the rear.

-    Increasing the adjustment value by 1 causes the main scan/

print position to shift by 0.1mm toward the front.

5) After entering the adjustment value, press the [EXECUTE] key

on the touch panel to start printing and save the setting.

6) Check that the adjustment pattern image is printed in the cor-

rect position.
Measure the dimensions of the void areas on the front and rear
frame sides of the adjustment pattern image, and make sure
that the following conditions are met:

No adjustment is needed if A-B=+/-3.0 mm.
If the above condition is not met, do the following:

7) Change the adjustment value. (Enter the adjustment value and

press the [OK] key.)
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm. 
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied. 

8) After you have completed the adjustment, exit from Simulation

mode by pressing the [CA] key.
MEMO：For details of the adjustment and checking proce-
dures, refer to the "[5] ADJUSTMENTS AND SETTINGS" on
the Service Manual.

1)

Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray. 

2)

Adjust the diagonal feed.

3)

Set a sheet of paper on the paper feed base tray and adjust
the width of the regulation plate.
In the case of diagonal feed 1
Loosen the 2 blue screw (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the clockwize direction and fix the blue screw.

Loosen the 2 blue screws (2) on the rear regulation plate.
To make parallel with the front regulation plate, move the rear
regulation plate in the clockwize direction and fix the screws.

MM

3DSHU

!

"

3ULQWHGVXUIDFH

3DSHUGHOLYHU\
GLUHFWLRQ

$% PP

5HDU6LGH

)URQW6LGH

$%
PP0HFKDQLFDODGMXVWPHQWPP
0HFKDQLFDODGMXVWPHQW

Diagonal feed 1

Diagonal feed 2

Transport 
direction

)URQW

3DSHU

5HDU

5HJXODWLRQ3ODWH

TopPage

: ‘14/Jan

MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 7

In the case of diagonal feed 2
Loosen the 2 blue screws (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the counterclockwize direction and fix the blue screw.

Loosen the 2 blue screws (2) on the rear regulation plate.
To make parallel with the front regulation plate, move the rear
regulation plate in the counterclockwize direction and fix the
screws.

NOTE: When fixing the rear regulation plate, not to fix it more

closely against the paper.
(The target of the gap between the edge of paper and the
rear regulation plate is about 1.0mm)

NOTE: After completion of the adjustment, check that the front reg-

ulation plate and the rear regulation plate are in parallel to
each other.

NOTE: When installing this machine in a place of low atmospheric

pressure, check and conform to the adjustment contents in
the MX-LC13 Service Manual.

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Draw out the second tray from the unit.
Push the button of the bottom side of the unit to unlock the
tray, and then slowly pull out the tray until it stops.

2)

Remove 3 screws from the tray.

3)

Slowly insert the tray to the original position.

)URQW

3DSHU

5HDU

5HJXODWLRQ3ODWH

TopPage

: ‘14/Jan

MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 8

1) Attach the LCT connecting plate to the large capacity trays

with the screws (Packed items No.4 S-tight, M4 x 8).
MEMO: The reference label is attached to the plate. Attach it
so that the label can be seen from the outside.

2) Attach the height adjustment mounting plates F/R and the con-

nection plates lower F/R to the relay unit.

3) Fix the upper mounting plates to the machine with the screws

(Packed items No. 4 S-tight, M4 x 8).

4)

Insert the installation plate of the LCT to the mounting plate of
the paper pass unit.

When separating, tighten the screw to release the lock. 
When connecting again, loosen the screw after connection.

1)

Remove the cover of LCT.

MX-7040N  MX-LC13 (LARGE CAPACITY TRAYS)  8 – 9

2) Cut the rear cabinet with using nipper or cutter to make a hole,

and then wire the harness through the hole.

3) Connect the harness inside the large capacity trays, tighten

the screw (RB14 Packed items No.13),  and pass the harness
through the clamp.

4) Fix the cover with the screw.

5)

Connect the connector from LCT to the paper pass unit and
tighten the screw.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

1)

Check to insure that the main body is standby state, and press
the [System setting] key on the operation panel.

2)

Menu screen is displayed on the touch panel. Select the
[Paper Tray Settings].

3)

Select the paper size of large capacity tray from contents of
[Paper Tray Settings].

1)

Run Sim50-10 using the keypad on the main unit.

2)

Press [EXECUTE] key to print out for each paper feed tray.

3)

Check the void area of the adjustment pattern and check the
“Off-center” shift amount (A-B).
“A-B” is over 3mm: Move to Mechanical Adjustment 1
“A-B” is less than +/-3mm: Move to Mechanical Adjustment 2

!

"

3ULQWHGVXUIDFH

3DSHUGHOLYHU\
GLUHFWLRQ

,IWKHGLPHQVLRQRI%LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVUHDUGLUHFWLRQ

,IWKHGLPHQVLRQRI$LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVIURQWGLUHFWLRQ

5HDU6LGH

)URQW6LGH

$%
PP0HFKDQLFDODGMXVWPHQWPP0HFKDQLFDODGMXVWPHQW