DOWNLOAD Sharp MX-2310U / MX-3111U (serv.man17) Service Manual ↓ Size: 26.68 MB | Pages: 127 in PDF or view online for FREE

MX-3610N  MX-RB10/FN10 (PAPER PASS UNIT/FINISHER)  25 – 2

The punch position labels (No.13 and No.14) should be kept at
hand since they will be necessary when installing the punch unit.

Check to confirm that the firmware version is later than below. 
If the version is older, upgrade the firmware.
Firmware version: 01.07.02.00

Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.

1)

Remove the paper holding arm.

The paper holding arm must be removed together with the
paper holding arm holder. Since the paper holding arm is easy
to remove alone, be careful not to leave the paper holding arm
holder unremoved.

1)

Open the front cabinet, and remove the front cabinet upper.

1

Paper pass unit

1

2

Right cover plate

1

3

Left cabinet

1

4

Reverse tray

1

5

Front cabinet upper

1

6

Resin clip

1

7

Reverse detection actuator

1

8

Paper exit guide sheet

2

9

Fixing screw A (M4 x 7)

4

10

Fixing screw B (M4 x 10)

1

11

Fixing screw C (M4 x 12)

2

12

Fixing screw D (M3 x 8)

1

1

Saddle finisher

1

2

Paper exit tray

1

3

Connection plate

1

4

Saddle tray

1

5

Paper holding A

1

6

Paper holding B

1

7

Fixing screw A

5

8

Fixing screw B

2

9

Fixing screw C

2

10

Staple cartridge

1

11

Staple position label (For scanner)

1

12

Staple position label (For RSPF)

1

13

Punch position label (For scanner)

1

14

Punch position label (For RSPF)

1

2

1

5

7

6

8

9

10

11

12

4

3

2

1

5

7

6

8

9

11

10

12

13

14

3

4

MX-3610N  MX-RB10/FN10 (PAPER PASS UNIT/FINISHER)  25 – 3

2)

Remove the paper exit tray cover.

3)

Remove the paper exit tray.

1)

Remove the paper exit full detection actuator, and attach the
reverse detection actuator.

Be careful of the installing direction of the reverse detection
actuator.

2)

Attach the paper exit guide sheet to the paper exit unit.

3)

Attach the right cover plate.

4)

Hold the rib of the paper exit shifter with the fixing guide, and
fix it with the fixing screw B (M4 x 10).

5)

Attach the left cabinet and fix it with the fixing screw A (M4 x 7).

6)

Attach the front cabinet upper, and fix with the fixing screw C
(M4 x 12).

Attachment reference (Paper exit unit rib)

Attachment reference (Discharge brush rib)

MX-3610N  MX-RB10/FN10 (PAPER PASS UNIT/FINISHER)  25 – 4

7)

Insert the reverse tray along the groove in the left cabinet and
the top surface of the right cover plate.

When inserting the reverse tray, check to insure that the switch
guide of the reverse tray is up.

8)

Fix the reverse tray with the resin clip.

9)

Insert the paper pass unit along the guide rail.
Fix the disconnection preventing lever with the fixing screw D
(M3 x 8).

1)

Remove the operation manual storage cover on the left side of
the machine.

2)

Attach the operation manual storage cover (which was
removed from the machine) to the saddle finisher.

1)

Attach the paper exit tray on the saddle finisher, and fix it with
the fixing screw A.

MX-3610N  MX-RB10/FN10 (PAPER PASS UNIT/FINISHER)  25 – 5

2)

Fix the paper holding A with fixing screw A.

3)

Attach the saddle tray and paper holding B.

1)

Insert the staple cartridge.

1)

Put the saddle finisher closer to the main unit, and check to
insure that the guide pin is smoothly inserted into the connec-
tion hole.

If the guide pin is not inserted smoothly, perform the following
adjustment.

1)

Loosen the fixing screw of the adjustment section on the rear
side. Adjust the height adjustment screw so that the guide pin
is fit with the connection hole in the saddle finisher.

By making space between the main body and ground, the
adjustment screw can be turned by the finger.

2)

Remove the front under cover and foot cover.

Connection hole

Guide pin