DOWNLOAD Sharp AR-P16 (serv.man3) Service Manual ↓ Size: 5.27 MB | Pages: 26 in PDF or view online for FREE

AR-P16  SETUP  3 - 1

• Ensure that the DATA indicator on the operation panel is neither lit

nor blinking, and then start the installation procedure.

• When installing AR-HD4 (HDD expansion unit), read this installation

manual for installing the unit.

• When installing AR-NC5J (print server card), read this installation

manual for installing the card.

• For improvement of workability, part of the description in this manual

may be modified without prior notice. In this case, refer to the service
manual.

1) Turn off the main switch of the main unit.

Turn the main switch located on the left side of the main unit to the
"OFF" position.

If the machine is equipped with a facsimile unit, also turn off the
FAX power switch.

Then remove the power plug from the outlet.

2) Remove the printer controller slot cover.

(The removed cover is not used any more.)

3) Disconnect the connector of the cooling fan harness.

4) Remove the cooling fan from the printer controller slot cover, and

attach it to the printer controller unit chassis.

• Cooling fan removal

• Cooling fan installation

"OFF"

"OFF"

Remove the fixing screws.

Remove the fixing screws.

Disconnect 
the connector.

Disengage two hooks
of the resin holder.

Insert the rib into the 
chassis hole to attach. 

Fix with two hooks.

AR-P16  SETUP  3 - 2

5) Connect the cooling fan connector to the connector on the control-

ler board.

6) Attach the optional PWBs to the printer control PWB.

∗

<1> Remove the screws that secure the cover and then remove the

cover.

<2> Insert the print server card into the connector of the printer control

PWB.

<3> Secure the print server card using the removed screws.

∗

<1> Among the screws on the printer control PWB, remove the three

screws at the locations (

↑

) shown in the illustration.

<2> Insert the AR-HD4 (HDD expansion unit) to the connector of the

printer control PWB.

<3> Secure the AR-HD4 (HDD expansion unit) using the previously

removed three screws.

∗

Open the right and left pawls of the connector shown in the illustration
and insert the extended memory.

Then close the pawls to lock the connector.

7) Insert the printer controller unit, and fix with the four screws which

were removed in the previous procedure.

8) Connect the cables to the printer control PWB unit.

Connect the Centronics cable <1>, USB cable <2>, and LAN cable
<3> (for a model with a print server card) to the connectors of the
printer control PWB unit.

9) Turn on the main switch of the main unit.

Insert the power plug of the main unit to the outlet.
Then, turn the main switch located on the left side of the main unit
to the "ON" position.
If the machine is equipped with a facsimile unit, also turn on the
FAX power switch.

10) Check the operation.

∗

For installation of the printer driver software on the computer, see
the supplied operation manual.
Then, execute printing from the computer to check for proper printing.

Connect.

  (print server card)

*AR-HD4
 (HDD expansion unit)

Screws

Cover

Screws

Screw

Pawl

Pawl

Fix with screws.

Fix with screws.

Insert into the machine. 

<1>

<2>

<3>

"ON"

"ON"

AR-P16  CONFIGURATION REPORT (TEST PAGE)  4 - 1

  . 

 

 

 

                                                           

 

 

 

 

 

 

 

 

 

 

 

2002/05/23

 

Resolution: 600dpi   

Language: American English 

 

Base Memory: 128MB 

Optional Memory: 128MB 

Total Memory: 256MB 

HDD: 40GB 

 

PCU: 2.00 

ICU: 2.00 

BOOT: 2.00 

PRT: 1.50 

 

Duplex System: Duplex Module 

Paper Feeding Options: Stand/3x500 Sheet Paper Drawer 

Large Capacity Tray: Not Installed 

Paper Exit Options: Finisher 

Print Server Card: Installed 

 

Font Source: Resident 

Pitch Size: 10.00 

Point Size: 12.00 
 

Enable DHCP: No

 

IP Address: 192.168.0.1 

IP Subnet Mask: 255.255.255.0 

IP Gateway: 192.168.0.1 

Enable TCP/IP: Yes 

Enable NetWare: Yes 

Enable NetBEUI: Yes 

NIC Firmware Version: 2.00 

NetWare Print Server Name: Sharp Printer 

NetBEUI Workgroup Name: Sharp Printer 

NetBEUI Printer Name: Sharp Printer 

 

Last Method: Manual Calibration 

Date & Time: 2002/05/23 18:23 

 

Copies: 1Set 

Orientation: Portrait 

Default Paper Size:

 

Letter (8½x11) 

Default Paper Type:

 

Plain 

Default Output Tray: Offset Tray 

2-Sided Print: 1-Sided 

PCL Symbol Set: Roman-8 

Font Number: 0 

Font: Courier 

 

PCL is a registered trademark of Hewlett-Packard Company. NetWare is a registered trademark of Novell, Inc. All other trademarks and copyrights are the property of 
their respective owners. 

Tray 1: Letter (8½x11)   

          / Plain 

Tray 2: Legal (8½x14)

   

          / Letter Head

 

Tray 3: A4   

         

/ Pre-Printed

 

Tray 4: Letter (8½x11R) 

         

/ Plain

 

LCT: A4 

         

/ Plain

 

 

Auto Tray Switching: On 

Total Count: 

Color  9999 

 

B&W  9999

 

1      2      3 
;…;

;…;

;;;

…;…

…;…

AR-P16  HARDWARE  5 - 1

CPU

(IC26)

XPC107

(IC40)

D8501A

(IC22)

(CN15)

USB I/F
(CN13)

NIC I/F (CN9)

SCNIF I/F (CN8)

HDD I/F (CN12)

Engine I/F (CN1)

168pin SDRAM DIMM Slot #0 (CN10)

168pin SDRAM DIMM Slot #1 (CN11)

Parallel

EEPROM

(IC30)

D3032

(IC31)

+

RTC

IC12

IEEE1284 I/F