Sharp MX-B201D (serv.man9) Service Manual ▷ View online
MX-B201/B201D DISASSEMBLY AND ASSEMBLY 8 - 17
：'11/Oct/17
1
8. Power section
A. List
B. Disassembly procedure
1) Disconnect each connector.
2) Remove the screw, and remove the earth line.
3) Remove two screws, and remove the power PWB unit.
C. Assembly procedure
For assembly, reverse the disassembly procedure.
9. Duplex motor section
(MX-B201D only)
A. List
B. Disassembly procedure
1) Remove the rear cabinet.
2) Remove two screws.
3) Remove the Duplex motor cover.
4) Remove the Duplex motor.
Note: When reassembling, be sure to engage the Duplex motor
gear with the belt on the main body side.
C. Assembly procedure
For assembly, reverse the disassembly procedure.
10. Reverse roller section
(MX-B201D only)
A. List
B. Disassembly procedure
1) Remove four screws.
2) Remove the spring, and the earth wire.
3) Remove the reverse unit.
4) Bend the reverse roller and remove it.
C. Assembly procedure
For assembly, reverse the disassembly procedure.
No.
Part name Ref.
1
Power PWB
1)
1)
1)
1)
2)
3)
4)
4)
5)
1)
1)
1
No.
Part name Ref.
1
Duplex motor
1
2
3
1
No.
Part name Ref.
1
Reverse roller
1
1
2
3
1
MX-B201/B201D DISASSEMBLY AND ASSEMBLY 8 - 18
11. RSPF section
A. Front cabinet, rear cabinet
(1)
Open the upper door unit.
(2)
Front cabinet and rear cabinet removal
1) Remove two screws.
2) Disengage the five pawls.
3) Remove the front cabinet and the rear cabinet.
B. Upper door unit
1) Release the shaft on the front side.
2) Remove the upper door unit.
C. Document tray unit
1) Release the shaft on the front side.
2) Remove the tray unit.
■ Note for reassembly
Use care so that the paper exit Mylar in not pinched between the
paper exit roller and the follower roller.
Use care so that the paper exit Mylar in not pinched between the
paper exit roller and the follower roller.
D. Upper door open/close sensor
1) Disconnect one connector.
2) Remove the upper door open/close sensor.
E. Reverse clutch, paper exit roller
(1)
Reverse clutch removal
1) Disconnect one connector.
2) Remove the resin E-ring.
3) Remove the reverse clutch.
■ Note for reassembly
Attach the stopper of the reverse clutch along with the rib on the
motor mounting plate.
Attach the stopper of the reverse clutch along with the rib on the
motor mounting plate.
1
1
2
2
2
2
2
1
3
3
1
2
1
2
2
1
1
3
2
MX-B201/B201D DISASSEMBLY AND ASSEMBLY 8 - 19
(2)
Paper exit roller removal
1) Remove the E-ring.
2) Slide the bearing.
3) Remove the paper exit roller.
4) Remove the E-ring.
5) Remove the bearing.
F. Drive unit
(1)
Transport unit removal
1) Disconnect four connectors.
2) Remove the harness from the clamp.
3) Remove the snap band.
4) Remove one screw.
5) Remove the earth wire.
6) Remove one screw.
7) Disconnect the RSPF harness.
8) Remove four screws.
9) Remove the transport unit.
■ Note for reassembly
Before assembly, be sure to check that the harness is passed
through the rib.
Before assembly, be sure to check that the harness is passed
through the rib.
Arrange the RSPF harness to the outside of the base tray so that it
is not pinched before assembly.
is not pinched before assembly.
(2)
Drive unit removal
1) Remove three screws.
2) Remove the drive unit.
(3)
Drive motor removal
1) Remove the gear.
2) Remove two screws.
3) Remove the drive motor.
■ Note for reassembly
Connect the connectors according to the arrow indication marked
on the motor mounting plate.
Connect the connectors according to the arrow indication marked
on the motor mounting plate.
3
4
1
2
5
1
1
3
6
7
5
4
1
1
2
8
8
8
9
1
1
2
1
3
2
1
MX-B201/B201D DISASSEMBLY AND ASSEMBLY 8 - 20
G. Shutter solenoid
(1)
Shutter solenoid unit removal
1) Remove the harness from the edge saddle.
2) Remove one screw.
3) Remove the shutter solenoid unit.
■ Note for reassembly
Install the paper feed solenoid under the state where the projection
of the paper feed planet arm is lower than the paper feed solenoid
lever.
Install the paper feed solenoid under the state where the projection
of the paper feed planet arm is lower than the paper feed solenoid
lever.
(2)
Shutter solenoid removal
1) Remove the paper feed solenoid spring from the shutter sole-
noid.
2) Remove the paper feed solenoid lever.
■ Note for reassembly
When assembling, use care so that the paper feed solenoid spring
does not extend out of the paper feed solenoid lever.
When assembling, use care so that the paper feed solenoid spring
does not extend out of the paper feed solenoid lever.
H. Pickup roller, take-up roller
(1)
Paper feed unit removal
1) Remove the E-ring.
2) Slide the bearing.
3) Remove the stopper arm.
4) Release the paper feed shaft pressure release spring.
5) Remove the paper feed unit.
6) Remove the paper feed shaft release arm.
(2)
Parts removal
1) Remove the E-ring.
2) Remove the resin E-ring.
3) Slide the shaft.
4) Remove the spring pin.
(3)
Paper feed roller removal
1) Pull out the shaft.
2) Remove the clutch boss and the clutch spring from the pickup
roller.
2
3
1
2
1
2
1
3
4
5
6
3
1
4
2
1
2
Click on the first or last page to see other MX-B201D (serv.man9) service manuals if exist.