Sharp MX-FN18 Service Manual ▷ View online
MX-FN18 MAINTENANCE 4 – 16
f. Removal of grate-shaped upper guide
1)
1)
Move down the tray [1] lower than the grate-shaped upper
guide [2]. (For moving of the tray, refer to "Removal of No. 1
tray")
guide [2]. (For moving of the tray, refer to "Removal of No. 1
tray")
2)
Remove the five screws [3], and remove the grate-shaped
upper guide [2].
upper guide [2].
g. Removal of No. 1 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the metal plate [2] and the
slide guide [3]. If the grate-shaped upper guide has been
removed, this procedure is unnecessary.
slide guide [3]. If the grate-shaped upper guide has been
removed, this procedure is unnecessary.
2)
Remove the screw [4], and remove the stopper [5].
3)
Remove the two screws [6], open the harness holder [7] at
three positions, and disconnect the connectors [8] at two posi-
tions.
three positions, and disconnect the connectors [8] at two posi-
tions.
4)
Insert your finger into the hole in the back of the No. 1 tray [9].
Push the tray lift motor gear [10] toward you to release the
clutch, and lift the No. 1 tray [9].
Push the tray lift motor gear [10] toward you to release the
clutch, and lift the No. 1 tray [9].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
[3]
[2]
[1]
[2]
[1]
[1]
[3]
[2]
[5]
[4]
[7]
[8]
[6]
[6]
[9]
[10]
MX-FN18 MAINTENANCE 4 – 17
h. Removal of No. 2 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the stopper [2].
2)
Remove the two screws [3], and disconnect the connector [4].
3)
Insert your finger into the hole in the back of the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
i. Removal of grate-shaped lower guide
1)
1)
Remove the ten screws [1], and remove the grate-shaped
lower guide [2].
lower guide [2].
CAUTION: When installing, be careful not to damage the grate-
shaped lower guide by hanging it to the sensor flag arm
on the delivery side.
on the delivery side.
j. PCB cover
1)
1)
Remove the seven screws [1], and remove the PCB cover [2].
[2]
[1]
[2]
[1]
[4]
[3]
[3]
[5]
[6]
[1]
[1]
[1]
[2]
[1]
[1]
[2]
MX-FN18 MAINTENANCE 4 – 18
k. Removal of inlet port feed unit
1)
1)
Disconnect the connectors [1] at four positions, and remove
the harness from the clamp [2].
the harness from the clamp [2].
2)
Remove the four screws [3].
3)
Open the upper cover [4], and remove the inlet port feed unit
[5].
[5].
l. Removal of saddle unit
1)
1)
Disconnect the two connectors [1], and remove the harness
from the clamp [2] at three positions.
from the clamp [2] at three positions.
2)
Remove the harness from the clamps [2] at two positions on
the bottom of the delivery side.
the bottom of the delivery side.
3)
Remove the two screws [4].
4)
Remove the three screws [5].
5)
Remove the saddle unit [6] from the paper feed side.
CAUTION: When installing saddle unit, arrange so that the Mylar
[1] on the top of the saddle section is on the outside of
the feed guide plate [2]. If it is installed on the inside,
feed operation may be faulty.
the feed guide plate [2]. If it is installed on the inside,
feed operation may be faulty.
[1]
[1]
[2]
[3]
[3]
[5]
[4]
[1]
[3]
[2]
[3]
[2]
[4]
[6]
[5]
[5]
[1]
[2]
MX-FN18 MAINTENANCE 4 – 19
(4) Stitcher base unit
a. Removal of front cover
1)
1)
Open the front cover [1], and remove the clip [2].
2)
Lift the front cover [1], and remove it.
b. Removal of saddle inlet front inside cover
1)
1)
Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
inside cover [2].
c. Removal of front inside upper cover
1)
1)
Remove the four screws [1], and remove the front inside upper
cover [2].
cover [2].
d. Removal of front inside lower cover
1)
1)
Remove the screw [1], and remove the roller knob [2].
2)
Remove the four screws [3], and remove the front inside lower
cover [4].
cover [4].
e. Removal of stitcher base unit
1)
1)
Remove the E-ring [1], and remove the shaft [2] and the roller
[3].
[3].
2)
Pull out the stitcher base unit [4] toward you.
(5) Positioning plate unit
a. Removal of front cover
1)
1)
Open the front cover [1], and remove the clip [2].
2)
Lift the front cover [1], and remove it.
[1]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[3]
[2]
[3]
[1]
[4]
[1]
[3]
[2]
[4]
[1]
[2]
Click on the first or last page to see other MX-FN18 service manuals if exist.