Sharp MX-FN18 Service Manual ▷ View online
MX-FN18 MAINTENANCE 4 – 8
1)
Remove the screw [1], and remove the stopper [2].
2)
Remove the two screws [3], and disconnect the connector [4].
3)
Insert your finger into the hole in the back of the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance so as not to
twist the tray cable.
fore, hold the tray at the bottom in advance so as not to
twist the tray cable.
i. Removal of grate-shaped lower guide
1)
1)
Remove the ten screws [1], and remove the grate-shaped
lower guide [2].
lower guide [2].
CAUTION: When installing, be careful not to damage the grate-
shaped lower guide by hanging it to the sensor flag arm
on the delivery side.
on the delivery side.
(7) Front inside upper cover
a. Removal of front cover
1)
1)
Open the front cover [1], and remove the clip [2].
2)
Lift the front cover [1], and remove it.
b. Removal of saddle inlet front inside cover
1)
1)
Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
inside cover [2].
[2]
[1]
[4]
[3]
[3]
[5]
[6]
[1]
[1]
[1]
[2]
[1]
[2]
[1]
[2]
[1]
MX-FN18 MAINTENANCE 4 – 9
c. Removal of front inside upper cover
1)
1)
Remove the four screws [1], and remove the front inside upper
cover [2].
cover [2].
(8) Front inside lower cover
a. Removal of front cover
1)
1)
Open the front cover [1], and remove the clip [2].
2)
Lift the front cover [1], and remove it.
b. Removal of saddle inlet front inside cover
1)
1)
Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
inside cover [2].
c. Removal of front inside upper cover
1)
1)
Remove the four screws [1], and remove the front inside upper
cover [2].
cover [2].
d. Removal of front inside lower cover
1)
1)
Remove the screw [1], and remove the roller knob [2].
2)
Remove the four screws [3], and remove the front inside lower
cover [4].
cover [4].
(9) PCB cover
a. PCB cover
1)
1)
Remove the seven screws [1], and remove the PCB cover [2].
[1]
[2]
[1]
[1]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[3]
[2]
[3]
[1]
[4]
[1]
[1]
[2]
MX-FN18 MAINTENANCE 4 – 10
B. Drive system
(1) Stapler
a. Removal of front cover
1)
1)
Open the front cover [1], and remove the clip [2].
2)
Lift the front cover [1] to remove it.
b. Removal of saddle inlet front inside cover
1)
1)
Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
inside cover [2].
c. Removal of front inside upper cover
1)
1)
Remove the four screws [1], and remove the front inside upper
cover [2].
cover [2].
d. Removal of stapler
1)
1)
Pull out the stapler, remove the screw [1], and remove the PCB
cover [2].
cover [2].
2)
Release the pawl [3], and remove the PCB [4].
3)
Disconnect the connectors [5] at three positions.
4)
Remove the screw [6], and remove the stapler with the stapler
base [7].
base [7].
CAUTION: When removing, be careful not to damage the plug [8].
5)
Turn back the stapler, and disconnect the connectors [9] at two
positions, and remove the two screws [10]. Remove the stapler
from the stapler base.
positions, and remove the two screws [10]. Remove the stapler
from the stapler base.
[1]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[2]
[1]
[8]
[5]
[3]
[4]
[7]
[6]
[10]
[9]
MX-FN18 MAINTENANCE 4 – 11
(2) Swing unit
a. Removal of front cover
1)
1)
Open the front cover [1], and remove the clip [2].
2)
Lift the front cover [1], and remove it.
b. Removal of rear cover
1)
1)
Shift the tray cable cover [1] to the tray side, and remove it.
2)
Remove the six screws [2], and lift and remove the rear cover
[3].
[3].
c. Removal of saddle inlet front inside cover
1)
1)
Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
inside cover [2].
d. Removal of front inside upper cover
1)
1)
Remove the four screws [1], and remove the front inside upper
cover [2].
cover [2].
e. Removal of left upper cover
1)
1)
Remove the two screws [1].
2)
With the upper door [2] open, tilt the left upper cover [3] to the
right and remove it.
right and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
[1]
[2]
[2]
[1]
[3]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[3]
[2]
[1]
[4]
Click on the first or last page to see other MX-FN18 service manuals if exist.