Sharp MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man10) Service Manual ▷ View online
MX-3640N MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 2
3) Raise the linkage plates on the right and left sides of the front
side of the de sk unit, and fix them with the fixing scr ews
included in the package.
4) Attach the tray 1 and the tray 2.
5) Raise the linkage plates on the right and lef t sides of the rear
side of the de sk unit, and fix them with the fixing scr ews
included in the package.
6) Attach the connection cover included in the package.
C. Release the lock
1) Pull out each tray. Turn and re move the fixing mater ial, and
remove the caution sheet.
Attach the removed fixing material to the position shown in the
figure for storage.
Close the cassette which was pulled out.
Before turning on the power, check to insur e that the fixing
material of the tray is disengaged. If th e power is turned on
without disengaging the fixing mater ial, a tr ouble may be
resulted.
D. Connector connection
1) Remove the cover from the rear side of the machine.
2
1
2
1
2
1
2
1
1
2
MX-3640N MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 3
2) Connect the connector.
3) Split the removed cover along the perforated line.
4) Attach the cover.
E. Turn ON the power of the main unit
1) Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
?
?
For setting the tray size, refer to “Tray size setup” (2-7).
F. Image off-center adjustment
?
The image lead edge position and the off-center adjustment value
of the desk unit have been set to the average value when shipping
from the factory. ?
Therefore, this adjustment must be performed only when the judg-
ment is made to execute it through checking the print image.
2) Enter the SIM50-28 mode.
3) Select [SETUP/PRINT] ADJ with the key button.
4) Select [ALL] with the key button.
4) Select [ALL] with the key button.
?
By pressing [LEAD] or [OFFSET] button, the following items
can be executed individually.
• [LEAD]: Print image lead edge image position adjustment
• [OFFSET]: Print image off-center adjustment
• [LEAD]: Print image lead edge image position adjustment
• [OFFSET]: Print image off-center adjustment
When [ALL] is selected, both of the above two items are
executed simultaneously.
5) Select a paper feed tray to be adjusted.
6) Press [EXECUTE] key.
The patch image (adjustment pattern) is printed out.
2
1
MX-3640N MX-DE12/DE13/DE14 (STAND/1x500/2x500/3x500 SHEET PAPER DRAWER) 4 – 4
7) Set the adjustment pattern on the document table.
Fit the adjustment pattern correctly with the document guide.
In this case, put 5 sheets of white paper on the printed adjust-
ment pattern.
8) Press [EXECUTE] key.
The following item is automatically adjustment.
• Print image lead edge image position adjustment
• Print image off-center adjustment
• Print image lead edge image position adjustment
• Print image off-center adjustment
9) Press [OK] key.
The adjustment result becomes valid.
Perform procedures 4) to 7) for each paper feed tray.
MX-3640N MX-DE20 (STAND500&2000 SHEET PAPER DRAWER) 5 – 1
MX-3640N
Service Manual
[5] MX-DE20 (STAND500&2000 SHEET PAPER DRAWER)
1. Unpacking
If the connector is removed first, it may be damaged during the
installation procedures. Therefore, keep it packed while un-box-
ing. and unpack it only when connecting the connector to the
machine.
A. Packed items check
2. Installation
Before installation, be sure to turn both the oper ation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. Adjuster attachment
1) Turn each adjuster to fix the desk unit.
B. Main unit and desk unit connection
1) Put the main unit on the desk unit.
Use man power of four persons or more to lift the main unit.
Place the main unit on the desk unit slowly by fitting the exter-
nal lines. Check to insure that the positioning pin on the top of
the desk unit is securely engaged in the positioning gr oove of
the main unit.
2) Remove the tray 1 and the desk tray.
No.
Name
Quantity
1
Desk unit
1
2
Fixing screws (M4 x 8)
4
3
Fixing screws (M3 x 8)
4
4
Connection cover
2
5
Connection plate FL
1
6
Connection plate FR
1
7
Connection plate RL
1
8
Connection plate RR
1
Click on the first or last page to see other MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man10) service manuals if exist.