Sharp MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man7) Service Manual ▷ View online
MX-5141N ADJUSTMENTS AND SETTINGS 5 – 74
4)
Press [EXECUTE] key.
The color balance and the density are automatically adjusted.
The adjustment pattern is printed out. Check it for any abnor-
mality.
mality.
5)
Press [OK] key.
The list of the adjustment items (for each dither) is displayed.
6)
Select an adjustment item (for each dither).
*1: When performing adjustments in the heavy paper mode,
load paper in the manual paper feed tray.
7)
Press [EXECUTE] key.
A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.
The patch image (adjustment pattern) is printed out.
In the monochrome mode, only the monochrome pattern is
printed.
printed.
8)
Set the patch image (adjustment pattern) printed in the proce-
dure 7) on the document table so that the thin lines on the
printed patch image (adjustment pattern) are on the left side.
Place 5 sheets of white paper on the printed patch image
(adjustment pattern).
dure 7) on the document table so that the thin lines on the
printed patch image (adjustment pattern) are on the left side.
Place 5 sheets of white paper on the printed patch image
(adjustment pattern).
9)
Press [EXECUTE] key.
The color balance and the density are automatically adjusted,
and the machine goes to the state of procedure 6).
and the machine goes to the state of procedure 6).
To complete the adjustment and enable the adjustment result,
press [OK] key.
press [OK] key.
10) Make a copy, and check the copy image quality.
(Refer to the item of the printer color balance and density
check.)
check.)
NOTE: Use SIM46-52 to reset the adjustment values to the default
values.
Select item
(Mode/Image)
Content
Heavy Paper *
1
Adjustment item to improve the color balance in the
heavy paper mode
heavy paper mode
Black Edge
Adjustment item (K) to improve the reproduction of lines,
text density, and thickness
text density, and thickness
Color Edge
Adjustment item (Color) to improve the reproduction of
lines, text density, and thickness
lines, text density, and thickness
B/W
Adjustment item to improve the density and gradation in
the monochrome text mode and the map mode.
the monochrome text mode and the map mode.
Color Ed
Adjustment item to improve the color balance in the text
mode and the map mode.
mode and the map mode.
B/W 600dpi
Adjustment item to improve the density and gradation in
the monochrome printed photo mode and the
photography mode.
the monochrome printed photo mode and the
photography mode.
WOVEN1
Adjustment item when adjusting the watermark density
in the watermark mode 1
in the watermark mode 1
WOVEN2
Adjustment item when adjusting the watermark density
in the watermark mode 2
in the watermark mode 2
WOVEN3
Adjustment item when adjusting the watermark density
in the watermark mode 3
in the watermark mode 3
WOVEN4
Adjustment item when adjusting the watermark density
in the watermark mode 4
in the watermark mode 4
MX-5141N ADJUSTMENTS AND SETTINGS 5 – 75
11-D
(17)
Dropout color adjustment
(Normally not required)
Dropout color adjustment
(Normally not required)
a. General
This adjustment is used to adjust the range of reproduction of color
document images as monochrome images in the image send mode
(monochrome manual text mode).
document images as monochrome images in the image send mode
(monochrome manual text mode).
In other words, it is used to adjust the level of chroma of color
images which are reproduced as monochrome images.
images which are reproduced as monochrome images.
This adjustment must be performed in the following cases:
* When there is request from the user.
b. Adjustment procedures
1)
Enter the SIM 46-55 mode.
2)
Enter the adjustment value with 10-key and press [OK] key.
When the adjustment value is increased, colors dropout
becomes easy to narrow the reproduction range. When the
adjustment value is decreased, color dropout becomes difficult
to widen the reproduction range.
becomes easy to narrow the reproduction range. When the
adjustment value is decreased, color dropout becomes difficult
to widen the reproduction range.
3)
Scan the document in the image send mode (monochrome
manual text mode) and check the adjustment result.
manual text mode) and check the adjustment result.
