DOWNLOAD Sharp MX-6580N / MX-7580N (serv.man4) Service Manual ↓ Size: 50.67 MB | Pages: 127 in PDF or view online for FREE

Model
MX-6580N MX-7580N (serv.man4)
Pages
127
Size
50.67 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual (Revised June 2017).
File
mx-6580n-mx-7580n-sm4.pdf
Date
PREV: Sharp MX-6580N / MX-7580N (serv.man3) Service Manual

Sharp MX-6580N / MX-7580N (serv.man4) Service Manual ▷ View online

MX-7580N  Transit, Installation (using) environment, Note  – ii
Operational environment
Temperature: 10 to 35
C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
Contaminates
If dust enters the machine, it may cause dirty copy and a paper jam,
resulting in a shortened lifetime.
Direct sunlight
If the machine is installed under the rays of the sun, the exterior of the
machine may be discolored and abnormal copies may be produced.
Gases and chemicals
Do not install the machine at a place where there are gases and chem-
icals. Especially be careful to avoid installation near a diazo-type
copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be caused.
* There was a trouble in a place where silicon-series gas or volatile
components are generated. Use great care for avoiding this.
Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to observe
the following precautions in order to prevent against damage by static
electricity.
• When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
• When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:
• Put an earth band to your arm, and connect it to the machine.
85%
Humidity㧔RH㧕
60%
20%
MX-7580N  Transit, Installation (using) environment, Note  – iii
• When repairing or replacing an electronic part, perform the proce-
dure on an anti-static mat.
G. Note for proper drum, developing, fusing and 
transfer unit handling
When handling the OPC drum, developing and transfer units, observe
the following items.
Drum unit
• To prevent  damage to the OPC drum, avoid working on the drum
unit in high intensity light areas.
• When the OPC drum is removed from the machine, cover it with
light blocking material. (When using paper, use about 10 sheets of
paper to cover it.)
• Be careful not to attach fingerprints, oil, grease, or other foreign
material on the OPC drum surface.
Transfer unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the transfer roller, primary transfer belt and secondary
transfer belt.
Developing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the developing unit.
Fusing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the fusing roller and the external heating belt.
• Do not leave the fusing roller in contact state for a long time.
If these items are neglected, a trouble may be generated in the copy
and print image quality.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the install-
ing place.
Since the hard disk drive is built in the machine, use care not to exert
vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office environ-
ment.
No.
Content
Method
1
Implements, facility, 
and man power
Use a forklift. (If no forklift is available, 
manpower of two persons is required.) 
2
Delivery
Transit must be made in packed condition.
MX-7580N  Transit, Installation (using) environment, Note  – iv
3. Power configuration
A. Indoor wiring (power outlet) and breaker information
NOTE:
• Prepare an indoor wiring (power outlet) which is connected to the AC plug of the machine and its option units. 
The required number of power outlets varies according to the combination of the option units. 
Prepare the necessary number of them.
Example: (North America) Finisher "2.9A", large-capacity multi-stage tray "8A"   12A>10.9A=2.9A+8A   Connectable to the same circuit 
(breaker).
• For the AC cord of an option unit, use another indoor wiring (another breaker) than that for the machine.
For North America only
• The machine power is of 200V, an indoor wiring work may be required.
For Europe only
• Both of AC code 1 and 2 can be connected together into 16A AC outlet in case, but if the power source is less than 16A in case, notice the following
rules.
• Use different indoor wiring (separate breaker) for each of the two AC cords of the machine.
• For additional installation of breakers and 200V indoor wiring, use professionals to do the jobs.
4K finisher 
(100-sheets 
binding)
Multi-
folding 
unit
Inserter
Decurler 
unit
Machine 1
Machine 2
Paper pass 
unit
Large-capacity 
multi-stage tray
AC cord type
Inlet
Inlet
---
---
Direct
---
---
Inlet
North 
America
65cpm 
machine
75cpm 
machine
Power supply 
rating
120V/2.9A
AC power 
is supplied 
from the 
finisher.
Power is 
supplied 
from the 
machine.
Power is 
supplied 
from the 
machine.
208-240V/12A
---
Power is 
supplied from 
the large-
capacity multi-
stage tray.
120V/8A
Power capacity
120V/15A
---
---
---
240V/20A
---
---
120V/15A
Form of the 
plug
---
---
---
---
---
Form of the 
power outlet
---
---
---
---
---
4K finisher 
(100-sheets 
binding)
Multi-
folding 
unit
Inserter
Decurler 
unit
Machine 1
Machine 2
Relay unit
Large-capacity 
multi-stage tray
AC cord type
Inlet
---
---
---
Inlet
Inlet
---
Inlet
Europe/
UK
65cpm 
machine
75cpm 
machine
Power supply 
rating
230V/1.5A
AC power 
is supplied 
from the 
finisher.
Power is 
supplied 
from the 
machine.
Power is 
supplied 
from the 
machine.
220-240V/8A
220-240V/8A
Power is 
supplied from 
the large-
capacity multi-
stage tray.
230V/4A
Power capacity
230V/10A
---
---
---
230V/10A
230V/10A
---
230V/10A
Form of the 
plug
---
---
---
---
Form of the 
power outlet
---
---
---
---
Machine
Paper feed system
After-process system
AC power 
supply
4K 
finisher 
(100-sheets 
binding)
Multi-
folding 
unit
Inserter
Decurler 
unit
Large-capacity 
multi-stage tray
Paper 
pass 
unit
MX-7580N  CONFIGURATION  1 – 1
MX-7580N
Service Manual
 
