Sharp MX-2310U / MX-3111U (serv.man17) Service Manual ▷ View online
MX-3610N MX-PN11A/B/C/D (PUNCH MODULE) 24 – 1
MX-3610N
Service Manual
[24] MX-PN11A/B/C/D (PUNCH MODULE)
1. Unpacking
A. Packed items check
2. Installation
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
Installation of the punch unit must be performed with the inner fin-
isher installed to the machine. If the punch unit is installed without
the inner finisher installed to the machine, when the inner finisher is
installed, the slide rail of the inner finisher may hit the punch unit
connector, damaging the connector.
isher installed to the machine. If the punch unit is installed without
the inner finisher installed to the machine, when the inner finisher is
installed, the slide rail of the inner finisher may hit the punch unit
connector, damaging the connector.
A. Open/close cover and path guide removal
1)
Remove the fulcrum cover.
2)
Remove the clip. Remove the fulcrum, and remove the open/
close cover.
close cover.
3)
Remove the punch F cover.
No.
Name
Quantity
1
Punch unit
1
2
Punch dust label
1
3
Punch position label (For the scanner)
1
4
Punch position label (For the RSPF)
1
2
1
4
3
1
2
2
3
1
1
1
2
MX-3610N MX-PN11A/B/C/D (PUNCH MODULE) 24 – 2
4)
Remove the path guide.
B. Punch unit attachment
1)
Attach the punch unit.
C. Open/close cover attachment
1)
Attach the punch F cover.
2)
Insert the fulcrum shaft into the open/close cover, and attach
the cover and fix it with the clip.
the cover and fix it with the clip.
3)
Attach the fulcrum cover.
D. Label attachment
1)
Attach the punch dust label.
1
2
2
1
1
2
2
2
1
3
1
2
MX-3610N MX-PN11A/B/C/D (PUNCH MODULE) 24 – 3
2)
Attach the punch position label (for the scanner).
3)
Attach the punch position label (for the RSPF).
E. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
First label
Second label
Fit with the corner R.
Label attachment reference
* Corner of the upper
cabinet bottom
No clearance
Ridge line R2.5
R2.5 line of tangency
MX-3610N MX-RB10/FN10 (PAPER PASS UNIT/FINISHER) 25 – 1
MX-3610N
Service Manual
[25] MX-RB10/FN10 (PAPER PASS UNIT/FINISHER)
1. Unpacking
A. Saddle finisher removal
For removal of the saddle stitch finisher, manpower of two persons
or more is required.
or more is required.
1)
Holding the upper part of the saddle stitch finisher by two peo-
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot.)
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot.)
2)
Remove the skid and packing cushions.
3)
One person tilt the saddle stitch finisher, another person
remove the lower tray.
remove the lower tray.
4)
Remove the other side similarly.
1
2
1
2
Click on the first or last page to see other MX-2310U / MX-3111U (serv.man17) service manuals if exist.