Effect and adverse effect when decreasing the value
[Effect]
When black characters are fainted by color shift, etc, the black area
is outputted clearly.
is outputted clearly.
[Adverse effect]
Dropout of color sections becomes difficult.
Effect and adverse effect when increasing the value
[Effect]
Colors (of low chroma) which are difficult to be dropped out can be
dropped out.
dropped out.
[Adverse effect]
Black characters are fainted or cracked.
Item/Display
Content
Setting
range
Default
value
A
CHROMA
Dropout color range adjustment
0 - 6
3
SIM value 3
(Default)
SIM value 6
(Maximum value)
SIM value 0
(Minimum value)
The reproduction range is widened.
The reproduction range is narrowed.
When black characters
are fainted,
are fainted,
Document
Decrease the adjustment value.
When the color section is not
dropped out,
dropped out,
Increase the value.
Reproduced
image
image
Color dropout
MX-5141N ADJUSTMENTS AND SETTINGS 5 – 76
11-D
(18)
Watermark adjustment
(Normally not required)
Watermark adjustment
(Normally not required)
a. General
This adjustment is used to adjust the reproduction capability of the
watermark in the copy/printer mode.
watermark in the copy/printer mode.
This adjustment is used for watermark documents (primary output).
The result of this adjustment affects the result of watermark print
(secondary output).
The result of this adjustment affects the result of watermark print
(secondary output).
In the printer mode, the watermark density can be adjusted by the
printer driver. That adjustment is based on the result of this adjust-
ment.
printer driver. That adjustment is based on the result of this adjust-
ment.
This adjustment must be performed in the following cases:
* When there is request from the user. (When a satisfactory result
is not obtained from the adjustment in the system setting mode.)
* When there is request from the user. (When a satisfactory result
is not obtained from the adjustment with the printer driver.)
b. Adjustment procedures
1)
Enter the SIM 46-66 mode.
2)
Select the PATTERN mode, then select an adjustment item in
the following list according to the situation.
the following list according to the situation.
NOTE: Normally there is no need to adjust the PATTERN mode
(items K and L), the COPY MODE, and the POSITION
mode.
mode.
Item/Display
Content
Setting
range
Default
value
Description
NOTE
A
WOVEN DEN BK LOW
Watermark density level
(Color: Black / Adjustment for light
images)
(Color: Black / Adjustment for light
images)
0 - 255
15
The adjustment value is changed to increase or
decrease the density of the watermark of
background documents (primary output).
To increase the watermark density, increase the
adjustment value.
To decrease the watermark density, decrease the
adjustment value.
decrease the density of the watermark of
background documents (primary output).
To increase the watermark density, increase the
adjustment value.
To decrease the watermark density, decrease the
adjustment value.
NOTE:
When the adjustment value is increased,
the watermark area which is originally not
reproduced becomes difficult to disappear.
When the adjustment value is decreased,
the watermark area which is originally
reproduced becomes easy to disappear.
the watermark area which is originally not
reproduced becomes difficult to disappear.
When the adjustment value is decreased,
the watermark area which is originally
reproduced becomes easy to disappear.
B
WOVEN DEN BK MIDDLE
Watermark density level
(Color: Black, Density: Standard)
(Color: Black, Density: Standard)
0 - 255
19
C
WOVEN DEN BK HIGH
Watermark density level
(Color: Black, Density: Dark)
(Color: Black, Density: Dark)
0 - 255
23
D
WOVEN DEN C LOW
Watermark density level
(Color: Cyan / Adjustment for light
images)
(Color: Cyan / Adjustment for light
images)
0 - 255
19
E
WOVEN DEN C MIDDLE
Watermark density level
(Color: Cyan, Density: Standard)
(Color: Cyan, Density: Standard)
0 - 255
23
F
WOVEN DEN C HIGH
Watermark density level
(Color: Cyan, Density: Dark)
(Color: Cyan, Density: Dark)
0 - 255
27
G
WOVEN DEN M LOW
Watermark density level
(Color: Magenta / Adjustment for
light images)
(Color: Magenta / Adjustment for
light images)
0 - 255
15
H
WOVEN DEN M MIDDLE
Watermark density level
(Color: Magenta, Density:
Standard)
(Color: Magenta, Density:
Standard)
0 - 255
18
I
WOVEN DEN M HIGH
Watermark density level
(Color: Magenta, Density: Dark)
(Color: Magenta, Density: Dark)
0 - 255
21
J
CONTRAST
Contrast adjustment
0 - 255
2
This is used to adjust the variation in the watermark
density when the adjustment value of the watermark
print/contrast adjustment in the system setting is
changed by 1.
