Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual ▷ View online
MX-7000N MX-5500N/6200N/7000N 1 – 9
6)
Connect the connectors on front side and rear side.
7)
Engage the pawls to the toner hopper unit, and install it, and fix
with the screws.
with the screws.
8)
Shake the development unit horizontally a few times.
9)
Install the development unit.
10) Fix with the fixing screw.
11) Close the cover of the process section.
12) Tighten the screws. Push the fixing cover.
MX-7000N MX-5500N/6200N/7000N 1 – 10
13) Install the drum fixing knob so that fit to D-cutting part, and fix
with the screw.
14) Close the front cover.
E. Check of the waste toner bottle
1)
Open cover of the waste toner bottle section.
2)
Check that the waste toner bottle is installed securely.
3)
Close cover of the waste toner bottle section.
F. Installation of the paper exit tray
* The following procedure are the installation procedures of the
paper exit tray unit for North America and Australia, New
Zealand. Because it is standard equipment for another destina-
tion, the following procedure is unnecessary.
Zealand. Because it is standard equipment for another destina-
tion, the following procedure is unnecessary.
(1) Check the packed items
1)
Check that all the items are included in the Package.
(2) Installation of the IL interface harness
1)
Remove the screw, and remove the switch cover.
No.
Names of bundles
Quantity
1
Paper exit tray unit
1
2
Paper holding arm
1
3
Paper exit full detection actuator
1
4
IL interface harness
1
5
Screw (S tight M4x8)
4
1
2
3
4
5
MX-7000N MX-5500N/6200N/7000N 1 – 11
2)
Install the IL interface harness (Package part No. 4).
3)
Install the switch cover and fix it with a screw.
(3) Installation of the paper exit tray
1)
Remove the resin E ring, and remove the toner cover.
* Even if the toner cover remains being installed, the following
* Even if the toner cover remains being installed, the following
procedure is possible. However, remove it for the working
property.
property.
2)
Install the paper exit tray (Package part No. 1) to the main unit,
and fix with the screws (Package part No. 5).
and fix with the screws (Package part No. 5).
3)
Install the toner cover and fix it with a resin E ring.
(4) Installation of the paper holding arm and paper
exit full detection actuator
1)
Install the paper holding arm (Package part No. 2), and install
the paper exit full detection actuator (Package part No. 3).
* Check the size of the diameter of place where paper holding
the paper exit full detection actuator (Package part No. 3).
* Check the size of the diameter of place where paper holding
arm is installed.
6
4
MX-7000N MX-5500N/6200N/7000N 1 – 12
G. Set the control level for the reference toner
density
1)
Insert the power plug into the power outlet.
2)
Open the front cabinet. Turn ON the power switch in the front
cabinet of the main unit.
cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
4)
With the front cabinet open, enter the data for Sim.25-2.
5)
After the data input, close the cover.
6)
Select K, C, M, Y and then press the [EXECUTE] button. The
system then performs the simulation, samples the toner den-
sity control sensor value, and sets (stores in memory) the
average sensor detection level as the control level for the ref-
erence toner density.
system then performs the simulation, samples the toner den-
sity control sensor value, and sets (stores in memory) the
average sensor detection level as the control level for the ref-
erence toner density.
Note: Be sure to select all of the four colors: K, C, M, Y
7)
Exit from Simulation mode by pressing the [CA] key on the
main unit.
main unit.
"ON"
ON
ON
M
Y
C
K
0
AUTOMATIC DEVELOPER ADJUSTMENT
EXECUTE
AT DEVE ADJ_L_K
128
:
AT DEVEVO_L_Y
128
:
1/1
SIMULATION NO.25-02
TEST
CLOSE
AT DEVE ADJ_M_K
128
:
AT DEVE VO_M_Y
128
:
AT DEVE ADJ_L_C
128
:
AT DEVE VO_M_K
128
:
AT DEVE ADJ_L_M
128
:
AT DEVE VO_M_C
128
:
AT DEVE ADJ_L_Y
128
:
AT DEVE VO_M_M
128
:
AT DEVE ADJ_M_C
128
:
AT DEVE VO_H_K
128
:
AT DEVE ADJ_M_M
128
:
AT DEVE ADJ_M_Y
128
:
AT DEVE ADJ_H_K
128
:
AT DEVEVO_L_K
128
:
AT DEVEVO_L_M
128
:
AT DEVEVO_L_C
128
:
M
Y
C
K
0
AUTOMATIC DEVELOPER ADJUSTMENT
EXECUTE
AT DEVE ADJ_L_K
128
:
AT DEVEVO_L_Y
128
:
1/1
SIMULATION NO.25-02
TEST
CLOSE
AT DEVE ADJ_M_K
128
:
AT DEVE VO_M_Y
128
:
AT DEVE ADJ_L_C
128
:
AT DEVE VO_M_K
128
:
AT DEVE ADJ_L_M
128
:
AT DEVE VO_M_C
128
:
AT DEVE ADJ_L_Y
128
:
AT DEVE VO_M_M
128
:
AT DEVE ADJ_M_C
128
:
AT DEVE VO_H_K
128
:
AT DEVE ADJ_M_M
128
:
AT DEVE ADJ_M_Y
128
:
AT DEVE ADJ_H_K
128
:
AT DEVEVO_L_K
128
:
AT DEVEVO_L_M
128
:
AT DEVEVO_L_C
128
:
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man72) service manuals if exist.