Sharp MX-5500N / MX-6200N / MX-7000N (serv.man75) Service Manual ▷ View online
MX-7000N MX-5500N/6200N/7000N 1 – 14
K. Tray setup
(1) Setting of paper size and paper type
Change the tray setting in the "system setting" mode. Some items
require the administrator authority for display. The paper setting (to
A4/recycle) procedure for tray 3 is as follows.
However, if size of the tray 1 has been switched to B5, execute SIM
26-2, and set the paper size.
1)
require the administrator authority for display. The paper setting (to
A4/recycle) procedure for tray 3 is as follows.
However, if size of the tray 1 has been switched to B5, execute SIM
26-2, and set the paper size.
1)
Press the [SYSTEM SETTINGS] key.
2)
Touch the [Paper Tray Settings] key.
3)
Touch the [Tray Settings] key.
4)
Touch the [Change] key.
5)
Select "recycled" on the selection box of the "Type". Select
"A4" on the selection box of the "Size". Touch the [OK] key.
"A4" on the selection box of the "Size". Touch the [OK] key.
(2) Tray size setup
a. Inch series tray 1, tray 2 (LT to A4)
1)
1)
Pull out the tandem cassette.
2)
Push down the paper feed base plate gently, hold the hooks
and remove A4 size regulation plate.
and remove A4 size regulation plate.
LOGOUT
LINE
PRINT
IMAGE SEND
DATA
DATA
READY
SYSTEM
SETTINGS
HOME
JOB STATUS
System Settings
Admin Password
Back
Total Count
Paper Tray
Settings
Printer Condition
Settings
Document Filing
Control
Address Control
Fax Data
Receive/Forward
USB-Device Check
Default Settings
List Print
(User)
System Settings
Paper Tray Settings
Back
Tray Settings
Paper Type Registration
Auto Tray Switching
Back
Change
Disable Punch
Disable Staple
Disable Duplex
Fixed Paper Side
Type
Plain
Auto-Inch
Tray Settings
Size
Tray 3
Doc. Filing
I-Fax
Fax
Print
Copy
Change
Disable Punch
Disable Staple
Disable Duplex
Fixed Paper Side
Type
Plain
Auto-Inch
Size
Tray 4
Doc. Filing
I-Fax
Fax
Print
Copy
2
3
OK
Cancel
System Settings
Tray Settings
Tray:
Type:
Size:
mm (148-432)
mm (100-297)
X
Y
Paper Property:
Tray 3
Recycle Paper
Auto-Inch
Fixed Paper Side
Disable Duplex
Disable Staple
1
2
1
1
3
3
3
3
2
2
MX-7000N MX-5500N/6200N/7000N 1 – 15
3)
Fit the A4 size regulation plate to A4 size, and attach it.
* Be careful to place and direction that install the sheet.
* Be careful to place and direction that install the sheet.
4)
Close the tandem cassette.
b. A4-B5 series tray 1 (A4 to B5)
* Except Europe, Australia, and New Zealand
1)
* Except Europe, Australia, and New Zealand
1)
Pull out the tandem cassette.
2)
Push down the paper feed base plate of the tray 1 gently, hold
the hooks and remove A4 size regulation plate. Remove the
sheet.
* Double the sheet that have been removed, and store it to the
the hooks and remove A4 size regulation plate. Remove the
sheet.
* Double the sheet that have been removed, and store it to the
tray 2.
3)
Push down the paper feed base plate of the tray 2 gently, hold
the hooks and remove A4 size regulation plate. Remove the
sheet.
the hooks and remove A4 size regulation plate. Remove the
sheet.
4)
Double the sheet that have been removed in step 2 and step 3,
and install the A4 size regulation plate.
* Double the sheet, and install it.
* Be careful to place and direction that install the sheet.
and install the A4 size regulation plate.
* Double the sheet, and install it.
* Be careful to place and direction that install the sheet.