When this value is increased, the variation is also
increased. When the value is decreased, the
variation is also decreased.
When the adjustment value is 0, the result of the
contrast adjustment is not reflected.
(* The adjustment value must be set to 1 or greater.)
density when the adjustment value of the watermark
print/contrast adjustment in the system setting is
changed by 1.
When this value is increased, the variation is also
increased. When the value is decreased, the
variation is also decreased.
When the adjustment value is 0, the result of the
contrast adjustment is not reflected.
(* The adjustment value must be set to 1 or greater.)
K
HT TYPE (POSI)
For half-tone index watermark type
positive
positive
42 - 43
42
To reproduce the containing characters of watermark
copy (secondary output) more clearly, set to 43.
In that case, however, the containing characters of
the watermark document (primary output) can be
easily reproduced.
copy (secondary output) more clearly, set to 43.
In that case, however, the containing characters of
the watermark document (primary output) can be
easily reproduced.
Normally
set to the
default.
set to the
default.
L
HT TYPE (NEGA)
For half-tone index watermark type
negative
negative
42 - 43
42
To reproduce the containing characters of watermark
copy (secondary output) more clearly, set to 43.
In that case, however, the containing characters of
the watermark document (primary output) can be
easily reproduced.
copy (secondary output) more clearly, set to 43.
In that case, however, the containing characters of
the watermark document (primary output) can be
easily reproduced.
MX-5141N ADJUSTMENTS AND SETTINGS 5 – 77
Changing adjustment values of adjustment items A - I and
trade off
trade off
3)
Enter the adjustment value with 10-key and press [OK] key.
4)
Make a copy, and check the adjustment result.
Descriptions on the watermark
Kinds of
watermarks
(Mode
selected in
the watermark
copy mode)
Density
value
Adjustment
values of
adjustment
items A - I
Effect
Characters
appearing.
appearing.
Decrease.
The adjustment
value is
decreased.
value is
decreased.
The watermark images
become easy to
disappear.
The containing
characters become
lighter.
become easy to
disappear.
The containing
characters become
lighter.
Increase.
The adjustment
value is
increased.
value is
increased.
The containing
characters become
darker.
The watermark images
become difficult to
disappear.
characters become
darker.
The watermark images
become difficult to
disappear.
Background
appearing.
appearing.
Decrease.
The adjustment
value is
decreased.
value is
decreased.
The containing
characters become easy
to disappear.
The watermark images
become easy to
disappear.
characters become easy
to disappear.
The watermark images
become easy to
disappear.
Increase.
The adjustment
value is
increased.
value is
increased.
The watermark images
become darker.
The containing
characters become
difficult to disappear.
become darker.
The containing
characters become
difficult to disappear.
Document
(Copy document or
Print data)
(Copy document or
Print data)
Watermark document
(Primary output)
(Copy or Printer output)
(This machine)
(Primary output)
(Copy or Printer output)
(This machine)
Watermark copy
(Secondary output)
(This machine or other
company's machine)
(Secondary output)
(This machine or other
company's machine)
Copy / Print
Copy
COPY INHIBITED
COPY INHIBITED
COPY INHIBITED
Containing
characters
characters
Watermark
color
color
The watermark color is available in Cyan, Magenta, and
Black.
