Sharp MX-6500N / MX-7500N (serv.man12) Service Manual ▷ View online
MX-7500N MX-RB14 (PAPER PASS UNIT) 8 – 8
4) Install the dummy unit (Packed items No.1) and fix it with 4
screws (Packed items No.13).
5) Fix the ADU cabinet R lower (Packed items No.7) with a screw
(Packed items No.12).
6) Fix the ADU cabinet F lower (Packed items No.6) with 2
screws (Packed items No.12) and a screw (Packed items
No.13).
No.13).
B. Install the connection plate
1)
Remove the LCC cabinet.
2)
Install the LCC cabinet with turning over it.
3)
Before install LC13, fix the upper mounting plates (bundled
with LC13_packed items No.6) to the machine with the screws
(bundled with LC13_packed items No. 11 S-tight, M4 x 18).
with LC13_packed items No.6) to the machine with the screws
(bundled with LC13_packed items No. 11 S-tight, M4 x 18).
MX-7500N MX-RB14 (PAPER PASS UNIT) 8 – 9
4) Remove the screws and remove the covers.
Install the connecting plate lower F (Packed items No.8), con-
necting plate lower R (Packed items No.9) and fix it with 4
screws (Packed items No.13).
necting plate lower R (Packed items No.9) and fix it with 4
screws (Packed items No.13).
NOTE: Remove the front and rear covers, then remove the
screws (in the rear side only) as shown in the figure
below. (The removed screws are not used.)
below. (The removed screws are not used.)
C. Fix the upper door stopper L
1) Pierce the concave position on the front cabinet of the right
door.
NOTE: When opening a hole, clean and remove cutting scrap.
* The illustration is MX-6240/7040 series.
2) Fix the upper door stopper L (Packed items No.4) with the
screws (Packed items No.11).
* The illustration is MX-6240/7040 series.
D. Paper pass unit connection
1)
Lift the left side of the paper pass unit.
2)
Hook the fixing plate of the paper pass unit on the connection
plates of main unit, and lift and push the paper pass unit to
connect the main unit.
plates of main unit, and lift and push the paper pass unit to
connect the main unit.
Procedures to separate from the machine
1)
1)
Insert screwdriver into the hole in the transport section to
release lock of the connection plate with pressing RB14 to the
following direction as a figure below.
release lock of the connection plate with pressing RB14 to the
following direction as a figure below.
2)
Lift the left side, and release locks of the front and the rear of
the connection plate.
the connection plate.
MX-7500N MX-RB14 (PAPER PASS UNIT) 8 – 10
E. Connector connection
1) Remove the screw of the upper connector cover and remove
the cover from the main unit.
2) Connect the connector and tighten the screw.
F. Fix the front door
1) Fix the front door (Packed items No.3) with 6 screws (Packed
items No.12).
NOTE: Attch the front door after install LC13.
G. Fix the upper door stopper R
1)
Install the step screw (Packed items No.14).
2)
Hang the spring (Packed items No. 17).
3)
Slide the upper door stopper R (Packed items No. 5) in the
arrow direction and attach it with the step screw (Packed items
No.14).
arrow direction and attach it with the step screw (Packed items
No.14).
6WHSVFUHZ
TopPage
2
: ‘14/Jan
2
MX-7500N MX-RB14 (PAPER PASS UNIT) 8 – 11
4) Hang the spring on the upper door stopper R.
5) Install the washer large (Packed items No.15), washer small
(Packed items No.16) and screw (Packed items No.12).
H. Attach the upper door
Attach the upper door to the paper pass unit.
NOTE: Attch the Upper door after install LC13.
Click on the first or last page to see other MX-6500N / MX-7500N (serv.man12) service manuals if exist.