Sharp AR-RP1 (serv.man2) Service Manual ▷ View online
Digital Copier
Reverse Single Pass
Feeder (RSPF)
Reverse Single Pass
Feeder (RSPF)
MODEL
AR-RP1
[ 1 ] PRODUCT OUTLINE................................................................................ 1
[ 2 ] SPECIFICATIONS .................................................................................... 1
[ 3 ] UNPACKING AND INSTALLATION ......................................................... 1
[ 4 ] EXTERNAL VIEW AND INTERNAL STRUCTURE .................................. 4
[ 5 ] OPEREATIONAL DESCRIPTIONS .......................................................... 4
[ 6 ] ADJUSTMENTS........................................................................................ 6
[ 7 ] DISASSEMBLY AND ASSEMBLY............................................................ 7
[ 8 ] MAINTENANCE ...................................................................................... 13
[ 9 ] ELECTRICAL SECTION......................................................................... 14
CONTENTS
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
SERVICE MANUAL
[1] PRODUCT OUTLINE
This machine is a duplex document auto feeder attached to a digital
copier.
It feeds originals automatically to allow continuous copying.
[2] SPECIFICATIONS
Document set
direction
direction
Face up
Document set
position
position
Center reference
Document transport
system
system
Sheet through type
Document feed
sequence
sequence
Top take-up feed
Document size
AB series: A3 ~ A5
Inch series: 11 x 17 ~ 8.5 x 5.5
Duplex invoice not available
Inch series: 11 x 17 ~ 8.5 x 5.5
Duplex invoice not available
Document weight
56 ~ 90g/m
2
, 11 ~ 23.9lbs
Document set
quantity
quantity
Max. 30 sheets (90g/m
2
, max. thickness
4mm)
Dimensions
583mm (W) x 435mm (D) x 131mm (H)
Weight
About 5.4 kg
Power source
Supplied from the copier.
Document size
detection
detection
On the document feed tray
Detection size
Japan: A3, B4, A4, A4R, B5, B5R
Inch series: 11 x 17, 8.5 x 14, 8.5 x 11,
Inch series: 11 x 17, 8.5 x 14, 8.5 x 11,
8.5 x 11R, 8.5 x 5.5
EX AB series: A3, B4, A4, A4R, A5
Multi copy
Without E-Sort PWB installed:
S S enable, S D disable
D D disable, D S enable
D D disable, D S enable
With E-Sort PWB installed:
S S enable, S D enable,
D D enable, D S enable
D D enable, D S enable
Mixture of different
document sizes
document sizes
Mixture paper feed : Not available during
copying. Available during FAX (same width
only)
copying. Available during FAX (same width
only)
Random paper feed
Not available
Document reverse
Not allowed
Display section (LED)
None
Document exchange
speed
speed
S S 16 sheets/min
[3] UNPACKING AND
INSTALLATION
1. Unpacking
For unpacking, refer to the figure below.
Name
Q’ty
Core
1
Cushion
1
SPF glass holding cover
1
SPF harness
1
Intermediate tray (AR-RP1)
1
Step screw
2
Manual
1
2. Installation
1) Remove the document cover.
Lift the document cover and remove it from the copier.
2) Remove the rear cabinet of the copier.
Remove the seven screws and remove the cabinet. Remove the
connector cover.
If a open/close detection is attached, be careful not to break the
actuator.
actuator.
3) Remove the right cabinet.
Remove the five screws.
4) Remove the document glass holder (left side) and the document
glass.
Remove the two screws and carefully remove the document glass
holder (left side) and the document glass. Do not separate the
glass and holder.
glass and holder.
5) Remove the document glass holder cover (right side).
Remove the two screws.
6) Attach the cushion (one position).
Remove the cover of the double-sided adhesive tape and paste the
cushion taking care not to allow it to extend over the plate edges.
cushion taking care not to allow it to extend over the plate edges.
7) Attach the SPF glass holder cover.
After attaching the SPF glass holding cover, attach the document
glass.
glass.
8) Install the SPF to the copier.
Tilt the SPF backward and insert the hinges into the hinge guides.
9) Remove the PWB shield plate.
Remove the six screws.
10) Install the SPF harness and the ring core (included together with
the unit).
Pass the SPF harness through the plate hole from the above and
fix it to the plate with the supplied two hex cap screws. ( )
fix it to the plate with the supplied two hex cap screws. ( )
Pass the SPF harness through the ring core ( ), and connect it to
the main PWB connector (CN11) inside the copier. ( )
★
Be careful about the direction of the connector.
11) Install the interface harness.
Connect the interface harness from the SPF to the machine and
tighten the screws.
12) Remove the filament tape.
Remove the filament tape at four positions.
13) Install the intermediate tray in the case of RSPF.
In the case of RSPF, install the intermediate tray by pushing it to
the inner part.
3
2
1
