Sharp MX-FN19 / MX-FN20 / MX-PN12 Service Manual / Specification ▷ View online
MX-FN19 MAINTENANCE 4 – 52
f. Removal of left upper cover
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
right, and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
g. Removal of grate-shaped upper guide
1) Move the tray [1] lower than the grate-shaped upper guide [2].
1) Move the tray [1] lower than the grate-shaped upper guide [2].
(For moving the tray, refer to "Removal of No. 1 tray")
2) Remove the five screws [3], and remove the grate-shaped
upper guide [2].
h. Removal of No. 1 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the metal plate [2] and the
slide guide [3]. If the grate-shaped upper guide has been
removed, there is no need to perform this procedure.
slide guide [3]. If the grate-shaped upper guide has been
removed, there is no need to perform this procedure.
2)
Remove the screw [4], and remove the stopper [5].
[3]
[2]
[1]
[4]
[3]
[2]
[1]
[2]
[1]
[1]
[3]
[2]
[5]
[4]
MX-FN19 MAINTENANCE 4 – 53
3) Remove the two screws [6], and open the harness holder [7] at
three positions, and disconnect the connector [8] at two posi-
tions.
tions.
4) Insert your finger into the hole in the back of the No. 1 tray [9].
Push the tray lift motor gear [10] toward you to release the
clutch, and lift the No. 1 tray [9].
clutch, and lift the No. 1 tray [9].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch,
therefore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
therefore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
i. Removal of No. 2 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the stopper [2].
2)
Remove the two screws [3], and disconnect the connector [4].
3)
Insert your finger into the hole in the back of the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch,
therefore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
therefore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
[7]
[8]
[6]
[6]
[9]
[10]
[2]
[1]
[2]
[1]
[4]
[3]
[3]
[5]
[6]
MX-FN19 MAINTENANCE 4 – 54
j. Removal of front inside lower cover
(FN19)
1) Remove the screw [1], and remove the leg cover [2].
(FN19)
1) Remove the screw [1], and remove the leg cover [2].
2) Remove the three screws [3], and shift the front inside lower
cover [4] to the left side, and remove it.
(FN20)
1) Remove the screw [1], and remove the roller knob [2].
2) Remove the four screws [3], and remove the front inside lower
1) Remove the screw [1], and remove the roller knob [2].
2) Remove the four screws [3], and remove the front inside lower
cover [4].
k. Removal of delivery upper guide
1)
1)
Remove the two screws [1] and the earth wire [2], and remove
the delivery upper guide [3].
the delivery upper guide [3].
l. Removal of paper folding roller
1)
1)
Disconnect the connectors [1] at two positions, and remove the
harness from the edge saddle [2] and the clamp [3].
harness from the edge saddle [2] and the clamp [3].
2)
Disconnect the connectors [4] at two positions, and remove the
harness from the edge saddle [5] at four positions.
harness from the edge saddle [5] at four positions.
3)
Remove the three screws [6], and take out the paper folding/
paper pushing motor base [7].
paper pushing motor base [7].
[3]
[2]
[3]
[1]
[4]
[1]
[2]
[1]
[3]
[1]
[3]
[2]
[5]
[4]
[6]
[4]
[5]
[7]
MX-FN19 MAINTENANCE 4 – 55
4) Disengage the hooks on the upper sides of the tension spring
front [8] and the tension spring rear [9].
5) Remove the two C-rings [10] at the back, and remove the sen-
sor flag [11] and the two bearings [12].
6) Remove the two C-rings [13] on the front side, and remove the
two gears [14].
7)
Remove the two bearings [15].
8)
Open the saddle delivery tray [16].
9)
Remove the two screws [17], and remove the two alignment
plates [18].
plates [18].
10) Shift the two paper folding rollers [19] to the front side, and
remove it in the delivery direction.
CAUTION: When installing, install the gear [2] so that the paper
folding roller groove [1] faces in the proper phase.
[8]
[9]
[12]
[10]
[11]
[14]
[13]
[15]
[16]
[18]
[17]
[17]
[19]
[1]
[2]
Click on the first or last page to see other MX-FN19 / MX-FN20 / MX-PN12 service manuals if exist.