Sharp MX-5500N / MX-6200N / MX-7000N (serv.man6) Handy Guide ▷ View online
33
22-04-2008
EFi System Software Installation
10. After installation is complete, perform the required steps as displayed:-
Note: Ensure the Fiery Print Controller has been powered off, both SW1 & SW2 DIP
switches returned to “Normal” mode (OFF) and all cables (Ethernet and Video I/F)
have been re-connected.
have been re-connected.
11. Click Next & Finish.
System Software Installation is complete.
34
22-04-2008
Firmware & Print Driver Revision
Engine Firmware
MX5500N, MX7000N
ICU (Main)
ICU (Boot)
PCU
SCU
NIC
Desk
Print Driver
PCL5c
PCL6
PS
PPD
For the latest Firmware and Print Driver version(s),please refer to the
Support Website.
35
22-04-2008
Test Simulations
The following pages contain information regarding test simulations. For a detailed description for
each test simulation, please refer to the MX5500-700 Service Manual.
each test simulation, please refer to the MX5500-700 Service Manual.
Copier Simulation Entry Codes
On the copier operation panel, press the following keys:-
Scanner Self Test
1
1
Scanner operations test
2
Scanner sensor check
5
Scanner unit and control circuit check
DSPF Self Test
2
1
DSPF ageing test.
2
DSPF sensor check
3
DSPF output check (motor, clutch, solenoid)
Finisher Operation / Test
3
2
Finisher sensor check.
3
Finisher output check (motor, clutch,
solenoid)
solenoid)
10
Finisher adjustment
30
Inserter sensor check
31
Inserter load check
32
Adjust Inserter paper width detection level
LCC Operation / Test
4
2
LCC sensor check
3
LCC output check
5
LCC clutch operation check
Lamp Operation / Test
5
1
LCD/LED test
2
Heater lamp load check
3
Copy lamp check
4
Discharge lamp check
System Load Operation / Test
6
1
Feed output check
2
Fan load check
3
Transfer operation check
4
MC & PTC cleaner operation check
Device Aging Operation / Test
7
1
Ageing test setting
6
Interval ageing cycle timer set up
8
Warm up time display setting
9
Printing colour select mode (colour)
High Voltage Operation / Test
8
1
Developer bias setting and output
2
MHV/Grid setting and output
6
Transfer setting and output
Duplex Operation / Test
9
2
ADU sensor check
3
ADU load & output check
Toner Motor Operation / Test
10
1
Toner motor operation check
2
Toner remaining quantity sensor check.
Clear / Cancel
13
--
Trouble cancel (U1 trouble).
Clear / Cancel
14
--
Trouble cancel (excluding U2/PF trouble).
Clear / Cancel
15
--
LCC trouble cancel (U6-09)
Clear / Cancel
16
--
U2 trouble cancel
*
*
PROGRAM
CLEAR
36
22-04-2008
Test Simulations
Clear / Cancel
17
--
PF trouble cancel
Maintenance Cycle Configuration
21
1
Maintenance cycle setting
Data Output / Check
22
1
Counter data display
2
Jam/trouble counter display
3
Jam history data display
4
Trouble code history data display
5
ROM version display
6
Data print mode
8
Document feed and output counter display
9
Paper feed counter display
10
Machine system display
11
Fax counter display
12
DSPF jam history display
13
Process cartridge counter display
19
Network scanner counter display
90
System setting list print
Print Data Output
23
2
Print jam/Trouble data print mode
80
Data print mode (paper feed)
Data Counter Clear
24
1
Jam/trouble counter clear
2
Paper feed counter clear
3
Document feed & output counter clear
4
Maintenance counter clear
5
Developer counter clear
6
Copy Counter clear
7
Drum correction counter clear
9
Print & other counter clear
10
Fax counter clear
15
Network scanner counter clear
30
Administrator password initialisation
31
Service password initialisation
DV Auto Adjustment / Monitor
25
1
Toner sensor output monitor (Process drive)
2
Auto developer adjustment setting
Device Configuration
26
2
LCC size set-up
3
Auditor setup
5
A3 Total/Maintenance counter set-up
6
Destination set-up
10
Network scanner trial mode set-up
18
Toner save operation
30
CE mark control setup
35
Trouble memory mode setting
38
Engine life over setting (Developer)
41
Pamphlet mode AMS operation
49
Copy speed mode setup (Postcard)
50
Function setting (B/W reverse, colour
mode, finisher)
mode, finisher)
52
Blank paper count mode setting
53
Enable/Disable auto colour calibration
54
Enable/Disable auto calibration for printer
65
Finisher alarm set-up (stapled sheets)
67
Summer time & time zone configuration
69
Toner near end setting
Communication Configuration
27
1
RIC/Modem U7-00 detection set-up
2
FSS Function setting (no. registration)
4
FSS Function setting (call initialising)
5
Tag number setting
6
Manual service call enable
7
FSS Function setting (enable alert)
9
Paper feed timing threshold
10
Trouble History clear
11
Adjustment data output check (RIC/Modem)
12
Adjustment data output check (process)
13
Adjustment data output check
14
FSS Function test mode
Sensor Operation / Test
30
1
Main unit sensor check
2
Tray sensor check (main)
Bypass Operation / Adjustment
40
2
Bypass tray width adjustment
7
Bypass tray width detection manual setting
12
Tray 3 paper width detection adjustment
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man6) service manuals if exist.