DOWNLOAD Sharp MX-7090N / MX-8090N (serv.man3) Service Manual ↓ Size: 45.38 MB | Pages: 127 in PDF or view online for FREE

MX-8090N  MX-LCX3 N (LARGE CAPACITY TRAY)  5 – 7

1)

Slowly pull out the paper feed tray until it stops.

2)

Side plate size adjustment.

<1>
Loosen the wing bolt (A) on the front and the rear side of the
LCC upper part, and slide the handle to the neutral position.

<2>
Move the side plate to the desired paper size position.

<3>
Slide the handle to the desired paper size position, and lock it
and tighten the wing bolt (A).

3)

Rear edge plate size changeover

<1>
Lift the MC-CL handle at the top of the rear edge plate and
shift it to the desired paper size position.

<2>
Insert the lead edge of the movable shaft into the hole in the
lower section of the rear edge plate with the upper lever, and
lock the rear edge plate to the desired paper size position.

<3>
Push the large capacity tray into the closed (locked) position.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

A3/A4

12/A3W

11

8.5

A4R

B4/B5

A3/A4

12/A3W

11

8.5

A4R

B4/B5

MX-8090N  MX-LCX3 N (LARGE CAPACITY TRAY)  5 – 8

1)

Menu screen is displayed on the touch panel. Select the
[Paper Tray Settings].

2)

Select the paper size of LCC from contents of [Paper Tray Set-
tings].

Normally, Off-center adjustment is done by image processing using
CIS function. To check the mechanical off-center position, CIS
function needs to be turned off.

1)

Run Sim50-10 using the keypad on the main unit.

2)

Select "AH : SWT COR" and change the value “1” to “0”.

3)

Press [EXECUTE] key to print out for each paper feed tray.

4)

Check the void area of the adjustment pattern and check the
“Off-center” shift amount (A-B).

“A-B” is over 3mm: Move to Mechanical Adjustment . “A-B” is
less than 3mm:SWT COR "0"  to “1” for auto adjustment.

If you want to make further fine adjustments, refer to "Adjust-
ment with the simulation".

*This model has the automatic off-center adjustment function,
so it is different from the model with no function.

Since the off-center adjustment has been made at shipping, there
is normally no need to adjust. If the center is shifted, however,
adjust with the simulation. If the shift is not corrected, perform the
following steps to adjust.

1)

Slowly pull out the paper feed base tray until it stops.

When shifting the line of printing from the center of the paper in the
direction A of arrow as shown below:

1)

Loosen the blue off-center adjustment screws (each 2 pcs.),
and move the side plate by the dimension shifted in the direc-
tion A (R side), and tighten the loosened blue screws.

NOTE: Move the side plates by the same dimension on the

front side and the rear side.

2)

Push the large capacity tray into the closed (locked) position.

Then make a copy again to check to insure that there is no
shift. Repeat this procedure as required.

 

A 

B 

3ULQWHGVXUIDFH

3DSHUGHOLYHU\
GLUHFWLRQ

,IWKHGLPHQVLRQRI%LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVUHDUGLUHFWLRQ

,IWKHGLPHQVLRQRI$LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVIURQWGLUHFWLRQ

5HDU6LGH

)URQW6LGH

$%
$XWRPDWLFDGMXVWPHQWPP0HFKDQLFDODGMXVWPHQW

MX-8090N  MX-LCX3 N (LARGE CAPACITY TRAY)  5 – 9

When shifting the line of printing from the center of the paper in the
B direction of arrow as shown below:

1)

Loosen the blue off-center adjustment screws (each 2 pcs.),
and move the side plate by the dimension shifted in the direc-
tion B (F side), and tighten the blue screws.

NOTE: Move the side plates by the same dimension on the

front side and the rear side.

2)

Push the large capacity tray into the closed (locked) position.

Then make a copy again to insure that there is no shift. Repeat
this procedure as required.

1)

 Run SIM 50-10 using the keypad on the main unit. 

 The following screen appears. 

2)

This screen allows you to configure the print off-center adjust-
ment value for each paper feed tray. 

3)

On the touch panel, press [

] to select "K: 50 :MAIN-LCC." 

4)

Enter the desired adjustment value through the numeric key-
pad. 

(This value, which defaults to 50, can be adjusted within the
range of 1 to 99).

– Reducing the adjustment value by 1 causes the main scan/

print position to shift by 0.1 mm toward the rear. 

– Increasing the adjustment value by 1 causes the main scan/

print position to shift by 0.1 mm toward the front. 

5)

After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting. 

6)

Check that the adjustment pattern image is printed in the cor-
rect position.

Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met: 

No adjustment is needed if A - B = 0 +/- 3.0 mm.

If the above condition is not satisfied or you want to make fur-
ther fine adjustments, do the following.

7)

Change the adjustment value. 

(Enter a new adjustment value and press the [OK] key).

Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm. 

Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied. 

8)

After you have completed the adjustment, exit from simulation
mode by pressing the [CA] key.

A-B = 0    3.0mm

+

-

B

A

MX-8090N  MX-LCX3 N (LARGE CAPACITY TRAY)  5 – 10

Since the regulation plates are adjusted when shipping, there is
basically no need to readjust. If, however, there is skew, adjust the
regulation plate width and the diagonal feed in the following proce-
dures:

1)

Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the large
capacity tray.

2)

Set a sheet of paper on the paper feed base tray. Check that
the front regulation plate is at the marked center, and push it in
contact with the front regulation plate. Loosen the blue screws
of the rear regulation plate.

3)

Use the mark of the rear regulation plate, and fix the blue
screws at the position so that the clearance between paper
and the rear regulation plate is evenly 1mm.

NOTE: The positions of the regulation plates are even to the

right and left marks.

1)

Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.

2)

Adjust the diagonal feed.

Loosen the blue screw (A) on the front regulation plate.

Referring to the degree of diagonal feed, move the regulation
plate in the direction of (-) and fix the blue screw.

1mm

Diagonal feed 1

Transport

direction

Diagonal feed 2