MX-C300P, MX-C300PE, MX-C300PL (serv.man3). Installation Manual — Sharp Copying Equipment Service Manual (repair manual)

Model
MX-C300P MX-C300PE MX-C300PL (serv.man3)
Pages
16
Size
1.62 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual
File
mx-c300p-mx-c300pe-mx-c300pl-sm3.pdf
Date

View Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) Service Manual online

Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
INSTALLATION MANUAL
CODE: 00ZMXC300PI1E
CONTENTS
MX- C300P/C300PE
MX- C300PL
MODEL
DIGITAL FULL COLOR PRINTER
   
Machine Environment, Installation, and Transportation
1 ] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1 - 1
[ 2 ] MX-C300P/C300PE/C300PL(MAIN UNIT)  . . . . . . . . . . . . . . . . .  2 - 1
[ 3 ] MX-CS11 (500 SHEET Paper Feed Unit)  . . . . . . . . . . . . . . . . . .  3 - 1
[ 4 ] Setting, Adjustments, Operation check
 . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 - 1
[ 5 ] Setup and adjustment data recording  . . . . . . . . . . . . . . . . . . . . .  5 - 1
[ 6 ] Necessary works before moving the machine . . . . . . . . . . . . . . .  6 - 1
CONTENTS
Machine Environment, Installation, and Transportation
1. Machine Environment and Installation  . . . . . . . . .
. . . . . . . i
2. Transit and delivery . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . .ii
[1] CONFIGURATION
1. System configuration. . . . . . . . . . . . . . . . . . . . . . .
1 - 1
2. Product list  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 - 1
3. Option list  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 - 1
[2] MX-C300P/MX-C300PE/C300PL (MAIN UNIT)
1. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 - 1
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 - 2
3. Image quality check  . . . . . . . . . . . . . . . . . . . . . . .
2 - 4
[3] MX-CS11 (500 SHEET PAPER FEED UNIT)
1. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 - 1
2. Adjustment  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 - 1
[4] Setting, Adjustments, Operation check
1. Firmware version check and version up . . . . . . . .
4 - 1
2. Function and operation check . . . . . . . . . . . . . . . .
4 - 1
[5] Setup and adjustment data recording . . . . . . . . . . . .
5 - 1
[6] Necessary works before moving the machine  . . . . .
6 - 1
  Machine Environment, Installation, and Transportation  -i
Service Manual
 
