DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man6) Service Manual ↓ Size: 942.82 KB | Pages: 52 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man6)
Pages
52
Size
942.82 KB
Type
PDF
Document
Handy Guide
Brand
Device
Copying Equipment / HANDYGUIDE VERSION 1.1
File
mx-5500n-mx-6200n-mx-7000n-sm6.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man6) Handy Guide ▷ View online

21
22-04-2008
Parts Compatibility
Description
MX5500N
MX6200N
MX7000N
PWB (200V Series):
MFP Control PWB (ICU)
CPWBX1701DS528
CPWBX1701DS548
CPWBX1701DS568
OPE PWB
CPWBF1704FCE18
LVDS PWB
CPWBN1703FCE18
SCU PWB
CPWBX1713DS568
CPWBX1713DS578
CPWBX1713DS588
PCU PWB
CPWBX1700FCE18
CPWBX1700FCE28
CPWBX1700FCE38
DC Power Supply
RDENC0055FCPZ
AC Power Supply
Driver (Main) PWB
CPWBN1699FCE18
Tandem PWB
CPWBF1706FCE18
Mother PWB
CPWBX1718FCE18
HVU (Main Charge)
RDENC0052FCPZ
RDENC0053FCPZ
HVU (Primary Transfer)
RDENC0063FCPZ
HVU (Second Transfer)
RDENC0059FCPZ
Heater Lamp PWB
CPWBN1726FC318
Operation Panel unit
CPNLC0269DS53
Optical Section:
CCD
CPLTM6526DS51
Copy Lamp
RLMPD0703FCZZ
C/Lamp Inverter PWB
CPWBF1678FC31
Process Section:
DV Unit - Black
DUNT-7734FCZZ
DV Unit - Cyan
DUNT-7823DSZZ
DV Unit - Magenta
DUNT-7823DS11
DV Unit - Yellow
DUNT-7823DS12
LSU
DUNT-7702FCZZ
DUNT-7702FC11
DUNT-7702FC12
Polygon Motor
TBA
P/Feed & Transport:
Pick Up Roller (All)
NROLR1467FCZ1
P/Feed Roller (All)
NROLR1466FCZ1
Separator Roller (All)
NROLR1466FCZ1
Fusing Section (200V series):
Heater Lamp Main U
RLMPU0725FCPZ
Heater Lamp Sub U
RLMPU0727FCPZ
Lower Heater Lamp
RLMPU0730FCPZ
Lower Heater Lamp Sub
RLMPU0733FCPZ
Non-contact Thermistor U
RDTCT0180FCZZ
Contact Thermistor U
RDTCT0169FCZ2
Thermostat
RTHM-0030FCZZ
Contact Thermistor L
RDTCT0170FCZ1
Document Feeder:
Paper Feed Roller
NROLR1462FCZZ
Pick Up Roller
NROLR1475FCZZ
Separation Roller
NROLR1476FCZZ
Special Tools:
Starting Powder 
(Stearic Acid)
UKOG-0312FCZZ
ID Calibration Jig
UKOG-0318FCZZ
Other
Centre Tray Unit
DUNT-7825DS11
22
22-04-2008
Coin Vend Interface
All MX series machines have a coin vend interface located on the PCU Main PWB. The vending
device activates various signals to indicate paper sizes and operation.
Because of additional functionality, the interface connector has been changed from 12 to 16 pins.
Connector Manufacture:
JST  (
www.jst.com
)
Connector Type
PND series
Connector Part Code (Wire Side)
PNDP-16V-Z
Before connecting a third party auditor, the device should confirm to the following:-
1.  The auditor interface should be optically isolated from the copier.
2.  The device should be Power Supply Unit independent.
3.  The device power supply unit should be a plug top adapter, not internal.
4.  The plug top adapter should have a reinforced insulation barrier.
5.  The audit device MUST hold a CE Mark.
To enable coin vend function, test simulation 26 –03 should be set as required:-
Insuffiecient money during copy job
The specified
quantity is
completed.
Remainder of
money is left
Black/Colour
(No money
remaining)
Colour
(Remainder of
money left)
The specified
quantity is
completed.
No money
remaining
Diagnostic
Setting
Condition 1
Condition 2
Condition 3
Condition 4
MODE 1
Operation 1
Operation 2
Operation 2
Operation 1
MODE 2
Operation 1
Operation 1
Operation 2
Operation 1
MODE 3
Operation 1
Operation 3
Operation 2
Operation 3
OPERATION 1
Wait for auto clear setting time
(Default 60sec – can be changed by the system setting)
OPERATION 2
Auto clear is not made.
OPERATION 3
Setting is immediately cleared.
Cont’d
23
22-04-2008
Coin Vend Interface
Connector Signals
Pin No.
PCU PWB (CN17)
1
+ 24v
Out
2
GND
Out
3
CV_B/W_COPY
In
4
CV_COUNT
Out
5
CV_START
Out
6
CV_CA
Out
7
CV_COLOUR_ COPY
In
8
CV_COLOUR1
Out
9
CV_STAPLE
Out
10
CV_COLOUR0
Out
11
CV_DUPLEX
Out
12
5v
Out
13
CV_SIZE0
Out
14
CV_SIZE1
Out
15
CV_SIZE2
Out
16
CV_SIZE3
Out
Colour Signal
Colour Mode
Colour Mode 1
(CL-COLOR0)
Colour Mode 2
(CL-COLOR1)
B/W
0
0
Full Colour
1
1
Others
(Single/Two Colour)
0
1
Paper Size Signals
SIZE3
SIZE2
SIZE1
SIZE0
PAPER SIZE
0
0
0
0
NIL
0
0
0
1
A3
1
0
1
1
A3W
0
0
1
0
A4
0
0
1
1
LT
0
1
0
0
B4
0
1
0
1
LG
0
1
1
0
WLT
0
1
1
1
INV
1
0
0
0
B5
1
0
1
0
A5
1
0
0
1
EXTRA
24
22-04-2008
Product Key Registration
Procedure
1.  Make a note of the Copier Serial Number upon which the option is to be installed.
For MX5500-7000N, the serial number can be obtained from the following menu:-
Custom Settings – Admin Authentication (Password) – Product Key – Serial Number
2.  Make a note of the Application number from the front of the option Operation Manual.
3.  Access the following URL, with the user name and password indicated
http://dse-pub.sharp.co.jp/key/
User Name:
keyuser
Password:
key000323
4.  Select your region.
5.  Register the option(s) against the Sharp Copier Serial Number by completing the following
Web form.
As shown, multiple options can now be registered at the same time:-
Note: When inputting the data, please ensure that the prefix letter of the Application
number is entered in UPPERCASE. Also, if the machine serial number ends in X or Y, that
must also be entered in UPPERCASE.
6.  Click Send.
The Product Activation Key(s) will then be displayed. Also, an E-mail confirmation will
be sent to the E-Mail address of the dealer representative.
Enter the Product Key and enable the option(s) from within the following menu:-
Custom Settings – Admin Authentication (Password) – Product Key
     Product Key activation is complete
Page of 52
Display

Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man6) service manuals if exist.