Sharp MX-FNX5 Service Manual ▷ View online
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 6
G. STAPLE TRIMMINGS HOPPER FULL SENSOR
• Open the front door
• Pull out the stapler unit
• Remove the rear cover ( x 2).
Remove:
[A] Staple trimmings hopper
[B] Hopper holder (
• Pull out the stapler unit
• Remove the rear cover ( x 2).
Remove:
[A] Staple trimmings hopper
[B] Hopper holder (
x1, Hook x1,
x1)
[C] Hopper full sensor (
x 1)
[D] Hopper set sensor (
x 1)
H. STAPLER ROTATION HP AND STAPLER
RETURN SENSORS
1)
Remove the stapler unit. (See next page.)
2)
Remove the stapler mount bracket [A] ( x 4) (Springs x 2).
3)
Replace the stapler rotation HP sensor [B] (
x 1).
4)
Replace the stapler return sensor [C] (
x 1).
[F]
[G]
[H]
[A]
[B]
[C]
[D]
[A]
[C]
[B]
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 7
5. STAPLER
1)
Open the front door and pull out the staple tray.
2)
Remove the stapler unit harness cover [A] ( x 2).
3)
Lift the stapler [B] off of its pegs (
x 2)
4)
Remove plate [C] ( x 2).
5)
Attach this plate to the new stapler with the same screws
( x 2).
( x 2).
6)
Replace the frame guard [D] with the one provided with the
new stapler.
new stapler.
6. SHIFT TRAY
A. SHIFT TRAY EXIT, SHIFT TRAY LIFT MOTOR
(1) Shift Tray Exit Motor
• Rear cover (
1. COVERS -D.)
[A] Shift tray exit motor bracket
( x2,
( x2,
x1,
X1, Timing belt x1)
[B] Shift tray exit motor ( x2)
(2) Shift Tray Lift Motor
• Rear cover (
1. COVERS -D.)
[A] Gear cover ( x2)
[A]
[B]
[C]
[D]
(1)
Shift Tray Exit Motor
(2)
Shift Tray Lift Motor
(1)
(2)
[B]
[A]
[A]
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 8
[B] Shift tray lift motor bracket ( x2)
[C] Shift tray lift motor ( x2,
[C] Shift tray lift motor ( x2,
x1, Timing belt x1)
B. DRAG ROLLER/DRAG DRIVE MOTORS, DRAG
DRIVE HP SENSOR
Remove:
• Front door and all covers, except the left lower cover, top cover
• Front door and all covers, except the left lower cover, top cover
(
1. COVERS)
NOTE:
Be sure to lower the shift tray by pulling the gear toward you. The
shift tray must be down.
Be sure to lower the shift tray by pulling the gear toward you. The
shift tray must be down.
1)
Remove the left stay [A] ( x 2)
2)
Remove the shift tray mounting plate [B] ( x 2).
3)
Remove the end fence [A] and plate ( x8,
x6,
x2).
4)
Remove cover [B] ( x 4).
5)
Remove the motor stay [C] ( x4,
x7,
x4).
NOTE:
Make sure the motor and sensor connectors are disconnected
before removing.
Make sure the motor and sensor connectors are disconnected
before removing.
6)
Remove the drag roller motor unit [A]
(Bearing x1, x2,
(Bearing x1, x2,
x1)
7)
Remove the drag roller motor ( x2)
8)
Remove the drag roller HP sensor unit [B] ( x1)
9)
Remove the drag roller HP sensor (
x1, Pawls x3)
10) Remove the paper height sensor - shift/Z-fold unit [C]
( x2,
x2)
11) Remove the paper height sensor shift/Z-fold
(
x1, Pawls x3)
12) Remove the drag drive motor unit (
x4,
x2)
13) Remove the drag drive motor (
x2)
[B]
[C]
[A]
[B]
[A]
[B]
[C]
[A]
[B]
[C]
[D]
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 9
C. SHIFT MOTOR AND SENSORS
1)
Remove the end fence (
6. SHIFT TRAY -B.)
2)
Remove the shift motor bracket [A] (with motor)
( x 4,
( x 4,
x1,
x1)
3)
Remove the shift motor ( x4)
4)
Remove the half-turn sensor bracket [B] ( x 1)
5)
Remove half-turn sensor 1 [C] (
x1, Pawls x3)
6)
Remove half-turn sensor 2 [D] (
x1, Pawls x3)
D. JOGGER TOP FENCE MOTOR
1)
Open the front door and pull out the stapler tray unit.
(
(
1. COVERS -F.)
2)
Remove the jogger unit cover ( x2)
3)
Remove the motor bracket [A] ( x2, timing belt x1)
4)
Remove the jogger top fence motor [B] ( x2
x1
x1)
E. JOGGER UNIT
1)
Open the front door and pull out the stapler tray unit.
2)
Remove the jogger unit cover ( x2)
3)
Remove the jogger unit [A] ( x4,
x5,
x5)
F. JOGGER BOTTOM FENCE MOTOR
1)
Open the front door and pull out the stapler tray unit.
2)
Remove the jogger bottom fence motor unit [A]
( x3, timing belt x1,
( x3, timing belt x1,
x1,
x1).
[A]
[C]
[D]
[B]
[A]
[B]
[A]
[A]
Click on the first or last page to see other MX-FNX5 service manuals if exist.