DOWNLOAD Sharp MX-1800N (serv.man6) Service Manual ↓ Size: 21.98 MB | Pages: 88 in PDF or view online for FREE

MX-2300/2700 N/G  MX-DEX1/DEX2  2 – 4

1) Pull out each tray.

2) Turn and remove the fixing material, and remove the caution

sheet.

3) Attach the removed fixing material to the position shown in the

figure for storage.

4) Close the cassette which was pulled out.

1)

Remove the screw from the back of the main unit. Remove the
connector cover.

2)

Connect the connector.

3)

Split the removed connector cover along the perforated line.

4)

Install the connector cover and fix it with a screw.

MX-2300/2700 N/G  MX-DEX1/DEX2  2 – 5

1) Connect the earth cord, and insert the power plug of the main

unit into the power outlet.

2) Open the front cabinet.

Turn ON the power switch in the front cabinet of the main unit.

3) Turn ON the power switch on the operation panel.

* For setting the tray size, refer to "Tray size setting" (1-9).

1) Run SIM50-10 using the keypad on the main unit.  

The following screen appears: 

2)

This screen allows you to configure the print off-center adjust-
ment value for each paper feed tray.
<Detailed Description>

3)

On the touch panel, press [

↓] to select "E: 50 : CS3" or "F:

50 : CS4." 

4)

Enter the desired adjustment value through the numeric key-
pad. 
(This value, which defaults to 50, can be adjusted within the
range of 1 to 99).
• Reducing the adjustment value by 1 causes the main scan/

print position to shift by 0.1 mm toward the rear. 

• Increasing the adjustment value by 1 causes the main scan/

print position to shift by 0.1 mm toward the front. 

5)

After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting.

6)

Check that the adjustment pattern image is printed in the cor-
rect position.
Measure the dimensions of the void areas on the front- and
rear-frame sides of the adjustment pattern image, and make
sure that the following conditions are met: 

No adjustment is needed if A - B = 0 

±3.0 mm.

If the above condition is not met, do the following:

7)

Change the adjustment value. 
(Enter a new adjustment value and press the [OK] key).
Changing the adjustment value by 1 shifts the position by
approximately 0.1 mm. 
Repeat steps 4) to 6) until the condition shown in step 6) is sat-
isfied.

8)

After you have completed the adjustment, exit from Simulation
mode by pressing the [CA] key.

0

A:

A : 100

B : 50

BK-MAG
MTF

SIMULATION NO.50-10

PAPER CENTER OFFSET SETUP

100

[64 - 140]

OK

TEST

EXECUTE

CLOSE

C : 50

CS1

D : 50

CS

;
;

;

;

2

E

 CS3

Print off-center adjustment value 
(tray 3)

1 to 99

50

F

 CS4

Print off-center adjustment value 
(tray 4)

1 to 99

50

A-B = 0

3.0mm

+

-

B

A

MX-2300/2700 N/G  MX-TRX1  3 – 1

MX2700N

Service Manual

 

1) Check that all the items are included in the package.

<Note before installation>
* Before starting installation, check to insure that the data lamp on

the operation panel does not light up or blink.

1) Turn OFF the power switch on the operation panel.

2)

Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main unit.

3)

Remove the earth cord and disconnect the power plug of the
main unit from the power outlet.

1)

Open the right door.

2)

Remove the screw, and remove the connector cover. 

1

Exit roller unit

1

2

Full detection actuator

1

1

2

: Dec. 15 2005

MX-2300/2700 N/G  MX-TRX1  3 – 2

3) Remove the screw, and remove the paper exit cover.

4) Connect the connector, and install the exit roller unit (package

part No. 1). Use the screw which was removed in step 3) and
fix the unit. 

5) Install the connector cover, and fix it with the screw. 

6) Install the exit tray unit (A) and the full detection actuator (B)

(package part No. 2). 
* Be careful of the installing direction of the full detection actu-

ator.

1)

Connect the earth cord, and insert the power plug of the main
unit into the power outlet.

2)

Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit. 

3)

Turn ON the power switch on the operation panel.

Use SIM26-1 to set the tray YES/NO.