Sharp AR-M550 (serv.man28) User Manual / Operation Manual ▷ View online
INSERTER
3-17
3
Misfeed removal
When a misfeed occurs in the inserter, remove the misfed paper following the procedure below.
■
■
■
■ Misfeed in the inserter
1
Gently move the inserter away from the
machine while pressing the button.
machine while pressing the button.
2
Remove the misfed paper from the main
unit.
unit.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
After removing the
misfed paper, perform
steps 1 and 3 on page 2-
19 to reset the machine.
misfed paper, perform
steps 1 and 3 on page 2-
19 to reset the machine.
3
If misfed paper is not found in step 2, open
the top cover.
the top cover.
4
Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
5
If a misfeed was not found in step 4, raise
the paper guide lever.
the paper guide lever.
6
Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
7
If a misfeed was not found in step 6,
remove the misfed paper from under the
paper guide.
remove the misfed paper from under the
paper guide.
Be careful not to tear the
misfed paper during
removal.
misfed paper during
removal.
8
Return the paper guide lever to its original
position.
position.
9
Push the finisher to close the gap between
the machine and the inserter.
the machine and the inserter.
After attaching the
inserter on the machine,
make sure that the
paper misfeed message
has been cleared and
the normal message
display appears.
inserter on the machine,
make sure that the
paper misfeed message
has been cleared and
the normal message
display appears.
INSERTER
3-18
Troubleshooting inserter problems
Check the list below before calling for service.
Problem
Check
Solution or cause
Stapling position is
not correct
(including saddle
stitch).
not correct
(including saddle
stitch).
The desired staple mode is not selected.
Select the desired staple mode at the
operation panel of the inserter (page 3-15).
operation panel of the inserter (page 3-15).
The paper is not loaded in the correct
position.
position.
Load the paper correctly (page 3-16).
The paper is not loaded face up.
Paper must be loaded face up in the inserter
tray (page 3-16).
tray (page 3-16).
The inserter does
not operate.
not operate.
Are any inserter covers open?
Close all covers.
"Disabling of inserter" is enabled in the key
operator programs.
operator programs.
Check the key operator programs and disable
"Disabling of inserter".
"Disabling of inserter".
A paper misfeed message appears.
Remove the misfed paper (page 3-17).
The [START] key light is not illuminated.
Make sure that the punch or staple key has
been selected on the operation panel of the
inserter (page 3-15).
been selected on the operation panel of the
inserter (page 3-15).
Paper misfeed
occurs
occurs
The paper is curled or damp.
Do not use curled or folded paper. When the
inserter is not going to be used for a long time,
remove the paper from the inserter, place it in
a bag so that it does not absorb moisture, and
store it in a dark place.
inserter is not going to be used for a long time,
remove the paper from the inserter, place it in
a bag so that it does not absorb moisture, and
store it in a dark place.
Part 2: Copier Operation
Click on the first or last page to see other AR-M550 (serv.man28) service manuals if exist.