1
3
3
2
2
1
2
3
2
3
MX-7000N MX-5500N/6200N/7000N 1 – 16
5)
Remove the rear end regulation plate F and R, and remove the
screw.
screw.
6)
Install the rear end regulation plate F and R, and fix with the
screw.
screw.
7)
Remove the screw, and remove the mylar sheet. Change the
installing direction and install with screws. (2 positions)
installing direction and install with screws. (2 positions)
8)
Open the waste toner bottle section cover.
9)
Remove the B5 size regulation plate.
10) Install the B5 size regulation plate to the tray 1.
11) Attach the A4 size regulation plate to inner side of the waste
toner bottle section cover.
1
1
2
2
3
3
MX-7000N MX-5500N/6200N/7000N 1 – 17
12) Close the waste toner bottle section cover.
13) Close the tandem cassette.
c. Tray 3, tray4
1)
1)
Pull out gently the tray 3/4 until it stops.
If paper remains in the tray, remove it.
If paper remains in the tray, remove it.
2)
Adjust the guide plates A and B by squeezing their lock levers
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.
L. Specifications setup
Used to set the specifications with SIM26 according to the cus-
tomer's request.
tomer's request.
To customize the following items after completion of the destination
setup, change the set values.
setup, change the set values.
M. Image quality check
Be sure to check the following items related to image quality. For
details of the adjustment and checking procedures, refer to the “[6]
ADJUSTMENT” on the Service Manual.
Check that the following items are normal. If not, carry out the
adjustment.
details of the adjustment and checking procedures, refer to the “[6]
ADJUSTMENT” on the Service Manual.
Check that the following items are normal. If not, carry out the
adjustment.
NOTE: When installing the copier, be sure to carry out the copy
color balance and the printer color balance.
1)
Image skew (see ADJ 8)
2)
Image resist (see ADJ 12)
3)
Image loss, void area (see ADJ 20)
4)
Copy color balance (Auto adjustment)
5)
Printer color balance (Auto adjustment)
(1) Copy color balance adjustment (Auto adjustment)
a. Note before execution of the copy color balance adjust-
ment (Auto adjustment)
• Be sure to use the specified paper for color.
b. Adjustment procedure
1)
1)
Enter the SIM 46-24 mode.
2)
Press [EXECUTE] key. (A3 or 11" x 17" paper is automatically
selected.)
The color patch image (adjustment pattern) is printed out.
selected.)
The color patch image (adjustment pattern) is printed out.
A
B
SIM No
Content
26
6
Used to set the destination.
SIM No
Content
26
2
Paper size setting of the Tray1/LCC.
3
Used to set the auditor specification mode.
5
Used to set the number (1 or 2) of count of paper
(A3 or WLT or 8K) that passes.
1:1pc 2:2pcs
* Targets: Total counter, maintenance counter,
(A3 or WLT or 8K) that passes.
1:1pc 2:2pcs
* Targets: Total counter, maintenance counter,
developer counter.
18
Used to set YES/NO of the toner save mode (Only
in UK and Japan versions)
* Carry out the setting by the user's program
in UK and Japan versions)
* Carry out the setting by the user's program
except the UK version.
1:accept 2:inhibit
52
Used to set whether non-printed paper (insertion
paper, cover paper) is counted up or not.
1:YES 2:NO
paper, cover paper) is counted up or not.
1:YES 2:NO
53
Used to set YES/NO of auto color calibration
permission.
1:accept 2:inhibit
permission.
1:accept 2:inhibit
65
Used to set the limit number of sheets for stapling.
1:limited 2:unlimited
1:limited 2:unlimited
SIMULATION NO.46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
EXECUTE
CLOSE
PRESS [EXECUTE] TO PROCON EXECUTIONAND PRINT THE TEST PATCH.
(PLEASE USE SPECIFIED TYPE OF A3 OR 11"
17" SIZE PAPER
FOR THIS ADJUSTMENT)
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man75) service manuals if exist.