Machine Environment, Installation, and Transportation
1.Machine Environment and Installation
Before installing the machine, check that the following conditions are
satisfied.
If the installing (use) conditions are not satisfied, the machine may not
exhibit full performance, resulting in problems. It may also cause
safety problems. Using the following information, make sure all
aspects of installation, space, power, transportation, leveling, and
safety are met.
A.Transportation space
For installation of a large size machine, be sure to check that the door
size is wide enough before bringing in.
B.Installing space
The following space must be provided around the machine in order to
assure machine performance and proper operations.
If any option is installed, provide the additional space for with installa-
tion.
Adequate space must be provide behind the machine for proper venti-
lation of heat and dust. The machine will not function properly if heat
and dust cannot be properly expelled from the machine.
C.Power source (Capacity, voltage, frequency,
safety, plug)
If the power specifications are not satisfied, the machine cannot exhibit
full performance and may cause safety trouble.
Strictly observe the following specifications.
(1)Power capacity
Check that the following power capacity is satisfied. If not, additionally
provide a proper power source.
Current capacity
Japan: 20A or more
EX 100V: 15A or more
EX 200V: 10A or more
Check the shape of the power plug of the machine, and insert it into a
power outlet of the acceptable shape.
(2)Power voltage
Measure the voltage during copying to check that the voltage is in the
range of the specified voltage +/- 10%.
If the voltage is outside the specified range, please have a certified
electrician upgrade the outlet.
(Electrical work is required.)
Use of a step-up transformer is also available. In this case, the capac-
ity must be great enough for the max. power consumption of the
machine.
(3)Power frequency, waveform
The frequency must be within the range of the specified frequency +/-
2%. If the power waveform is improper, a problem may occur with the
machine.
(4)Safety
Be sure to properly ground the machine.
Grounding (earth connection) must be performed before inserting the
power plug into the power outlet.
When disconnecting the earth connection, be sure to disconnect the
power plug from the power outlet in advance.
(5)Power plug
Check the shape of the power plug of the machine, and insert it into a
power outlet of the acceptable shape.
Power plug stated in power capacity.
D.Installation place and level
Do not install machine on the unstable place like the unstable pedestal
or the tilted place. 
The installation place must be strong enough to safely support the
weight of the machine as well as any installed options.  
If the machine drops or falls down, it may cause an injury or a break-
down. 
If the unit is not properly leveled, toner density may become affected
degrading the print quality.
Also, color shift or image distortion may occur.
To assure proper Image quality, make sure the machine is sitting level.
E.Direct rays of the sun, dust, temperature, humid-
ity, gasses, chemicals, vibration
(1)Temperature and humidity (Environmental conditions)
This machine is designed to perform properly under the specified tem-
perature and humidity. If the temperature and humidity exceeds the
specified range, the machine may not operate properly and or cause
equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
Do not install the machine near a heater, an air conditioning outlet, or a
humidifier.
Condensation may form inside the machine causing multiple prob-
lems. Make sure machine has proper ventilation.
No.
Content
1
Transportation space
2
Installing space
3
Power source (Capacity, fluctuation, safety)
4
Floor strength
5
Direct rays of the sun, dust, temperature, humidity, gases, 
chemicals
  Machine Environment, Installation, and Transportation  -ii
Operational environment
Temperature: 10 to 35 degree C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
(2)Contaminates
If dust enters the machine, it may cause dirty copy and a paper jam,
resulting in a shortened lifetime.
(3)Direct sunlight
If the machine is installed in direct sunlight, the exterior of the machine
may be discolored and abnormal copies may be produced.
(4)Gases and chemicals
Do not install the machine at a place where there are gases and chem-
icals. Especially be careful to avoid installation near a diazo-type
copier, which produces ammonium gas.
Copy quality may be adversely affected and machine problems may
arise.
(5)Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
F.Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to observe
the following precautions in order to prevent against damage by static
electricity.
-
When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
-
When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:
-
Put an earth band to your arm, and connect it to the machine.
-
When repairing or replacing an electronic part, perform the pro-
cedure on an anti-static mat.
G.Note for proper drum, developing, fusing and
transfer unit handling
When handling the OPC drum, developing, fusing units and transfer
units, observe the following items.
Drum unit
-
To prevent  damage to the OPC drum, avoid working on the drum
unit in high intensity light areas.
-
When the OPC drum is removed from the machine, cover it with
light blocking material. (When using paper, use about 10 sheets of
paper to cover it.)
-
Be careful not to attach fingerprints, oil, grease, or other foreign
material on the OPC drum surface.
Transfer unit
-
Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the transfer roller, primary transfer belt and secondary
transfer roller.
Developing unit
-
Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the developing unit.
Fusing unit
-
Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the fusing roller.
-
If the machine is not going to be used for an extended period,
release the pressure on the fusing rollers.
If these items are neglected, a trouble may be generated in the copy
and print image quality.
2.Transit and delivery
A.Implements, facility, and manpower
It is recommended to use a forklift when moving the machine.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the install-
ing place.
B.Delivery
Remove the packing materials prior to installation in the office environ-
ment.
85%
Humidity㧔RH㧕
60%
20%
No.
Content
Method
1
Implements, facil-
ity, and man power
Use a forklift. (If no forklift is available, 
manpower of two persons is required.) 
2
Delivery
Transit must be made in packed condi-
tion.
Page of 16
Display

Download Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) Service Manual (Repair Manual)

Here you can view online or download Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) Service Manual in pdf. This Service Manual can help you recover, restore, fix, disassemble and repair Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) Copying Equipment. Information contained in Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).