Sharp MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man16) User Manual / Operation Manual ▷ View online
OPERATION GUIDE - CLEANING THE LASER UNIT
file:///G|/Documents/Products/MX4111_5111N/Operation%20Manual/MX511X_0170R1_ex_ope/contents/01-050b.htm[23/03/2012 12:16:55 PM]
MX-4110N / MX-4111N / MX-5110N / MX-5111N / MX-4112N / MX-5112N
CLEANING THE LASER UNIT
CLEANING AND REPLACEMENT
<
12
steps in all >
Open the front cover.
Take out the cleaning tool
for the laser unit.
The cleaning tool is attached to the
front cover.
(1) Pull the right-hand side of the
cleaning tool to detach it from the
hook.
(2) Put it over the hook to place it on
the back side.
(3) Turn the cleaning tool around the
boss to detach it from the left hand
hook.
Make sure that the cleaner
at the tip of the cleaning
tool is not dirty.
If the cleaner is dirty, remove the
cleaner from the cleaning tool and
replace it with a clean one. For the
procedure for replacing the cleaner,
see steps 4 through 6. If the cleaner
is not dirty, go to step 7.
OPERATION GUIDE - CLEANING THE LASER UNIT
file:///G|/Documents/Products/MX4111_5111N/Operation%20Manual/MX511X_0170R1_ex_ope/contents/01-050b.htm[23/03/2012 12:16:55 PM]
Open the inner cover and
take out a replacement
cleaner.
Replacement cleaners are stored on
the inner cover.
Grasp the end of the cleaner and pull
it out of the cover.
Remove the dirty cleaner
from the tip of the cleaning
tool.
While firmly grasping the tool where
the cleaner is attached, use your
other hand to press down on the
hook that secures the cleaner, and
remove the cleaner.
Attach the new cleaner to
the cleaning tool.
Align the cleaner hook with the
attachment hole in the cleaning tool.
Hold the cleaner firmly and push the
cleaning tool in.
Put the removed cleaner back on the inner cover. After replacing the
cleaner, be sure to close the inner cover.
OPERATION GUIDE - CLEANING THE LASER UNIT
file:///G|/Documents/Products/MX4111_5111N/Operation%20Manual/MX511X_0170R1_ex_ope/contents/01-050b.htm[23/03/2012 12:16:55 PM]
Point the cleaner down and
slowly insert the tool into
the hole that you wish to
clean.
Be sure to point the cleaner down.
Labels similar to (A) are attached to
areas that require cleaning.
Insert the cleaning tool all
the way into the hole and
then pull it back out.
Pull the cleaning tool out until you
feel the tip of the tool leave the
cleaning surface of the laser unit.
Repeat step 8 two or three
times and then remove the
cleaning tool.
Repeat steps 7 to 9 to clean
all holes (4 holes) in the
laser unit.
There are a total of four holes to be
cleaned in the laser unit.
Clean all holes.
Replace the cleaning tool.
(1) Engage the cleaning tool onto the
boss and turn it around it, and then
put the edge (the cleaner side) on
the left hand hook.
(2) Put the right-hand side of the
OPERATION GUIDE - CLEANING THE LASER UNIT
file:///G|/Documents/Products/MX4111_5111N/Operation%20Manual/MX511X_0170R1_ex_ope/contents/01-050b.htm[23/03/2012 12:16:55 PM]
Index
Contents
Overview
cleaning tool over the hook to place it
on the near side.
(3) Turn the cleaning onto hook.
Close the front cover.
Click on the first or last page to see other MX-4110N / MX-4111N / MX-4112N / MX-4110FN / MX-4111FN / MX-5110N / MX-5111N / MX-5112N / MX-5110FN / MX-5111FN (serv.man16) service manuals if exist.