Black.
Containing
characters
characters
Characters embedded in a watermark, such as "COPY
INHIBITED," are called containing characters.
INHIBITED," are called containing characters.
Kinds of
watermarks
watermarks
There are two kinds: "Character appearing" and
"Background appearing."
When a watermark of "Character appearing" is copied, the
background disappears and the containing characters
appear.
When a watermark of "Background appearing" is copied,
the watermark of the character area disappears and the
containing characters become outline characters.
"Background appearing."
When a watermark of "Character appearing" is copied, the
background disappears and the containing characters
appear.
When a watermark of "Background appearing" is copied,
the watermark of the character area disappears and the
containing characters become outline characters.
Principle of
watermarks
watermarks
A watermark is composed of two dots: fine dots and rough
dots.
Since fine dots disappear when copied, they are called
disappearing patterns.
Since rough dots remain when copied, they are called
remaining patterns.
In a watermark of "Character appearing," the background is
a disappearing pattern and the containing characters are
remaining patterns.
In a watermark of "Background appearing," the background
is a remaining pattern and the containing characters are
disappearing patterns.
dots.
Since fine dots disappear when copied, they are called
disappearing patterns.
Since rough dots remain when copied, they are called
remaining patterns.
In a watermark of "Character appearing," the background is
a disappearing pattern and the containing characters are
remaining patterns.
In a watermark of "Background appearing," the background
is a remaining pattern and the containing characters are
disappearing patterns.
NOTE:
Note for
watermarks
Note for
watermarks
Watermarks have the following characteristics:
- A watermark is presumed to be synthesized with text
- A watermark is presumed to be synthesized with text
documents. If it is used with photos or images, the
containing characters may be seen in the watermark
document (primary output) or the containing characters
may not appear properly in the watermark copy
(secondary output).
containing characters may be seen in the watermark
document (primary output) or the containing characters
may not appear properly in the watermark copy
(secondary output).
- When a watermark is synthesized with newspapers or
other dark-background documents, the containing
characters may not appear in the watermark copy
(secondary output).
characters may not appear in the watermark copy
(secondary output).
- Containing characters may not appear in the watermark
copy (secondary output) depending on the kind of the
copier which makes the watermark copy (secondary
output) and the copy mode.
copier which makes the watermark copy (secondary
output) and the copy mode.
- Containing characters may not appear clearly in the
watermark copy (secondary output) depending on the
copy mode in which the watermark document (primary
output) is made.
copy mode in which the watermark document (primary
output) is made.
- When the print engine status changes, the containing
characters may not be concealed properly in the
watermark document (primary output). In this case,
follow the procedures below to conceal the containing
characters.
* Use SIM46-24 to execute the color balance
watermark document (primary output). In this case,
follow the procedures below to conceal the containing
characters.
* Use SIM46-24 to execute the color balance
adjustment.
* Use SIM46-54 to execute the color balance
adjustment for each dither.
* Adjust the watermark print contrast in the system
setting.
- Though the watermark of cyan or magenta is selected in
the black and white mode, the black watermark is
synthesized.
synthesized.
- For a document which is judged as monochrome with
ACS selected, though the watermark color is specified as
cyan or magenta, the black watermark is synthesized.
cyan or magenta, the black watermark is synthesized.
- The preview screen of the watermark only indicates the
setting of the watermark color, and does not indicate an
actual copy image.
actual copy image.
- When the document control (printer mode) is used
together, it is advisable to use "Characters appearing"
setting. If "Background appearing" setting is used
together, the detection accuracy of document control
may be reduced.
setting. If "Background appearing" setting is used
together, the detection accuracy of document control
may be reduced.
- In the printer mode watermark, setting of 1200dpi and a
watermark cannot be used together.
Click on the first or last page to see other MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man7) service manuals if exist.