[1] CONFIGURATION
1.  System diagram
MX-7580N
MX-6580N
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
MX-LC12
LARGE CAPACITY
TRAY
MX-LT10
MX-TR14
EXIT TRAY UNIT
MX-LCX3 N
LARGE CAPACITY
TRAY
MX-MF11
MULTI BYPASS TRAY
MX-RB14
PAPER PASS
UNIT
MX-RB15
CURL CORRECTION
UNIT
MX-FD10
FOLDING UNIT
MX-CF11
INSERTER
MX-RB12
PAPER PASS
UNIT
MX-TU14
EXIT TRAY CABINET
MX-PN12A/B/C/D
PUNCH MODULE
MX-PN13
A/B/C/D
PUNCH MODULE
MX-FN20
SADDLE STTICH
FINISHER
MX-FN19
FINISHER
MX-FN22
SADDLE STTICH
FINISHER
MX-FN21
FINISHER
MX-TM10
TRIMMING
MODULE
MX-LC13 N
LARGE CAPACITY
TRAYS
MX-RB13
RELAY UNIT
LONG PAPER FEEDING TRAY
MX-SL10 N
STATUS INDICATOR
MX-US50
SHARPDESK 50 LICENSE
KIT
MX-USA0
SHARPDESK 100 LICENSE
KIT
MX-AMX1
APPLICATION
INTEGRATION MODULE
MX-AMX2
APPLICATION
COMMUNICATION MODULE
MX-AMX3
EXTERNAL ACCOUNT
MODULE
MX-FWX1
INTERNET FAX EXPANSION
KIT
MX-PF10
BARCODE FONT KIT
MX-FX15
FACSIMILE EXPANSION KIT
AR-SU1
STAMP UNIT
MX-KB13
KEYBOARD
MX-EB18
WIRELESS LAN ADPTOR
MX-PX12
INTERFACE KIT
MX-US10
SHARPDESK 10 LICENSE
KIT
MX-USX1
SHARPDESK 1 LICENSE KIT
MX-USX5
SHARPDESK 5 LICENSE KIT
MX-FR55U
DATA SECURITY KIT
Page of 127
Display

Click on the first or last page to see other MX-6580N / MX-7580N (serv.man4) service manuals if exist.

RANDOM: